[openwrt/openwrt] ipq40xx: add support for Linksys WHW03 V1
LEDE Commits
lede-commits at lists.infradead.org
Sun May 5 01:33:17 PDT 2024
robimarko pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/c90487556229ae264dec33305e5c71c4ef7dd1c5
commit c90487556229ae264dec33305e5c71c4ef7dd1c5
Author: Rodrigo Balerdi <lanchon at gmail.com>
AuthorDate: Thu Apr 11 12:14:19 2024 -0300
ipq40xx: add support for Linksys WHW03 V1
Hardware:
=========
SOC: Qualcomm IPQ4019
WiFi 1: QCA4019 IEEE 802.11b/g/n
WiFi 2: QCA4019 IEEE 802.11a/n/ac
WiFi 3: QCA9886 IEEE 802.11a/n/ac
Bluetooth: Qualcomm CSR8510 (A10)
Zigbee: Silicon Labs EM3581 NCP + Skyworks SE2432L
Ethernet: Qualcomm Atheros QCA8072 (2-port)
Flash: Samsung KLM4G1FEPD (4GB eMMC)
RAM (NAND): 512MB
LED Controller: NXP PCA9633 (I2C)
Buttons: Single reset button (GPIO).
Ethernet:
=========
The device has 2 ethernet ports, configured as follows by default:
- left port: WAN
- right port: LAN
Wifi:
=====
The Wifi radios are turned off by default. To configure the router,
you will need to connect your computer to the LAN port of the device.
Bluetooth and Zigbee:
=====================
Configuration included but not tested.
Storage:
========
For compatibility with stock firmware, all of OpenWrt runs in a 136 MiB
eMMC partition (of which there are two copies, see below). You can also
use partition /dev/mmcblk0p19 "syscfg" (3.4 GiB) any way you see fit.
During very limited tests, stock firmware did not mount this partition.
However, backing up its stock content before use is recommended anyway.
Firmware:
=========
The device uses a dual firmware mechanism: it automatically reverts to
the previous firmware after 3 failed boot attempts.
You can switch to the inactive firmware copy by changing the "boot_part"
U-Boot environment variable. You can also do it by turning on the device
for a couple of seconds and then back off, 3 times in a row.
Installation:
=============
OpenWrt's "factory" image can be installed via the stock web UI:
1. Login to the UI. (The default password is printed on the label.)
2. Enter support mode by clicking on the "CA" link at the bottom.
3. Click "Connectivity", "Choose file", "Start", and ignore warnings.
This port is based on work done by flipy (https://github.com/flipy).
Signed-off-by: Rodrigo Balerdi <lanchon at gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15345
Signed-off-by: Robert Marko <robimarko at gmail.com>
---
package/boot/uboot-envtools/files/ipq40xx | 3 +
.../ipq40xx/base-files/etc/board.d/02_network | 5 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 12 +
.../linux/ipq40xx/base-files/etc/init.d/bootcount | 32 ++
.../lib/preinit/05_set_iface_mac_ipq40xx.sh | 6 +
.../ipq40xx/base-files/lib/upgrade/linksys.sh | 68 ++++
.../ipq40xx/base-files/lib/upgrade/platform.sh | 6 +-
.../arch/arm/boot/dts/qcom/qcom-ipq4019-whw03.dts | 351 +++++++++++++++++++++
target/linux/ipq40xx/image/generic.mk | 14 +
9 files changed, 496 insertions(+), 1 deletion(-)
diff --git a/package/boot/uboot-envtools/files/ipq40xx b/package/boot/uboot-envtools/files/ipq40xx
index 8cada7334b..717158b042 100644
