[PATCH 2/2] phy: meson: add USB2 PHY support for Meson GXL and GXM
Kishon Vijay Abraham I
kishon at ti.com
Thu Mar 9 00:27:48 PST 2017
Hi,
On Sunday 05 March 2017 03:52 AM, Martin Blumenstingl wrote:
> This adds a new driver for the USB2 PHYs found on Meson GXL and GXM SoCs
> (both SoCs are using the same USB PHY register layout).
>
> The USB2 PHY is a simple PHY which only has a few registers to configure
> the mode (host/device) and a reset register (to enable/disable the PHY).
>
> Unfortunately there are no datasheets available for any of these PHYs.
> Both drivers were written by reading the reference drivers provided by
> Amlogic and analyzing the registers on the kernel that was shipped on
> the boards I have.
>
> Signed-off-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
> ---
> drivers/phy/Kconfig | 13 ++
> drivers/phy/Makefile | 1 +
> drivers/phy/phy-meson-gxl-usb2.c | 263 +++++++++++++++++++++++++++++++++++++++
> 3 files changed, 277 insertions(+)
> create mode 100644 drivers/phy/phy-meson-gxl-usb2.c
>
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index e8eb7f225a88..7d64711a837f 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -486,4 +486,17 @@ config PHY_MESON8B_USB2
> and GXBB SoCs.
> If unsure, say N.
>
> +config PHY_MESON_GXL_USB
> + tristate "Meson GXL and GXM USB2 PHY drivers"
> + default ARCH_MESON
> + depends on OF && (ARCH_MESON || COMPILE_TEST)
> + depends on USB_SUPPORT
> + select USB_COMMON
> + select GENERIC_PHY
> + select REGMAP_MMIO
> + help
> + Enable this to support the Meson USB2 PHYs found in Meson
> + GXL and GXM SoCs.
> + If unsure, say N.
> +
> endmenu
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index 65eb2f436a41..a3a2c7dd5c06 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -59,3 +59,4 @@ obj-$(CONFIG_PHY_CYGNUS_PCIE) += phy-bcm-cygnus-pcie.o
> obj-$(CONFIG_ARCH_TEGRA) += tegra/
> obj-$(CONFIG_PHY_NS2_PCIE) += phy-bcm-ns2-pcie.o
> obj-$(CONFIG_PHY_MESON8B_USB2) += phy-meson8b-usb2.o
> +obj-$(CONFIG_PHY_MESON_GXL_USB) += phy-meson-gxl-usb2.o
> diff --git a/drivers/phy/phy-meson-gxl-usb2.c b/drivers/phy/phy-meson-gxl-usb2.c
> new file mode 100644
> index 000000000000..841a6d9722d4
> --- /dev/null
> +++ b/drivers/phy/phy-meson-gxl-usb2.c
> @@ -0,0 +1,263 @@
> +/*
> + * Meson GXL and GXM USB2 PHY driver
> + *
> + * Copyright (C) 2017 Martin Blumenstingl <martin.blumenstingl at googlemail.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program. If not, see <http://www.gnu.org/licenses/>.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/regmap.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/usb/of.h>
> +
> +/* bits [31:27] are read-only */
> +#define U2P_R0 0x0
> + #define U2P_R0_BYPASS_SEL BIT(0)
> + #define U2P_R0_BYPASS_DM_EN BIT(1)
> + #define U2P_R0_BYPASS_DP_EN BIT(2)
> + #define U2P_R0_TXBITSTUFF_ENH BIT(3)
> + #define U2P_R0_TXBITSTUFF_EN BIT(4)
> + #define U2P_R0_DM_PULLDOWN BIT(5)
> + #define U2P_R0_DP_PULLDOWN BIT(6)
> + #define U2P_R0_DP_VBUS_VLD_EXT_SEL BIT(7)
> + #define U2P_R0_DP_VBUS_VLD_EXT BIT(8)
> + #define U2P_R0_ADP_PRB_EN BIT(9)
> + #define U2P_R0_ADP_DISCHARGE BIT(10)
> + #define U2P_R0_ADP_CHARGE BIT(11)
> + #define U2P_R0_DRV_VBUS BIT(12)
> + #define U2P_R0_ID_PULLUP BIT(13)
> + #define U2P_R0_LOOPBACK_EN_B BIT(14)
> + #define U2P_R0_OTG_DISABLE BIT(15)
> + #define U2P_R0_COMMON_ONN BIT(16)
> + #define U2P_R0_FSEL_MASK GENMASK(19, 17)
> + #define U2P_R0_REF_CLK_SEL_MASK GENMASK(21, 20)
