[openwrt/openwrt] ath79: qca9563: add support for Amplifi Router HD
LEDE Commits
lede-commits at lists.infradead.org
Sat May 25 10:53:41 PDT 2024
hauke pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/c5b7ec8cee497c3a84eb8ad90d88494f0812698c
commit c5b7ec8cee497c3a84eb8ad90d88494f0812698c
Author: Kristian Skramstad <kristian+github at 83.no>
AuthorDate: Wed Apr 17 15:14:59 2024 +0200
ath79: qca9563: add support for Amplifi Router HD
Hardware:
SoC: Qualcomm Atheros QCA956X ver 1 rev 0
CPU clock: 775.000 MHz
Memory: 128 MB DDR2
Flash: 32 MB SPI NOR mx25l25635e
Switch: Atheros AR8327 rev. 4
Ethernet: 5x 10/100/1000 Mbps (1 WAN + 4 LAN)
Buttons: 1x Reset
Serial: TX, RX, GND, VCC
Baudrate: 115200
Wifi: Qualcomm Atheros qca988x 802.11ac/n - 3x3
Qualcomm Atheros AR9561 802.11b/g/n - 3x3
Not working:
Leds: 1x via a SPI controller
Display: ST7789V or ILI9341V
controlled by stm32f205.
Note:
DSA changes are ready, but we have an issue with
ports not working after 20-30 minutes. So for now
we use swconfig.
Installation: serial connection only
There is a J11 four pin connector. You need to connect TX, RX and GND.
You can find very good information about the device here
https://github.com/alexanderhenne/AFi-R?tab=readme-ov-file#finding-j11
Upgrading via serial port:
1. Download the kernel initramfs image. Copy the image to a TFTP server
2. Connect to console on the AP, and connect the LAN1 port to your PC LAN
3. Stop autoboot to get to U-boot shell
Interrupt the autoboot process by pressing any key when prompted
4. Transfer the kernel image with TFTP
Set your ip address on your TFTP server to 192.168.1.254
# tftpboot 0x81000000 amplifi-router-hd-initramfs-kernel.bin
5. Load the image
# bootm 0x81000000
6. SCP sysupgrade image from your PC to the Amplifi HD
(If you use a newer mac use scp -O)
# scp openwrt-ath79-generic-ubnt_amplifi-router-hd-squashfs-sysupgrade.bin root at 192.168.1.1:/tmp/
7. Write sysupgrade to the firmware partition
# mtd write /tmp/openwrt-ath79-generic-ubnt_amplifi-router-hd-squashfs-sysupgrade.bin firmware
8. Reboot your device
# reboot
Credit to alexanderhenne for all the information.
Signed-off-by: Kristian Skramstad <kristian+github at 83.no>
---
.../ath79/dts/qca9563_ubnt_amplifi-router-hd.dts | 194 +++++++++++++++++++++
.../generic/base-files/etc/board.d/02_network | 4 +
target/linux/ath79/image/generic-ubnt.mk | 12 ++
3 files changed, 210 insertions(+)
diff --git a/target/linux/ath79/dts/qca9563_ubnt_amplifi-router-hd.dts b/target/linux/ath79/dts/qca9563_ubnt_amplifi-router-hd.dts
new file mode 100644
index 0000000000..a322323899
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_ubnt_amplifi-router-hd.dts
@@ -0,0 +1,194 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca956x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "ubnt,amplifi-router-hd", "qca,qca9563";
+ model = "Ubiquiti AmpliFi Router HD";
+
+ aliases {
+ label-mac-device = ð0;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "Reset button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+
+ wifi at 0,0 {
+ compatible = "qcom,ath10k";
+ reg = <0x0000 0 0 0 0>;
+ nvmem-cells = <&cal_art_5000>;
+ nvmem-cell-names = "calibration";
+ };
+};
+
+&spi {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x000000 0x060000>;
+ read-only;
+ };
+
+ partition at 60000 {
+ compatible = "u-boot,env";
+ label = "u-boot-env";
+ reg = <0x060000 0x010000>;