--- a/package/boot/uboot-envtools/files/ipq40xx
+++ b/package/boot/uboot-envtools/files/ipq40xx
@@ -67,6 +67,9 @@ linksys,mr8300)
linksys,whw01)
ubootenv_add_uci_config "/dev/mtd6" "0x0" "0x40000" "0x10000"
;;
+linksys,whw03)
+ ubootenv_add_uci_config "/dev/mmcblk0p11" "0x0" "0x100000"
+ ;;
linksys,whw03v2)
ubootenv_add_uci_config "/dev/mtd6" "0x0" "0x80000" "0x20000"
;;
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 02059580a1..e86d24fab5 100644
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -37,6 +37,7 @@ ipq40xx_setup_interfaces()
glinet,gl-ap1300|\
glinet,gl-b2200|\
google,wifi|\
+ linksys,whw03|\
linksys,whw03v2|\
luma,wrtq-329acn|\
mikrotik,cap-ac|\
@@ -215,6 +216,10 @@ ipq40xx_setup_macs()
wan_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
lan_mac=$(macaddr_add "$wan_mac" 1)
;;
+ linksys,whw03)
+ wan_mac=$(mmc_get_mac_ascii devinfo hw_mac_addr)
+ lan_mac="$wan_mac"
+ ;;
mikrotik,cap-ac |\
mikrotik,hap-ac2|\
mikrotik,hap-ac3|\
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 654be2697a..3b7f44282d 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -40,6 +40,10 @@ case "$FIRMWARE" in
# OEM assigns 4 sequential MACs
ath10k_patch_mac $(macaddr_setbit_la $(macaddr_add "$(cat /sys/class/net/eth0/address)" 4))
;;
+ linksys,whw03)
+ caldata_extract_mmc "0:ART" 0x9000 0x2f20
+ ath10k_patch_mac $(macaddr_add "$(cat /sys/class/net/eth0/address)" 3)
+ ;;
netgear,rbr40|\
netgear,rbs40|\
netgear,rbr50|\
@@ -104,6 +108,10 @@ case "$FIRMWARE" in
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(macaddr_add "$(cat /sys/class/net/eth0/address)" 2)
;;
+ linksys,whw03)
+ caldata_extract_mmc "0:ART" 0x1000 0x2f20
+ ath10k_patch_mac $(macaddr_add "$(cat /sys/class/net/eth0/address)" 1)
+ ;;
meraki,mr33 |\
meraki,mr74)
caldata_extract_ubi "ART" 0x1000 0x2f20
@@ -200,6 +208,10 @@ case "$FIRMWARE" in
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add "$(cat /sys/class/net/eth0/address)" 3)
;;
+ linksys,whw03)
+ caldata_extract_mmc "0:ART" 0x5000 0x2f20
+ ath10k_patch_mac $(macaddr_add "$(cat /sys/class/net/eth0/address)" 2)
+ ;;
meraki,mr33 |\
meraki,mr74)
caldata_extract_ubi "ART" 0x5000 0x2f20
diff --git a/target/linux/ipq40xx/base-files/etc/init.d/bootcount b/target/linux/ipq40xx/base-files/etc/init.d/bootcount
index df656c9b85..0120f78cfe 100755
--- a/target/linux/ipq40xx/base-files/etc/init.d/bootcount
+++ b/target/linux/ipq40xx/base-files/etc/init.d/bootcount
@@ -2,6 +2,35 @@
START=99
+mmc_resetbc() {
+ local part_label="$1"
+
+ . /lib/functions.sh
+
+ local part_device="$(find_mmc_part "$part_label")"
+ if [ "$part_device" = "" ]; then
+ >&2 echo "mmc_resetbc: Unknown partition label: $part_label"
+ return 1
+ fi
+
+ local magic_number="$(hexdump -e '"0x%02x\n"' -n 4 "$part_device")"
+ if [ "$magic_number" != "0x20110811" ]; then
+ >&2 echo "mmc_resetbc: Unexpected partition magic: $magic_number"
+ return 1
+ fi
+
+ local last_count=$(hexdump -e '"0x%02x\n"' -n 4 -s 4 "$part_device")
+ if [ "$last_count" != "0x00" ]; then
+ printf "\x00" | dd of="$part_device" bs=4 seek=1 count=1 conv=notrunc 2>/dev/null
