[LEDE-DEV] [PATCH] ramips: Add support for the GnuBee Personal Cloud Two
Rosen Penev
rosenp at gmail.com
Sun Feb 4 16:24:15 PST 2018
The GnuBee Personal Cloud Two crowdfunded on https://www.crowdsupply.com
It is a low-cost, low-power, network-attached storage device.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: DDR3 512 MB
- Flash: 32 MB
- Six SATA ports for 3.5" Drives
- One SDcard
- One USB 3.0
- Two USB 2.0
- Gigabit Ethernet: Three Ports
- UART 3.5mm Audio Jack or 3 pin header - 57600 8N1
- Three GPIOs available on a pin header
Flash instructions:
The GnuBee Personal Cloud Two ships with libreCMC installed.
libreCMC is a Free Software Foundation approved fork of LEDE/OpenWrt.
As such one can upgrade using the webinterface or sysupgrade.
Das U-Boot has multiple options for recovery or updates including :
- USB
- http
- tftp
Errata:
- While there are three ethernet ports, the third requires support for
the second GMAC. This will come in kernel 4.14.
- The first hard drive slot has a clearance issue with the two fan
headers. Workaround is to pull the headers out and connect the pins to
jumper wires.
- Using this device as a NAS is problematic with the 4.9 kernel as many
/dev/sdX reads throw silent errors. The current theory behind this is
some kind of unhandled DMA mapping error in the kernel. This is not an
issue with kernel 4.4.
Signed-off-by: L. D. Pinney <ldpinney at gmail.com>
Signed-off-by: Rosen Penev <rosenp at gmail.com>
---
target/linux/ramips/base-files/etc/board.d/01_leds | 6 +
.../linux/ramips/base-files/etc/board.d/02_network | 4 +
target/linux/ramips/base-files/etc/diag.sh | 1 +
target/linux/ramips/base-files/lib/ramips.sh | 3 +
.../ramips/base-files/lib/upgrade/platform.sh | 1 +
target/linux/ramips/dts/GB-PC2.dts | 137 +++++++++++++++++++++
target/linux/ramips/image/mt7621.mk | 8 ++
7 files changed, 160 insertions(+)
create mode 100644 target/linux/ramips/dts/GB-PC2.dts
diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index 37630cd..82abad6 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -191,6 +191,12 @@ gb-pc1)
ucidef_set_led_switch "lan1" "lan1" "$boardname:green:lan1" "switch0" "0x01"
ucidef_set_led_switch "lan2" "lan2" "$boardname:green:lan2" "switch0" "0x10"
;;
+gb-pc2)
+ ucidef_set_led_switch "lan" "lan" "$board:green:lan" "switch0" "0x01"
+ ucidef_set_led_switch "wan" "wan" "$board:green:wan" "switch0" "0x10"
+ ucidef_set_led_netdev "eth1-g" "eth1-g" "$board:green:eth1-g" "eth1"
+ ucidef_set_led_netdev "eth1-y" "eth1-y" "$board:green:eth1-y" "eth1"
+ ;;
gl-mt300a|\
gl-mt300n|\
gl-mt750)
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index 7055327..8e0444d 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -205,6 +205,10 @@ ramips_setup_interfaces()
ucidef_add_switch "switch0" \
"0:lan" "4:lan" "6 at eth0"
;;
+ gb-pc2)
+ ucidef_add_switch "switch0" \
+ "4:lan" "0:wan" "6 at eth0"
+ ;;
gl-mt300n-v2)
ucidef_add_switch "switch0" \
"1:lan" "0:wan" "6 at eth0"
diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index dadb1bb..50824f1 100644
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -90,6 +90,7 @@ get_status_led() {
dir-620-d1|\
dwr-512-b|\
gb-pc1|\
+ gb-pc2|\
hpm|\
hw550-3g|\
mac1200rv2|\
diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index 491320b..9f9b34e 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -205,6 +205,9 @@ ramips_board_detect() {
*"GB-PC1")
name="gb-pc1"
;;
+ *"GB-PC2")
+ name="gb-pc2"
+ ;;
*"GL-MT300A")
name="gl-mt300a"
;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index dd76160..cc47d7e 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -61,6 +61,7 @@ platform_check_image() {
fonera20n|\
freestation5|\
gb-pc1|\
+ gb-pc2|\
gl-mt300a|\
gl-mt300n|\
gl-mt750|\
diff --git a/target/linux/ramips/dts/GB-PC2.dts b/target/linux/ramips/dts/GB-PC2.dts
new file mode 100644
index 0000000..f31ac2b
--- /dev/null
+++ b/target/linux/ramips/dts/GB-PC2.dts
@@ -0,0 +1,137 @@
+/dts-v1/;
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "gnubee,gb-pc2", "mediatek,mt7621-soc";
+ model = "GB-PC2";
+
+ memory at 0 {
+ device_type = "memory";
+ reg = <0x0 0x1c000000>, <0x20000000 0x4000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,57600";
+ };
+
+ palmbus: palmbus at 1E000000 {
+ i2c at 900 {
+ status = "okay";
+ };
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <20>;
+
+ reset {
+ label = "reset";
+ gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ system {
+ label = "gb-pc2:green:system";
+ gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+ };
+
+ status {
+ label = "gb-pc2:green:status";
+ gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
+ };
+
+ lan {
+ label = "gb-pc2:green:lan";
+ gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+ };
+
+ wan {
+ label = "gb-pc2:green:wan";
+ gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
+ };
+
+ eth1-y {
+ label = "gb-pc2:yellow:eth1-y";
+ gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+ };
+
+ eth1-g {
+ label = "gb-pc2:green:eth1-g";
+ gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+ };
+
+ };
+};
+
+&sdhci {
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+
+ m25p80 at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+ m25p,chunked-io = <32>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition at 30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition at 40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition at 50000 {
+ label = "firmware";
+ reg = <0x50000 0x1fb0000>;
+ };
+ };
+};
+
+&cpuclock {
+ compatible = "fixed-clock";
+ clock-frequency = <900000000>;
+};
+
+&pcie {
+ status = "okay";
+};
+
+ðernet {
+ mtd-mac-address = <&factory 0xe000>;
+};
+
+&pinctrl {
+ state_default: pinctrl0 {
+ gpio {
+ ralink,group = "uart3";
+ ralink,function = "gpio";
+ };
+ };
+};
+
diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk
index 8ba65a1..f0b5a84 100644
--- a/target/linux/ramips/image/mt7621.mk
+++ b/target/linux/ramips/image/mt7621.mk
@@ -83,6 +83,14 @@ define Device/gb-pc1
endef
TARGET_DEVICES += gb-pc1
+define Device/gb-pc2
+ DTS := GB-PC2
+ DEVICE_TITLE := GnuBee Personal Cloud Two
+ DEVICE_PACKAGES := kmod-ata-core kmod-ata-ahci kmod-usb3 kmod-sdhci-mt7620
+ IMAGE_SIZE := $(ralink_default_fw_size_32M)
+endef
+TARGET_DEVICES += gb-pc2
+
define Device/hc5962
DTS := HC5962
BLOCKSIZE := 128k
--
2.7.4
More information about the Lede-dev
mailing list