[LEDE-DEV] [PATCH v2] ramips: add support for Ubiquiti EdgeRouter X-SFP

[Drie, Herman van (zakelijk)]

I reported the same before, perhaps a bit different description:
https://bugs.lede-project.org/index.php?do=details&task_id=883&opened=704&ty
pe%5B0%5D=&sev%5B0%5D=&due%5B0%5D=&cat%5B0%5D=&status%5B0%5D=open&percent%5B
0%5D=&reported%5B0%5D=

I found an overview here how ports are connected internally:
https://kazoo.ga/re-visit-the-switch-in-edgerouter-x/

Not sure what it is, the driver file does state 8 ports.
Wondering whether problem is in
/LEDE/snapshot/target/linux/ramips/dts/mt7621.dtsi ?

You are correct that port 5 isn't configured in switch defconfig script upon
boot for ERX-SFP:
/LEDE/snapshot/target/linux/ramips/base-files/etc/board.d/02_network

	tl-wr841n-v13|\
	ubnt-erx|\
	ubnt-erx-sfp|\
	ur-326n4g|\
	wrtnode|\
	wrtnode2p | \
	wrtnode2r | \
	wt3020-4M|\
	wt3020-8M|\
	zbt-wa05)
		ucidef_add_switch "switch0" \
			"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6 at eth0"


-----Original Message-----
From: Lede-dev [mailto:lede-dev-bounces at lists.infradead.org] On Behalf Of
Torbjorn Jansson
Sent: dinsdag 18 juli 2017 18:29
To: Sven Roederer <devel-sven at geroedel.de>; lede-dev at lists.infradead.org
Subject: Re: [LEDE-DEV] [PATCH v2] ramips: add support for Ubiquiti
EdgeRouter X-SFP

On 2017-05-29 11:24, Sven Roederer wrote:
> This patch adds support for the Ubiquiti EdgeRouter X-SFP and improves 
> support for the EdgeRouter X (PoE-passthrough).
> 
> Specification:
> - SoC: MediaTek MT7621AT
> - Flash: 256 MiB
> - RAM: 265 MiB
> - Ethernet: 5 x LAN (1000 Mbps)
> - UART: 1 x UART on PCB (3.3V, RX, TX, GND) - 57600 8N1
> - EdgeRouter X:
>    - 1 x PoE-Passtrough (Eth4)
>    - powered by Wallwart or passive PoE
> - EdgeRouter X-SFP:
>    - 5 x PoE-Out (24V, passive)
>    - 1 x SFP (unknown status)
>    - powered by Wallwart (24V)


regarding the sfp port, it does not show up on the luci switch page.
this port seems to be missing.

what i have is CPU (eth0) and then lan 1 to 4 and a WAN

WAN is the port labeled eth0 on the device and then lan 1-4 must be eth1-4
sfp port is labeled eth5 and as far as i can tell doesn't work.

is this just a minor config issue so this port is perhaps not configured at
all with vlan and so on?

_______________________________________________
Lede-dev mailing list
Lede-dev at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/lede-dev