+
+ last_count=$(hexdump -e '"0x%02x\n"' -n 4 -s 4 "$part_device")
+ if [ "$last_count" != "0x00" ]; then
+ >&2 echo "mmc_resetbc: Unable to reset boot counter"
+ return 1
+ fi
+ fi
+}
+
boot() {
case $(board_name) in
alfa-network,ap120c-ac)
@@ -15,6 +44,9 @@ boot() {
linksys,whw03v2)
mtd resetbc s_env || true
;;
+ linksys,whw03)
+ mmc_resetbc s_env || true
+ ;;
netgear,wac510)
fw_setenv boot_cnt=0
;;
diff --git a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh
index 96e70f62a9..1ede544aac 100644
--- a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh
+++ b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh
@@ -30,6 +30,12 @@ preinit_set_mac_address() {
ip link set dev lan1 address $(macaddr_add "$base_mac" 1)
ip link set dev eth0 address $(macaddr_setbit "$base_mac" 7)
;;
+ linksys,whw03)
+ base_mac=$(mmc_get_mac_ascii devinfo hw_mac_addr)
+ ip link set dev eth0 address "$base_mac"
+ ip link set dev lan address "$base_mac"
+ ip link set dev wan address "$base_mac"
+ ;;
mikrotik,wap-ac|\
mikrotik,wap-ac-lte|\
mikrotik,wap-r-ac)
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/linksys.sh b/target/linux/ipq40xx/base-files/lib/upgrade/linksys.sh
index 18366fc622..860c3fd2de 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/linksys.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/linksys.sh
@@ -123,3 +123,71 @@ platform_do_upgrade_linksys() {
get_image "$1" | mtd -e "$part_label" write - "$part_label"
}
}
+
+linksys_get_cmdline_rootfs_device() {
+ if read cmdline < /proc/cmdline; then
+ case "$cmdline" in
+ *root=*)
+ local str="${cmdline##*root=}"
+ echo "${str%% *}"
+ return
+ ;;
+ esac
+ fi
+ return 1
+}
+
+linksys_get_current_boot_part_emmc() {
+ local boot_part="$(fw_printenv -n boot_part)"
+ if [ "$boot_part" = 1 ] || [ "$boot_part" = 2 ]; then
+ v "Current boot_part=$boot_part selected from bootloader environment"
+ else
+ local rootfs_device="$(linksys_get_cmdline_rootfs_device)"
+ if [ "$rootfs_device" = "$(find_mmc_part "rootfs")" ]; then
+ boot_part=1
+ elif [ "$rootfs_device" = "$(find_mmc_part "alt_rootfs")" ]; then
+ boot_part=2
+ else
+ v "Could not determine current boot_part"
+ return 1
+ fi
+ v "Current boot_part=$boot_part selected from cmdline rootfs=$rootfs_device"
+ fi
+ echo $boot_part
+}
+
+linksys_set_target_partitions_emmc() {
+ local current_boot_part="$1"
+
+ if [ "$current_boot_part" = 1 ]; then
+ CI_KERNPART="alt_kernel"
+ CI_ROOTPART="alt_rootfs"
+ fw_setenv -s - <<-EOF
+ boot_part 2
+ auto_recovery yes
+ EOF
+ elif [ "$current_boot_part" = 2 ]; then
+ CI_KERNPART="kernel"
+ CI_ROOTPART="rootfs"
+ fw_setenv -s - <<-EOF
+ boot_part 1
+ auto_recovery yes
+ EOF
+ else
+ v "Could not set target eMMC partitions"
+ return 1
+ fi
+
+ v "Target eMMC partitions: $CI_KERNPART, $CI_ROOTPART"
+}
+
+platform_do_upgrade_linksys_emmc() {
+ local file="$1"
+
+ mkdir -p /var/lock
+ local current_boot_part="$(linksys_get_current_boot_part_emmc)"
+ linksys_set_target_partitions_emmc "$current_boot_part" || exit 1
+ touch /var/lock/fw_printenv.lock
+
+ emmc_do_upgrade "$file"
+}
