[RFT net-next v2 0/3] dwmac-meson8b: RGMII clock fixes for Meson8b
Emiliano Ingrassia
ingrassia at epigenesys.com
Thu Dec 28 09:51:28 PST 2017
Hi Martin,
thank you for the quick response!
On Thu, Dec 28, 2017 at 05:58:34PM +0100, Martin Blumenstingl wrote:
> Hi Emiliano,
>
> thank you for testing this!
>
> On Thu, Dec 28, 2017 at 5:16 PM, Emiliano Ingrassia
> <ingrassia at epigenesys.com> wrote:
> > Hi Martin, Hi Dave,
> >
> > On Sun, Dec 24, 2017 at 12:40:57AM +0100, Martin Blumenstingl wrote:
> >> Hi Dave,
> >>
> >> please do not apply this series until it got a Tested-by from Emiliano.
> >>
> >>
> >> Hi Emiliano,
> >>
> >> you reported [0] that you couldn't get dwmac-meson8b to work on your
> >> Odroid-C1. With your findings (register dumps, clk_summary output, etc.)
> >> I think I was able to find a fix: it consists of two patches (which you
> >> find in this series)
> >>
> >> Unfortunately I don't have any Meson8b boards with RGMII PHY so I could
> >> only partially test this (I could only check if the clocks were
> >> calculated correctly when using a dummy 500002394Hz input clock instead
> >> of MPLL2).
> >>
> >> Could you please give this series a try and let me know about the
> >> results?
> >> You obviously still need your two "ARM: dts: meson8b" patches which
> >> - add the amlogic,meson8b-dwmac" compatible to meson8b.dtsi
> >> - enable Ethernet on the Odroid-C1
> >>
> >> I have tested this myself on a Khadas VIM (GXL SoC, internal RMII PHY)
> >> and a Khadas VIM2 (GXM SoC, external RGMII PHY). Both are still working
> >> fine (so let's hope that this also fixes your Meson8b issue :)).
> >>
> >>
> >> changes since v1 at [1]:
> >> - changed the subject of the cover-letter to indicate that this is all
> >> about the RGMII clock
> >> - added PATCH #1 which ensures that we don't unnecessarily change the
> >> parent clocks in RMII mode (and also makes the code easier to
> >> understand)
> >> - changed subject of PATCH #2 (formerly PATCH #1) to state that this
> >> is about the RGMII clock
> >> - added Jerome's Reviewed-by to PATCH #2 (formerly PATCH #1)
> >> - replaced PATCH #3 (formerly PATCH #2) with one that sets
> >> CLK_SET_RATE_PARENT on the mux and thus re-configures the MPLL2 clock
> >> on Meson8b correctly
> >>
> >
> > Really thank you for your help and effort. I tried your patch but
> > unfortunately it didn't solve the problem.
> this is probably my fault: I forgot to mention that it requires a fix
> for the 32-bit SoCs in the clock driver ("clk: meson: mpll: use 64-bit
> maths in params_from_rate", see [0]) to work properly
>
Ok, with that patch applied I got:
xtal 1 1 24000000 0 0
sys_pll 0 0 1200000000 0 0
cpu_clk 0 0 1200000000 0 0
vid_pll 0 0 732000000 0 0
fixed_pll 2 2 2550000000 0 0
mpll2 1 1 124999851 0 0
c9410000.ethernet#m250_sel 1 1 124999851 0 0
c9410000.ethernet#m250_div 1 1 124999851 0 0
c9410000.ethernet#m25_div 1 1 24999971 0 0
which is equal to your result. However, the ethernet is still not working.
The prg0 register is set to 0x70A1.
A problem that I see with this solution is that MPLL2 is set to ~125 MHz.
The S805 SoC manual reports that bits 9-7 should contain a value x such
that: MPLL2 = 250 MHz * x (with x >= 1).
In our case, bits 9-7 are set to 1 which is incorrect.
I think that MPLL2 should be 250 MHz at least.
> >
> > Here is the new clk_summary:
> >
> > xtal 1 1 24000000 0 0
> > sys_pll 0 0 1200000000 0 0
> > cpu_clk 0 0 1200000000 0 0
> > vid_pll 0 0 732000000 0 0
> > fixed_pll 2 2 2550000000 0 0
> > mpll2 1 1 106250000 0 0
> > c9410000.ethernet#m250_sel 1 1 106250000 0 0
> > c9410000.ethernet#m250_div 1 1 106250000 0 0
> > c9410000.ethernet#m25_div 1 1 21250000 0 0
> >
> > which leads to a value of 0x70a1 in the prg0 ethernet register.
> > As you can see, something is changed but the RGMII clock is not at 25 MHz.
> > In particular, the bit 10 of prg0, which enables the "generation of 25 MHz
> > clock for PHY" (see S805 manual), is 0.
> assuming that the description in the datasheet is correct
> after Kevin and Mike got updated information from Amlogic about the
> PRG_ETHERNET0 register documenation (see [1]) we thought that bit 10
> means "0 = divide by 5, 1 = divide by 10" (see [2]). I didn't question
> this so far, but I'll test this on a newer SoC later (by forcing
> m250_div to 125MHz, then m25_div will have register value 0 = divide
> by 5)
>
> if the description from the documentation is correct then we need to
> replace m25_div with a fixed-factor clock (mult = 1, div = 5) and make
> it a m25_en gate clock instead
> the resulting clock path would look like this: mpll2 > m250_sel >
> m250_div > fixed_factor > m25_en
>
> > Please, if you have other suggestions let me know.
> could you please re-test this with the patch from [0] applied? no
> other changes should be needed!
>
> > Best regards,
> >
> > Emiliano
> >
> >>
> >> [0] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005596.html
> >> [1] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005848.html
> >>
> >>
> >> Martin Blumenstingl (3):
> >> net: stmmac: dwmac-meson8b: only configure the clocks in RGMII mode
> >> net: stmmac: dwmac-meson8b: fix setting the RGMII clock on Meson8b
> >> net: stmmac: dwmac-meson8b: propagate rate changes to the parent clock
> >>
> >> .../net/ethernet/stmicro/stmmac/dwmac-meson8b.c | 55 +++++++++++-----------
> >> 1 file changed, 27 insertions(+), 28 deletions(-)
> >>
> >> --
> >> 2.15.1
> >>
>
> Regards
> Martin
>
Thank you,
Emiliano
>
> [0] https://patchwork.kernel.org/patch/10131677/
> [1] https://www.mail-archive.com/netdev@vger.kernel.org/msg119290.html
> [2] https://www.mail-archive.com/netdev@vger.kernel.org/msg119293.html
More information about the linux-amlogic
mailing list