[openwrt/openwrt] ramips: add support for TP-Link Archer MR200v5
LEDE Commits
lede-commits at lists.infradead.org
Thu May 23 13:47:41 PDT 2024
hauke pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/2a2f53415ed8ed79778edb8135bdbb5e819e587b
commit 2a2f53415ed8ed79778edb8135bdbb5e819e587b
Author: Lea Teuberth <lea.teuberth at outlook.com>
AuthorDate: Tue Apr 2 11:30:32 2024 +0200
ramips: add support for TP-Link Archer MR200v5
Specifications:
CPU: MT7628AN 580MHz
RAM: 64MB DDR2
FLASH: 8MB EN25QH64 NOR SPI
WIFI: 2.4GHz 2x2 MT7628 b/g/n internal
WIFI: 5GHz 1x1 MT7610E ac/n PCI
LTE: Qualcomm MDM9207
ETH: 4xLAN 100base-T integrated
SWITCH: RT3050-ESW Port 0,1,2,3: LAN, Port 6: CPU
LEDS: LAN, WAN, Power, 3x signal strength, WiFi
BTNS: Reset, WiFi toggle
UART: Near ETH ports, Vcc-GND-RX-TX, 115200, 8N1
Installation:
1. Update using recovery mode
- set your IP to 192.168.0.225, subnet mask: 255.255.255.0
- start tftp server, rename tftp-recovery.bin to
tp_recovery.bin and place it into the server's directory
- while holdig the "reset" button, power on the device
- keep holding "reset" until the file is being transferred
Notes:
This board has only one MAC address programmed
in the "romfile" partition:
- MAC for phy0 (2.4GHz) at romfile 0xf100 (0)
- MAC for phy1 (5GHz) at romfile 0xf100 (-1)
- stock firmware re-uses phy0 MAC for ethernet
- stock firmware uses romfile 0xf100 (1) for WWAN;
not used since QMI interface is raw IP
Signed-off-by: Lea Teuberth <lea.teuberth at outlook.com>
---
.../ramips/dts/mt7628an_tplink_archer-mr200-v5.dts | 192 +++++++++++++++++++++
target/linux/ramips/image/mt76x8.mk | 15 ++
.../ramips/mt76x8/base-files/etc/board.d/01_leds | 4 +
.../mt76x8/base-files/etc/board.d/02_network | 5 +
4 files changed, 216 insertions(+)
diff --git a/target/linux/ramips/dts/mt7628an_tplink_archer-mr200-v5.dts b/target/linux/ramips/dts/mt7628an_tplink_archer-mr200-v5.dts
new file mode 100644
index 0000000000..177cd4db8a
--- /dev/null
+++ b/target/linux/ramips/dts/mt7628an_tplink_archer-mr200-v5.dts
@@ -0,0 +1,192 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7628an.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ compatible = "tplink,archer-mr200-v5", "mediatek,mt7628an-soc";
+ model = "TP-Link Archer MR200 v5";
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ label-mac-device = ðernet;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ lan {
+ function = LED_FUNCTION_LAN;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+ };
+
+ wan {
+ function = LED_FUNCTION_WAN;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&gpio 40 GPIO_ACTIVE_LOW>;
+ };
+
+ led_power: power {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
+ };
+
+ signal1 {
+ label = "white:signal1";
+ gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
+ };
+
+ signal2 {
+ label = "white:signal2";
+ gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
+ };
+
+ signal3 {
+ label = "white:signal3";
+ gpios = <&gpio 43 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan {
+ function = LED_FUNCTION_WLAN;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ rfkill {
+ label = "rfkill";
+ gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <104000000>;
+ m25p,fast-read;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x20000>;
+ read-only;
+ };
+
+ partition at 20000 {
+ compatible = "tplink,firmware";
+ label = "firmware";