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index e934326849..53a9561148 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -175,6 +175,9 @@ platform_do_upgrade() {
linksys,whw03v2)
platform_do_upgrade_linksys "$1"
;;
+ linksys,whw03)
+ platform_do_upgrade_linksys_emmc "$1"
+ ;;
meraki,mr33 |\
meraki,mr74)
CI_KERNPART="part.safe"
@@ -236,7 +239,8 @@ platform_do_upgrade() {
platform_copy_config() {
case "$(board_name)" in
glinet,gl-b2200 |\
- google,wifi)
+ google,wifi |\
+ linksys,whw03)
emmc_copy_config
;;
esac
diff --git a/target/linux/ipq40xx/files-6.6/arch/arm/boot/dts/qcom/qcom-ipq4019-whw03.dts b/target/linux/ipq40xx/files-6.6/arch/arm/boot/dts/qcom/qcom-ipq4019-whw03.dts
new file mode 100644
index 0000000000..c835a2216e
--- /dev/null
+++ b/target/linux/ipq40xx/files-6.6/arch/arm/boot/dts/qcom/qcom-ipq4019-whw03.dts
@@ -0,0 +1,351 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Linksys WHW03 (Velop)";
+ compatible = "linksys,whw03", "qcom,ipq4019";
+
+ aliases {
+ led-boot = &led_blue;
+ led-failsafe = &led_red;
+ led-running = &led_blue;
+ led-upgrade = &led_red;
+ };
+
+ // Default bootargs include rootfstype=ext4 and need to be overriden.
+ chosen {
+ bootargs-append = " rootfstype=squashfs";
+ };
+
+ soc {
+ ess-tcsr at 1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+
+ tcsr at 1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr at 194b000 {
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ };
+
+ tcsr at 1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+ };
+
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+};
+
+
+&tlmm {
+ mdio_pins: mdio-pinmux {
+ mux-1 {
+ pins = "gpio6";
+ function = "mdio";
+ bias-pull-up;
+ };
+
+ mux-2 {
+ pins = "gpio7";
+ function = "mdc";
+ bias-pull-up;
+ };
+ };
+
+ sd_pins: sd-pinmux {
+ pins = "gpio23", "gpio24", "gpio25", "gpio26",
+ "gpio27", "gpio28", "gpio29", "gpio30",
+ "gpio31", "gpio32";
+ function = "sdio";
+ };
+
+ i2c_0_pins: i2c-0-pinmux {
+ pins = "gpio58", "gpio59";
+ function = "blsp_i2c0";
+ bias-disable;
+ };
+
+ serial_0_pins: serial0-pinmux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+
+ serial_1_pins: serial1-pinmux {
+ pins = "gpio8", "gpio9", "gpio10", "gpio11";
+ function = "blsp_uart1";
+ bias-disable;
+ };
+
+ spi_0_pins: spi-0-pinmux {
+ pins = "gpio12", "gpio13", "gpio14", "gpio15";
+ function = "blsp_spi0";
+ bias-disable;
+ };
+
+ spi_1_pins: spi-1-pinmux {
+ mux-1 {
+ pins = "gpio44", "gpio46", "gpio47";
+ function = "blsp_spi1";
+ bias-disable;
+ };
+
+ mux-2 {
+ pins = "gpio45", "gpio49";
+ function = "gpio";
+ bias-pull-up;
+ output-high;
+ };
+
+ host-interrupt {
+ pins = "gpio42";
+ function = "gpio";
+ input;
+ };
+ };
+
+ wifi_0_pins: wifi0-pinmux {
+ pins = "gpio52";
+ function = "gpio";
+ drive-strength = <6>;
+ bias-pull-up;
+ output-high;
+ };
+
+ zigbee-0 {
+ gpio-hog;
+ gpios = <29 GPIO_ACTIVE_HIGH>;
+ bias-disable;
+ output-low;
+ };
+
+ zigbee-1 {
+ gpio-hog;
+ gpios = <50 GPIO_ACTIVE_HIGH>;
+ bias-disable;
+ input;
+ };
+
+ bluetooth-enable {
+ gpio-hog;
+ gpios = <32 GPIO_ACTIVE_HIGH>;
+ output-high;
+ };
+};
+
+&mdio {