+ };
+
+ partition at 70000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x070000 0xb00000>;
+ };
+
+ partition at b70000 {
+ label = "cfg";
+ reg = <0xb70000 0x0c0000>;
+ read-only;
+ };
+
+ partition at c30000 {
+ label = "recovery";
+ reg = <0xc30000 0x3b0000>;
+ read-only;
+ };
+
+ partition at fe0000 {
+ label = "prst";
+ reg = <0xfe0000 0x010000>;
+ read-only;
+ };
+
+ partition at ff0000 {
+ /* eeprom */
+ label = "art";
+ reg = <0xff0000 0x010000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_art_0: macaddr at 0 {
+ compatible = "mac-base";
+ reg = <0x0 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ cal_art_1000: calibration at 1000 {
+ reg = <0x1000 0x440>;
+ };
+
+ cal_art_5000: calibration at 5000 {
+ reg = <0x5000 0x844>;
+ };
+ };
+ };
+
+ partition at 1000000 {
+ label = "bs1";
+ reg = <0x1000000 0x010000>;
+ };
+
+ partition at 1010000 {
+ label = "bs2";
+ reg = <0x1010000 0x010000>;
+ read-only;
+ };
+
+ partition at 1020000 {
+ label = "stats";
+ reg = <0x1020000 0x400000>;
+ read-only;
+ };
+
+ partition at 1420000 {
+ label = "fw_inactive";
+ reg = <0x1420000 0xb00000>;
+ read-only;
+ };
+
+ partition at 1f20000 {
+ label = "reserved";
+ reg = <0x1f20000 0x0e0000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ phy-mode = "sgmii";
+
+ qca,ar8327-initvals = <
+ 0x04 0x00000080 /* AR8327_REG_PAD0_MODE */
+ 0x08 0x00000000 /* PORT5 PAD MODE CTRL */
+ 0x0c 0x00000000 /* PORT6 PAD MODE CTRL */
+ 0x10 0x602613a0 /* AR8327_REG_POWER_ON_STRAP */
+ 0x50 0xcc35cc35 /* AR8327_REG_LED_CTRL0 */
+ 0x54 0xca35ca35 /* AR8327_REG_LED_CTRL1 */
+ 0x58 0xc935c935 /* AR8327_REG_LED_CTRL2 */
+ 0x5c 0x03ffff00 /* AR8327_REG_LED_CTRL3 */
+ 0x7c 0x0000007e /* AR8327_REG_PORT_STATUS(0) */
+ 0x94 0x00001080 /* AR8327_REG_PORT_STATUS(6) */
+ >;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ pll-data = <0x03000101 0x00000101 0x00001919>;
+
+ phy-mode = "sgmii";
+ phy-handle = <&phy0>;
+
+ nvmem-cells = <&macaddr_art_0 0>;
+ nvmem-cell-names = "mac-address";
+};
+
+&wmac {
+ status = "okay";
+
+ nvmem-cells = <&macaddr_art_0 (-2)>, <&cal_art_1000>;
+ nvmem-cell-names = "mac-address", "calibration";
+};
+
+&usb_phy0 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index bf93dc8ba8..8af618d267 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -554,6 +554,10 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0 at eth0" "2:lan:1" "3:lan:3" "4:lan:2"
;;
+ ubnt,amplifi-router-hd)
+ ucidef_add_switch "switch0" \
+ "0 at eth0" "2:lan:1" "3:lan:3" "4:lan:2" "5:lan:4" "1:wan"
+ ;;
ubnt,edgeswitch-5xp)
ucidef_set_interface_wan "eth1"
ucidef_add_switch "switch0" \
diff --git a/target/linux/ath79/image/generic-ubnt.mk b/target/linux/ath79/image/generic-ubnt.mk
index a4d118456f..f7bab4b697 100644
--- a/target/linux/ath79/image/generic-ubnt.mk
+++ b/target/linux/ath79/image/generic-ubnt.mk
@@ -18,6 +18,18 @@ define Device/ubnt_aircube-isp
endef
TARGET_DEVICES += ubnt_aircube-isp
+define Device/ubnt_amplifi-router-hd
+ IMAGE_SIZE := 11264k
+ UBNT_BOARD := AFi-R-HD
+ UBNT_TYPE := AFi-R
+ UBNT_VERSION := 3.6.3
+ SOC := qca9563
+ DEVICE_MODEL := AmpliFi Router HD
+ UBNT_CHIP := qca956x
+ DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct kmod-usb2
+endef
+TARGET_DEVICES += ubnt_amplifi-router-hd
+
define Device/ubnt_bullet-ac
$(Device/ubnt-2wa)
DEVICE_MODEL := Bullet AC
More information about the lede-commits
mailing list