[PATCH 1/1] ARM64: dts: meson-gxl: improve support for the P212 reference design
Neil Armstrong
narmstrong at baylibre.com
Tue Feb 28 05:50:44 PST 2017
On 02/19/2017 11:41 PM, Martin Blumenstingl wrote:
> The Amlogic P212 reference design is used by other devices as well, such
> as (for example) the Khadas VIM boards. Thus this patch adds and moves
> all common entries from meson-gxl-s905x-p212.dts to a new, separate
> meson-gxl-s905x-p212.dtsi (which can be re-used on boards such as the
> Khadas VIM).
> Support for all boards based on the P212 reference design includes:
> - enabling IR support
> - enabling the SAR ADC (SARADC_CH1 is connected to a resistor which
> indicates the hardware revision, a similar design is found on the
> Khadas VIM boards)
> - all MMC controllers (which means that SDIO wifi, the SD card and the
> eMMC are now supported)
> - pwm_ef as dependency for the SDIO wifi module
> - uart_A which is connected to the bluetooth module (the bluetooth
> module itself is not enabled yet due to missing devicetree bindings
> for the Broadcom serial bluetooth devices)
> - uart_AO is moved to the .dtsi (as all known devices use it as their
> boot-console)
>
> Specific to the P212 board:
> - this also enables the CVBS connector (which is not available on the
> Khadas VIM boards for example)
>
> Signed-off-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
> ---
> .../boot/dts/amlogic/meson-gxl-s905x-p212.dts | 21 +-
> .../boot/dts/amlogic/meson-gxl-s905x-p212.dtsi | 214 +++++++++++++++++++++
> 2 files changed, 226 insertions(+), 9 deletions(-)
> create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dts
> index 9639f012b02b..db31e093f40e 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dts
> @@ -43,23 +43,26 @@
>
> /dts-v1/;
>
> -#include "meson-gxl-s905x.dtsi"
> +#include "meson-gxl-s905x-p212.dtsi"
>
> / {
> compatible = "amlogic,p212", "amlogic,s905x", "amlogic,meson-gxl";
> model = "Amlogic Meson GXL (S905X) P212 Development Board";
>
> - aliases {
> - serial0 = &uart_AO;
> - };
> + cvbs-connector {
> + compatible = "composite-video-connector";
>
> - chosen {
> - stdout-path = "serial0:115200n8";
> + port {
> + cvbs_connector_in: endpoint {
> + remote-endpoint = <&cvbs_vdac_out>;
> + };
> + };
> };
> +};
>
> - memory at 0 {
> - device_type = "memory";
> - reg = <0x0 0x0 0x0 0x80000000>;
> +&cvbs_vdac_port {
> + cvbs_vdac_out: endpoint {
> + remote-endpoint = <&cvbs_connector_in>;
> };
> };
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi
> new file mode 100644
> index 000000000000..fb0e7c999cb6
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi
> @@ -0,0 +1,214 @@
> +/*
> + * Copyright (c) 2016 Martin Blumenstingl <martin.blumenstingl at googlemail.com>.
> + * Based on meson-gx-p23x-q20x.dtsi:
> + * - Copyright (c) 2016 Endless Computers, Inc.
> + * Author: Carlo Caione <carlo at endlessm.com>
> + * - Copyright (c) 2016 BayLibre, SAS.
> + * Author: Neil Armstrong <narmstrong at baylibre.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This library is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This library is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/* Common DTSI for devices which are based on the P212 reference board. */
> +
> +#include "meson-gxl-s905x.dtsi"
> +
> +/ {
> + aliases {
> + serial0 = &uart_AO;
> + serial1 = &uart_A;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory at 0 {
> + device_type = "memory";
> + reg = <0x0 0x0 0x0 0x80000000>;
> + };
> +
> + vddio_boot: regulator-vddio_boot {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDIO_BOOT";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + vddao_3v3: regulator-vddao_3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDAO_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + vddio_ao18: regulator-vddio_ao18 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDIO_AO18";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + vcc_3v3: regulator-vcc_3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + emmc_pwrseq: emmc-pwrseq {
> + compatible = "mmc-pwrseq-emmc";
> + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
> + };
> +
> + wifi32k: wifi32k {
> + compatible = "pwm-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
> + clocks = <&wifi32k>;
> + clock-names = "ext_clock";
> + };
> +};
> +
> +ðmac {
> + status = "okay";
> +};
> +
> +&ir {
> + status = "okay";
> + pinctrl-0 = <&remote_input_ao_pins>;
> + pinctrl-names = "default";
> +};
> +
> +&saradc {
> + status = "okay";
> + vref-supply = <&vddio_ao18>;
> +};
> +
> +/* Wireless SDIO Module */
> +&sd_emmc_a {
> + status = "okay";
> + pinctrl-0 = <&sdio_pins>;
> + pinctrl-names = "default";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + max-frequency = <100000000>;
> +
> + non-removable;
> + disable-wp;
> +
> + mmc-pwrseq = <&sdio_pwrseq>;
> +
> + vmmc-supply = <&vddao_3v3>;
> + vqmmc-supply = <&vddio_boot>;
> +
> + brcmf: bcrmf at 1 {
> + reg = <1>;
> + compatible = "brcm,bcm4329-fmac";
> + };
> +};
> +
> +/* SD card */
> +&sd_emmc_b {
> + status = "okay";
> + pinctrl-0 = <&sdcard_pins>;
> + pinctrl-names = "default";
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + max-frequency = <100000000>;
> + disable-wp;
> +
> + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
> + cd-inverted;
> +
> + vmmc-supply = <&vddao_3v3>;
> + vqmmc-supply = <&vddio_boot>;
> +};
> +
> +/* eMMC */
> +&sd_emmc_c {
> + status = "okay";
> + pinctrl-0 = <&emmc_pins>;
> + pinctrl-names = "default";
> +
> + bus-width = <8>;
> + cap-sd-highspeed;
> + cap-mmc-highspeed;
> + max-frequency = <200000000>;
> + non-removable;
> + disable-wp;
> + mmc-ddr-1_8v;
> + mmc-hs200-1_8v;
> +
> + mmc-pwrseq = <&emmc_pwrseq>;
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&vddio_boot>;
> +};
> +
> +&pwm_ef {
> + status = "okay";
> + pinctrl-0 = <&pwm_e_pins>;
> + pinctrl-names = "default";
> + clocks = <&clkc CLKID_FCLK_DIV4>;
> + clock-names = "clkin0";
> +};
> +
> +/* This is connected to the Bluetooth module: */
> +&uart_A {
> + status = "okay";
> + pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
> + pinctrl-names = "default";
> + uart-has-rtscts;
> +};
> +
> +&uart_AO {
> + status = "okay";
> + pinctrl-0 = <&uart_ao_a_pins>;
> + pinctrl-names = "default";
> +};
>
Great Job !
It works perfectly on an P212 board.
Tested-by: Neil Armstrong <narmstrong at baylibre.com>
Thanks,
Neil
More information about the linux-amlogic
mailing list