[openwrt/openwrt] airoha: an7581: enable uart baudrate control

[LEDE Commits]

ansuel pushed a commit to openwrt/openwrt.git, branch openwrt-24.10:
https://git.openwrt.org/f364fe5e09442e030e9b01b320d1664139ef9197

commit f364fe5e09442e030e9b01b320d1664139ef9197
Author: Aleksander Jan Bajkowski <olek2 at wp.pl>
AuthorDate: Sun Sep 14 17:38:24 2025 +0200

    airoha: an7581: enable uart baudrate control
    
    The baud rate control on Airoha does not function properly. This
    patch enables the inactive code responsible for this. The UART2
    baud rate is correct. HSUART3 operates at twice the requested
    baud rate. The same problem exists in the current code, so this
    doesn't introduce any regression. Support for baud rates higher
    than 460800 is still required. This will be added in the future.
    
    Tested on Gemtek W1700k. UART2 and HSUART3 are working fine.
    
    Signed-off-by: Aleksander Jan Bajkowski <olek2 at wp.pl>
    Link: https://github.com/openwrt/openwrt/pull/20049
    Signed-off-by: Robert Marko <robimarko at gmail.com>
    (cherry picked from commit 440b85f5b1025d26b3a40d6b55b34b17cb6520c8)
    [ solve conflict error ]
    Signed-off-by: Christian Marangi <ansuelsmth at gmail.com>
---
 target/linux/airoha/an7581/config-6.6                 |  1 +
 .../patches-6.6/105-uart-add-en7523-support.patch     | 19 +++++++++++++++++++
 2 files changed, 20 insertions(+)

diff --git a/target/linux/airoha/an7581/config-6.6 b/target/linux/airoha/an7581/config-6.6
index 358a953393..8074e514f8 100644
--- a/target/linux/airoha/an7581/config-6.6
+++ b/target/linux/airoha/an7581/config-6.6
@@ -517,6 +517,7 @@ CONFIG_SECURITY=y
 CONFIG_SECURITYFS=y
 # CONFIG_SECURITY_DMESG_RESTRICT is not set
 # CONFIG_SECURITY_NETWORK is not set
+CONFIG_SERIAL_8250_AIROHA=y
 CONFIG_SERIAL_8250_EXTENDED=y
 CONFIG_SERIAL_8250_FSL=y
 CONFIG_SERIAL_8250_NR_UARTS=5
diff --git a/target/linux/airoha/patches-6.6/105-uart-add-en7523-support.patch b/target/linux/airoha/patches-6.6/105-uart-add-en7523-support.patch
index 9ea355370b..39a4944daf 100644
--- a/target/linux/airoha/patches-6.6/105-uart-add-en7523-support.patch
+++ b/target/linux/airoha/patches-6.6/105-uart-add-en7523-support.patch
@@ -135,6 +135,25 @@
  	/*
  	 * LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR
  	 * is written without DLAB set, this mode will be disabled.
+--- a/drivers/tty/serial/8250/Kconfig
++++ b/drivers/tty/serial/8250/Kconfig
+@@ -354,6 +354,16 @@ config SERIAL_8250_ACORN
+ 	  system, say Y to this option.  The driver can handle 1, 2, or 3 port
+ 	  cards.  If unsure, say N.
+ 
++config SERIAL_8250_AIROHA
++	tristate "Airoha UART support"
++	depends on (ARCH_AIROHA || COMPILE_TEST) && OF && SERIAL_8250
++	help
++	  Selecting this option enables an Airoha SoC specific baud rate
++	  calculation routine on an otherwise 16550 compatible UART hardware.
++
++	  If you have an Airoha based board and want to use the serial port,
++	  say Y to this option. If unsure, say N.
++
+ config SERIAL_8250_BCM2835AUX
+ 	tristate "BCM2835 auxiliar mini UART support"
+ 	depends on ARCH_BCM2835 || COMPILE_TEST
 --- a/drivers/tty/serial/8250/Makefile
 +++ b/drivers/tty/serial/8250/Makefile
 @@ -46,6 +46,7 @@ obj-$(CONFIG_SERIAL_8250_PERICOM)	+= 825