> + #define U2P_R0_POWER_ON_RESET BIT(22)
> + #define U2P_R0_V_ATE_TEST_EN_B_MASK GENMASK(24, 23)
> + #define U2P_R0_ID_SET_ID_DQ BIT(25)
> + #define U2P_R0_ATE_RESET BIT(26)
> + #define U2P_R0_FSV_MINUS BIT(27)
> + #define U2P_R0_FSV_PLUS BIT(28)
> + #define U2P_R0_BYPASS_DM_DATA BIT(29)
> + #define U2P_R0_BYPASS_DP_DATA BIT(30)
> +
> +#define U2P_R1 0x4
> + #define U2P_R1_BURN_IN_TEST BIT(0)
> + #define U2P_R1_ACA_ENABLE BIT(1)
> + #define U2P_R1_DCD_ENABLE BIT(2)
> + #define U2P_R1_VDAT_SRC_EN_B BIT(3)
> + #define U2P_R1_VDAT_DET_EN_B BIT(4)
> + #define U2P_R1_CHARGES_SEL BIT(5)
> + #define U2P_R1_TX_PREEMP_PULSE_TUNE BIT(6)
> + #define U2P_R1_TX_PREEMP_AMP_TUNE_MASK GENMASK(8, 7)
> + #define U2P_R1_TX_RES_TUNE_MASK GENMASK(10, 9)
> + #define U2P_R1_TX_RISE_TUNE_MASK GENMASK(12, 11)
> + #define U2P_R1_TX_VREF_TUNE_MASK GENMASK(16, 13)
> + #define U2P_R1_TX_FSLS_TUNE_MASK GENMASK(20, 17)
> + #define U2P_R1_TX_HSXV_TUNE_MASK GENMASK(22, 21)
> + #define U2P_R1_OTG_TUNE_MASK GENMASK(25, 23)
> + #define U2P_R1_SQRX_TUNE_MASK GENMASK(28, 26)
> + #define U2P_R1_COMP_DIS_TUNE_MASK GENMASK(31, 29)
> +
> +/* bits [31:14] are read-only */
> +#define U2P_R2 0x8
> + #define U2P_R2_DATA_IN_MASK GENMASK(3, 0)
> + #define U2P_R2_DATA_IN_EN_MASK GENMASK(7, 4)
> + #define U2P_R2_ADDR_MASK GENMASK(11, 8)
> + #define U2P_R2_DATA_OUT_SEL BIT(12)
> + #define U2P_R2_CLK BIT(13)
> + #define U2P_R2_DATA_OUT_MASK GENMASK(17, 14)
> + #define U2P_R2_ACA_PIN_RANGE_C BIT(18)
> + #define U2P_R2_ACA_PIN_RANGE_B BIT(19)
> + #define U2P_R2_ACA_PIN_RANGE_A BIT(20)
> + #define U2P_R2_ACA_PIN_GND BIT(21)
> + #define U2P_R2_ACA_PIN_FLOAT BIT(22)
> + #define U2P_R2_CHARGE_DETECT BIT(23)
> + #define U2P_R2_DEVICE_SESSION_VALID BIT(24)
> + #define U2P_R2_ADP_PROBE BIT(25)
> + #define U2P_R2_ADP_SENSE BIT(26)
> + #define U2P_R2_SESSION_END BIT(27)
> + #define U2P_R2_VBUS_VALID BIT(28)
> + #define U2P_R2_B_VALID BIT(29)
> + #define U2P_R2_A_VALID BIT(30)
> + #define U2P_R2_ID_DIG BIT(31)
> +
> +#define U2P_R3 0xc
> +
> +#define RESET_COMPLETE_TIME 500
> +
> +struct phy_meson_gxl_usb2_priv {
> + struct regmap *regmap;
> + enum phy_mode mode;
> + int is_enabled;
> +};
> +
> +static const struct regmap_config phy_meson_gxl_usb2_regmap_conf = {
> + .reg_bits = 8,
> + .val_bits = 32,
> + .reg_stride = 4,
> + .max_register = U2P_R3,
> +};
> +
> +static int phy_meson_gxl_usb2_set_mode(struct phy *phy, enum phy_mode mode)
> +{
> + struct phy_meson_gxl_usb2_priv *priv = phy_get_drvdata(phy);
> +
> + switch (mode) {
> + case PHY_MODE_USB_HOST:
> + case PHY_MODE_USB_OTG:
> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_DM_PULLDOWN,
> + U2P_R0_DM_PULLDOWN);
> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_DP_PULLDOWN,
> + U2P_R0_DP_PULLDOWN);
> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_ID_PULLUP, 0);
> + break;
> +
> + case PHY_MODE_USB_DEVICE:
> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_DM_PULLDOWN,
> + 0);
> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_DP_PULLDOWN,
> + 0);
> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_ID_PULLUP,
> + U2P_R0_ID_PULLUP);
> + break;
> +
> + default:
> + return -EINVAL;
> + }
> +
> + if (priv->is_enabled) {
Should set_mode be always called after power_on? or reset of phy should be done
if set_mode is called after power_on?
Either case I think it's better to move this reset in phy reset ops and invoke
it from this phys users.
Thanks
Kishon
More information about the linux-amlogic
mailing list