+ reg = <0x20000 0x7b0000>;
+ };
+
+ partition at 7d0000 {
+ label = "config";
+ reg = <0x7d0000 0x10000>;
+ read-only;
+ };
+
+ partition at 7e0000 {
+ label = "romfile";
+ reg = <0x7e0000 0x10000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_romfile_f100: macaddr at f100 {
+ compatible = "mac-base";
+ reg = <0xf100 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+ };
+ };
+
+ partition at 7f0000 {
+ label = "radio";
+ reg = <0x7f0000 0x10000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ eeprom_radio_0: eeprom at 0 {
+ reg = <0x0 0x400>;
+ };
+
+ eeprom_radio_8000: eeprom at 8000 {
+ reg = <0x8000 0x200>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&state_default {
+ gpio {
+ groups = "i2c", "p0led_an", "p1led_an", "p2led_an", "p3led_an", "p4led_an", "uart1", "wdt";
+ function = "gpio";
+ };
+};
+
+&wmac {
+ nvmem-cells = <&eeprom_radio_0>, <&macaddr_romfile_f100 0>;
+ nvmem-cell-names = "eeprom", "mac-address";
+ status = "okay";
+};
+
+&esw {
+ mediatek,portdisable = <0x30>;
+};
+
+ðernet {
+ nvmem-cells = <&macaddr_romfile_f100 0>;
+ nvmem-cell-names = "mac-address";
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pcie0 {
+ mt76 at 0,0 {
+ reg = <0x0000 0 0 0 0>;
+ ieee80211-freq-limit = <5000000 6000000>;
+ nvmem-cells = <&eeprom_radio_8000>, <&macaddr_romfile_f100 (-1)>;
+ nvmem-cell-names = "eeprom", "mac-address";
+ };
+};
diff --git a/target/linux/ramips/image/mt76x8.mk b/target/linux/ramips/image/mt76x8.mk
index fc81266da9..37c5a034c4 100644
--- a/target/linux/ramips/image/mt76x8.mk
+++ b/target/linux/ramips/image/mt76x8.mk
@@ -606,6 +606,21 @@ define Device/tplink_archer-c50-v6
endef
TARGET_DEVICES += tplink_archer-c50-v6
+define Device/tplink_archer-mr200-v5
+ $(Device/tplink-v2)
+ IMAGE_SIZE := 7872k
+ DEVICE_MODEL := Archer MR200
+ DEVICE_VARIANT := v5
+ TPLINK_FLASHLAYOUT := 8MLmtk
+ TPLINK_HWID := 0x20000005
+ TPLINK_HWREV := 0x5
+ TPLINK_HWREVADD := 0x5
+ DEVICE_PACKAGES := kmod-mt76x0e uqmi kmod-usb2 kmod-usb-serial-option
+ IMAGES := sysupgrade.bin tftp-recovery.bin
+ IMAGE/tftp-recovery.bin := pad-extra 128k | $$(IMAGE/factory.bin)
+endef
+TARGET_DEVICES += tplink_archer-mr200-v5
+
define Device/tplink_re200-v2
$(Device/tplink-safeloader)
IMAGE_SIZE := 7808k
diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
index da3ef154c0..324b57124f 100644
--- a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
@@ -83,6 +83,10 @@ tplink,archer-c50-v6)
ucidef_set_led_wlan "wlan2g" "wlan2g" "green:wlan2g" "phy0tpt"
ucidef_set_led_wlan "wlan5g" "wlan5g" "green:wlan5g" "phy1tpt"
;;
+tplink,archer-mr200-v5)
+ ucidef_set_led_netdev "lan" "lan" "white:lan" "eth0"
+ ucidef_set_led_netdev "wan" "wan" "white:wan" "wwan0"
+ ;;
tplink,re200-v2|\
tplink,re200-v3|\
tplink,re200-v4|\
diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
index fd8c086a85..9fee26e122 100644
--- a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
@@ -153,6 +153,11 @@ ramips_setup_interfaces()
ucidef_add_switch "switch0" \
"0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "6t at eth0"
;;
+ tplink,archer-mr200-v5)
+ ucidef_add_switch "switch0" \
+ "0:lan" "1:lan" "2:lan" "3:lan" "6t at eth0"
+ ucidef_set_interface "wan" device "/dev/cdc-wdm0" protocol "qmi"
+ ;;
tplink,tl-mr3020-v3)
ucidef_add_switch "switch0" \
"0:lan" "6 at eth0"
More information about the lede-commits
mailing list