[openwrt/openwrt] qualcommax: ipq807x: add support for Linksys MX8500
LEDE Commits
lede-commits at lists.infradead.org
Thu May 16 11:27:44 PDT 2024
robimarko pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/9bdaebaff323e554046ce354092832c956b2ad5e
commit 9bdaebaff323e554046ce354092832c956b2ad5e
Author: Paweł Owoc <frut3k7 at gmail.com>
AuthorDate: Mon Feb 26 11:38:02 2024 +0100
qualcommax: ipq807x: add support for Linksys MX8500
Hardware specification:
========
SoC: Qualcomm IPQ8072A
Flash: 512MB (Fidelix FMND4G08S3J-ID)
RAM: 1GB (2x Kingston DDR3L D2516ECMDXGJD)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4 (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 4x4 (Qualcomm QCN5024 + Skyworks SKY8340-11)
IoT: Bluetooth 5, Zigbee and Thread (NXP K32W041)
LED: 1x RGB status (NXP PCA9633)
USB: 1x USB 3.0
Button: WPS, Reset
Flash instructions:
========
1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin image.
More details can be found here: https://www.linksys.com/support-article?articleNum=47547
After first boot check actual partition:
- fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and in case of 1:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd21 0 0
- nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd23 0 0
- nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
3. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
4. Back to the OEM firmware:
- mtd -e kernel -n write FW_MX8500_1.0.11.208937_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MX8500_1.0.11.208937_prod.img alt_kernel
5. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
AQR firmware:
========
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
2. Firmware updating:
Newer firmware (AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld) is available in the latest OEM firmware.
To load this firmware via u-boot, we need to add the MBN header and update 0:ethphyfw partition.
For MBN header we can use script from this repository: https://github.com/testuser7/aqr_mbn_tool
- python aqr_mbn_tool.py AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld
To update partition we need to install kmod-mtd-rw package first:
- insmod mtd-rw.ko i_want_a_brick=1
- mtd -e /dev/mtd26 -n write aqr_fw.mbn /dev/mtd26
Signed-off-by: Paweł Owoc <frut3k7 at gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko at gmail.com>
---
.../boot/uboot-envtools/files/qualcommax_ipq807x | 3 +-
package/firmware/ipq-wifi/Makefile | 2 +
.../arch/arm64/boot/dts/qcom/ipq8072-mx8500.dts | 523 +++++++++++++++++++++
target/linux/qualcommax/image/ipq807x.mk | 8 +
.../ipq807x/base-files/etc/board.d/02_network | 6 +
.../etc/hotplug.d/firmware/11-ath11k-caldata | 7 +-
.../ipq807x/base-files/etc/init.d/bootcount | 3 +-
.../ipq807x/base-files/lib/upgrade/platform.sh | 3 +-
8 files changed, 551 insertions(+), 4 deletions(-)
diff --git a/package/boot/uboot-envtools/files/qualcommax_ipq807x b/package/boot/uboot-envtools/files/qualcommax_ipq807x
index 312fdf8d87..060871396b 100644
--- a/package/boot/uboot-envtools/files/qualcommax_ipq807x
+++ b/package/boot/uboot-envtools/files/qualcommax_ipq807x
@@ -31,7 +31,8 @@ edimax,cax1800)
;;
linksys,mx4200v1|\
linksys,mx4200v2|\
-linksys,mx5300)
+linksys,mx5300|\
+linksys,mx8500)
idx="$(find_mtd_index u_env)"
[ -n "$idx" ] && \
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2"
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile
index 68448a6ec1..2ffd2e014c 100644
--- a/package/firmware/ipq-wifi/Makefile
+++ b/package/firmware/ipq-wifi/Makefile
@@ -37,6 +37,7 @@ ALLWIFIBOARDS:= \
edimax_cax1800 \
linksys_mx4200 \
linksys_mx5300 \
+ linksys_mx8500 \
netgear_lbr20 \
netgear_rax120v2 \
netgear_wax214 \
@@ -157,6 +158,7 @@ $(eval $(call generate-ipq-wifi-package,edgecore_eap102,Edgecore EAP102))
$(eval $(call generate-ipq-wifi-package,edimax_cax1800,Edimax CAX1800))
$(eval $(call generate-ipq-wifi-package,linksys_mx4200,Linksys MX4200))
$(eval $(call generate-ipq-wifi-package,linksys_mx5300,Linksys MX5300))
+$(eval $(call generate-ipq-wifi-package,linksys_mx8500,Linksys MX8500))
$(eval $(call generate-ipq-wifi-package,netgear_lbr20,Netgear LBR20))
$(eval $(call generate-ipq-wifi-package,netgear_rax120v2,Netgear RAX120v2))
$(eval $(call generate-ipq-wifi-package,netgear_wax214,Netgear WAX214))
diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-mx8500.dts b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-mx8500.dts
new file mode 100644
index 0000000000..70f4438ab0
--- /dev/null
+++ b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-mx8500.dts
@@ -0,0 +1,523 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include "ipq8074.dtsi"
+#include "ipq8074-hk-cpu.dtsi"
+#include "ipq8074-ess.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Linksys MX8500";
+ compatible = "linksys,mx8500", "qcom,ipq8074";
+
+ aliases {
+ serial0 = &blsp1_uart5;
+ serial1 = &blsp1_uart3;
+ led-boot = &led_system_blue;
+ led-running = &led_system_blue;
+ led-failsafe = &led_system_red;
+ led-upgrade = &led_system_green;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs-append = " root=/dev/ubiblock0_0 rootfstype=squashfs ro";
+ };
+
+ gpio_export {
+ compatible = "gpio-export";
+ #size-cells = <0>;
+
+ bt_pwr {
+ gpio-export,name = "bt_pwr";
+ gpio-export,output = <1>;
+ gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&button_pins>;
+ pinctrl-names = "default";
+
+ reset-button {
+ label = "reset";
+ gpios = <&tlmm 67 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps-button {
+ label = "wps";
+ gpios = <&tlmm 64 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+};
+
+&tlmm {
+ button_pins: button-state {
+ pins = "gpio64", "gpio67";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ mdio_pins: mdio-state {
+ mdc-pins {
+ pins = "gpio68";
+ function = "mdc";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ mdio-pins {
+ pins = "gpio69";
+ function = "mdio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+};
+
+&blsp1_uart3 {
+ status = "okay";
+};
+
+&blsp1_uart5 {
+ status = "okay";
+};
+
+&prng {
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&crypto {
+ status = "okay";
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&qpic_nand {
+ status = "okay";
+
+ /*
+ * Bootloader will find the NAND DT node by the compatible and
+ * then "fixup" it by adding the partitions from the SMEM table
+ * using the legacy bindings thus making it impossible for us
+ * to change the partition table or utilize NVMEM for calibration.
+ * So add a dummy partitions node that bootloader will populate
+ * and set it as disabled so the kernel ignores it instead of
+ * printing warnings due to the broken way bootloader adds the
+ * partitions.
+ */
+ partitions {
+ status = "disabled";
+ };
+
+ nand at 0 {
+ reg = <0>;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ nand-bus-width = <8>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "0:sbl1";
+ reg = <0x0 0x100000>;
+ read-only;
+ };
+
+ partition at 100000 {
+ label = "0:mibib";
+ reg = <0x100000 0x100000>;
+ read-only;
+ };
+
+ partition at 200000 {
+ label = "0:bootconfig";
+ reg = <0x200000 0x80000>;
+ read-only;
+ };
+
+ partition at 280000 {
+ label = "0:bootconfig1";
+ reg = <0x280000 0x80000>;
+ read-only;
+ };
+
+ partition at 300000 {
+ label = "0:qsee";
+ reg = <0x300000 0x300000>;
+ read-only;
+ };
+
+ partition at 600000 {
+ label = "0:qsee_1";
+ reg = <0x600000 0x300000>;
+ read-only;
+ };
+
+ partition at 900000 {
+ label = "0:devcfg";
+ reg = <0x900000 0x80000>;
+ read-only;
+ };
+
+ partition at 980000 {
+ label = "0:devcfg_1";
+ reg = <0x980000 0x80000>;
+ read-only;
+ };
+
+ partition at a00000 {
+ label = "0:apdp";
+ reg = <0xa00000 0x80000>;
+ read-only;
+ };
+
+ partition at a80000 {
+ label = "0:apdp_1";
+ reg = <0xa80000 0x80000>;
+ read-only;
+ };
+
+ partition at b00000 {
+ label = "0:rpm";
+ reg = <0xb00000 0x80000>;
+ read-only;
+ };
+
+ partition at b80000 {
+ label = "0:rpm_1";
+ reg = <0xb80000 0x80000>;
+ read-only;
+ };
+
+ partition at c00000 {
+ label = "0:cdt";
+ reg = <0xc00000 0x80000>;
+ read-only;
+ };
+
+ partition at c80000 {
+ label = "0:cdt_1";
+ reg = <0xc80000 0x80000>;
+ read-only;
+ };
+
+ partition at d00000 {
+ label = "0:appsblenv";
+ reg = <0xd00000 0x80000>;
+ };
+
+ partition at d80000 {
+ label = "0:appsbl";
+ reg = <0xd80000 0x100000>;
+ read-only;
+ };
+
+ partition at e80000 {
+ label = "0:appsbl_1";
+ reg = <0xe80000 0x100000>;
+ read-only;
+ };
+
+ partition at f80000 {
+ label = "0:art";
+ reg = <0xf80000 0x80000>;
+ read-only;
+ };
+
+ partition at 1000000 {
+ label = "u_env";
+ reg = <0x1000000 0x40000>;
+ };
+
+ partition at 1040000 {
+ label = "s_env";
+ reg = <0x1040000 0x20000>;
+ };
+
+ partition at 1060000 {
+ label = "devinfo";
+ reg = <0x1060000 0x20000>;
+ read-only;
+ };
+
+ partition at 1080000 {
+ label = "kernel";
+ reg = <0x1080000 0x9600000>;
+ };
+
+ partition at 1680000 {
+ label = "rootfs";
+ reg = <0x1680000 0x9000000>;
+ };
+
+ partition at a680000 {
+ label = "alt_kernel";
+ reg = <0xa680000 0x9600000>;
+ };
+
+ partition at ac80000 {
+ label = "alt_rootfs";
+ reg = <0xac80000 0x9000000>;
+ };
+
+ partition at 13c80000 {
+ label = "sysdiag";
+ reg = <0x13c80000 0x200000>;
+ read-only;
+ };
+
+ partition at 13e80000 {
+ label = "0:ethphyfw";
+ reg = <0x13e80000 0x100000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ aqr_fw: firmware at 0 {
+ /* Skip the QCOM MBN Header of 40 bytes */
+ reg = <0x28 0x60002>;
+ };
+ };
+ };
+
+ partition at 13f80000 {
+ label = "syscfg";
+ reg = <0x13f80000 0xb180000>;
+ read-only;
+ };
+
+ partition at 1f100000 {
+ label = "app_data";
+ reg = <0x1f100000 0x500000>;
+ read-only;
+ };
+
+ partition at 1f600000 {
+ label = "0:wififw";
+ reg = <0x1f600000 0xa00000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&blsp1_i2c2 {
+ status = "okay";
+
+ led-controller at 62 {
+ compatible = "nxp,pca9633";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x62>;
+ nxp,hw-blink;
+
+ led_system_red: led at 0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_STATUS;
+ };
+
+ led_system_green: led at 1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ };
+
+ led_system_blue: led at 2 {
+ reg = <2>;
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_STATUS;
+ };
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>;
+
+ ethernet-phy-package at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "qcom,qca8075-package";
+ reg = <0>;
+
+ qcom,package-mode = "qsgmii";
+
+ qca8075_0: ethernet-phy at 0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+
+ qca8075_1: ethernet-phy at 1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+
+ qca8075_2: ethernet-phy at 2 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <2>;
+ };
+
+ qca8075_3: ethernet-phy at 3 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <3>;
+ };
+ };
+
+ aqr114c: ethernet-phy at 8 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <8>;
+ reset-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
+ firmware-name = "marvell/AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld";
+ nvmem-cells = <&aqr_fw>;
+ nvmem-cell-names = "firmware";
+ };
+};
+
+&switch {
+ status = "okay";
+
+ switch_lan_bmp = <(ESS_PORT1 | ESS_PORT2 | ESS_PORT3 | ESS_PORT4)>; /* lan port bitmap */
+ switch_wan_bmp = <ESS_PORT6>; /* wan port bitmap */
+ switch_mac_mode = <MAC_MODE_QSGMII>; /* mac mode for uniphy instance0*/
+ switch_mac_mode2 = <MAC_MODE_USXGMII>; /* mac mode for uniphy instance2*/
+
+ qcom,port_phyinfo {
+ port at 1 {
+ port_id = <1>;
+ phy_address = <0>;
+ };
+
+ port at 2 {
+ port_id = <2>;
+ phy_address = <1>;
+ };
+
+ port at 3 {
+ port_id = <3>;
+ phy_address = <2>;
+ };
+
+ port at 4 {
+ port_id = <4>;
+ phy_address = <3>;
+ };
+
+ port at 6 {
+ port_id = <6>;
+ phy_address = <8>;
+ compatible = "ethernet-phy-ieee802.3-c45";
+ ethernet-phy-ieee802.3-c45;
+ };
+ };
+};
+
+&edma {
+ status = "okay";
+};
+
+&dp1 {
+ status = "okay";
+ phy-mode = "qsgmii";
+ phy-handle = <&qca8075_0>;
+ label = "lan1";
+};
+
+&dp2 {
+ status = "okay";
+ phy-mode = "qsgmii";
+ phy-handle = <&qca8075_1>;
+ label = "lan2";
+};
+
+&dp3 {
+ status = "okay";
+ phy-mode = "qsgmii";
+ phy-handle = <&qca8075_2>;
+ label = "lan3";
+};
+
+&dp4 {
+ status = "okay";
+ phy-mode = "qsgmii";
+ phy-handle = <&qca8075_3>;
+ label = "lan4";
+};
+
+&dp6_syn {
+ status = "okay";
+ phy-mode = "usxgmii";
+ phy-handle = <&aqr114c>;
+ label = "wan";
+};
+
+&ssphy_0 {
+ status = "okay";
+};
+
+&qusb_phy_0 {
+ status = "okay";
+};
+
+&usb_0 {
+ status = "okay";
+};
+
+&pcie_qmp0 {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+
+ perst-gpio = <&tlmm 61 GPIO_ACTIVE_LOW>;
+
+ bridge at 0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi at 1,0 {
+ status = "okay";
+
+ /* ath11k has no DT compatible for PCI cards */
+ compatible = "pci17cb,1104";
+ reg = <0x00010000 0 0 0 0>;
+
+ qcom,ath11k-calibration-variant = "Linksys-MX8500";
+ };
+ };
+};
+
+&wifi {
+ status = "okay";
+
+ qcom,ath11k-calibration-variant = "Linksys-MX8500";
+};
diff --git a/target/linux/qualcommax/image/ipq807x.mk b/target/linux/qualcommax/image/ipq807x.mk
index a4fd6ff796..007c73555e 100644
--- a/target/linux/qualcommax/image/ipq807x.mk
+++ b/target/linux/qualcommax/image/ipq807x.mk
@@ -140,6 +140,14 @@ define Device/linksys_mx5300
endef
TARGET_DEVICES += linksys_mx5300
+define Device/linksys_mx8500
+ $(call Device/linksys_mx)
+ DEVICE_MODEL := MX8500
+ DEVICE_PACKAGES += ipq-wifi-linksys_mx8500 kmod-ath11k-pci \
+ ath11k-firmware-qcn9074 kmod-bluetooth
+endef
+TARGET_DEVICES += linksys_mx8500
+
define Device/netgear_rax120v2
$(call Device/FitImage)
$(call Device/UbiFit)
diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network
index d87e4246e1..380588bbab 100644
--- a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network
+++ b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network
@@ -15,6 +15,7 @@ ipq807x_setup_interfaces()
buffalo,wxr-5950ax12|\
dynalink,dl-wrx36|\
linksys,mx5300|\
+ linksys,mx8500|\
xiaomi,ax9000|\
zbtlink,zbt-z800ax)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
@@ -76,6 +77,11 @@ ipq807x_setup_macs()
done
[ "$(mtd_get_mac_ascii u_env eth2addr)" != "$label_mac" ] && wan_mac=$label_mac
;;
+ linksys,mx8500)
+ label_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
+ lan_mac=$(macaddr_add $label_mac 1)
+ wan_mac=$label_mac
+ ;;
esac
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
index c40d9bc5f9..018e828859 100644
--- a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
+++ b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
@@ -29,7 +29,8 @@ case "$FIRMWARE" in
zte,mf269)
caldata_extract "0:art" 0x1000 0x20000
;;
- linksys,mx4200v1)
+ linksys,mx4200v1|\
+ linksys,mx8500)
caldata_extract "0:art" 0x1000 0x20000
ath11k_remove_regdomain
;;
@@ -66,6 +67,10 @@ case "$FIRMWARE" in
"ath11k/QCN9074/hw1.0/cal-pci-0000:01:00.0.bin"|\
"ath11k/QCN9074/hw1.0/cal-pci-0001:01:00.0.bin")
case "$board" in
+ linksys,mx8500)
+ caldata_extract "0:art" 0x26800 0x20000
+ ath11k_remove_regdomain
+ ;;
prpl,haze)
caldata_extract_mmc "0:ART" 0x26800 0x20000
;;
diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/init.d/bootcount b/target/linux/qualcommax/ipq807x/base-files/etc/init.d/bootcount
index 3e81caf63f..26da7cd614 100755
--- a/target/linux/qualcommax/ipq807x/base-files/etc/init.d/bootcount
+++ b/target/linux/qualcommax/ipq807x/base-files/etc/init.d/bootcount
@@ -12,7 +12,8 @@ boot() {
;;
linksys,mx4200v1|\
linksys,mx4200v2|\
- linksys,mx5300)
+ linksys,mx5300|\
+ linksys,mx8500)
mtd resetbc s_env || true
;;
esac
diff --git a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh
index b9668d0af4..b99657fb4c 100644
--- a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh
+++ b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh
@@ -77,7 +77,8 @@ platform_do_upgrade() {
;;
linksys,mx4200v1|\
linksys,mx4200v2|\
- linksys,mx5300)
+ linksys,mx5300|\
+ linksys,mx8500)
boot_part="$(fw_printenv -n boot_part)"
if [ "$boot_part" -eq "1" ]; then
fw_setenv boot_part 2
More information about the lede-commits
mailing list