+ status = "okay";
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ reset-gpios = <&tlmm 41 GPIO_ACTIVE_LOW>;
+};
+
+ðphy0 {
+ status = "disabled";
+};
+
+ðphy1 {
+ status = "disabled";
+};
+
+ðphy2 {
+ status = "disabled";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+&prng {
+ status = "okay";
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&cryptobam {
+ num-channels = <4>;
+ qcom,num-ees = <2>;
+
+ status = "okay";
+};
+
+&crypto {
+ status = "okay";
+};
+
+&vqmmc {
+ status = "okay";
+};
+
+&blsp1_uart1 {
+ status = "okay";
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+};
+
+&blsp1_uart2 {
+ status = "okay";
+ pinctrl-0 = <&serial_1_pins>;
+ pinctrl-names = "default";
+
+ bluetooth {
+ compatible = "csr,8811";
+
+ enable-gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&blsp1_spi2 {
+ pinctrl-0 = <&spi_1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ cs-gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
+
+ zigbee at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ compatible = "silabs,em3581";
+ reg = <0>;
+ spi-max-frequency = <12000000>;
+ };
+};
+
+&blsp1_i2c3 {
+ pinctrl-0 = <&i2c_0_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+
+ // RGB LEDs
+ pca9633: led-controller at 62 {
+ compatible = "nxp,pca9633";
+ nxp,hw-blink;
+ reg = <0x62>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led_red: red at 0 {
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_INDICATOR;
+ reg = <0>;
+ };
+
+ led_green: green at 1 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_INDICATOR;
+ reg = <1>;
+ };
+
+ led_blue: blue at 2 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_INDICATOR;
+ reg = <2>;
+ };
+ };
+};
+
+&sdhci {
+ vqmmc-supply = <&vqmmc>;
+ pinctrl-0 = <&sd_pins>;
+ pinctrl-names = "default";
+ cd-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>;
+ sd-ldo-gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+
+ perst-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 40 GPIO_ACTIVE_LOW>;
+ clkreq-gpios = <&tlmm 39 GPIO_ACTIVE_LOW>;
+
+ bridge at 0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi2: wifi at 1,0 {
+ compatible = "qcom,ath10k";
+ reg = <0x00000000 0 0 0 0>;
+ };
+ };
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&gmac {
+ status = "okay";
+};
+
+&switch {
+ status = "okay";
+};
+
+&swport4 {
+ status = "okay";
+ label = "lan";
+};
+
+&swport5 {
+ status = "okay";
+ label = "wan";
+};
+
+&wifi0 {
+ pinctrl-0 = <&wifi_0_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+
+ qcom,coexist-support = <1>;
+ qcom,coexist-gpio-pin = <52>;
+
+ qcom,ath10k-calibration-variant = "linksys-whw03";
+};
+
+&wifi1 {
+ status = "okay";
+
+ ieee80211-freq-limit = <5170000 5330000>;
+ qcom,ath10k-calibration-variant = "linksys-whw03";
+};
+
+&wifi2 {
+ status = "okay";
+
+ ieee80211-freq-limit = <5490000 5835000>;
+ qcom,ath10k-calibration-variant = "linksys-whw03";
+};
diff --git a/target/linux/ipq40xx/image/generic.mk b/target/linux/ipq40xx/image/generic.mk
index 3b6d111905..7af777248d 100644
--- a/target/linux/ipq40xx/image/generic.mk
+++ b/target/linux/ipq40xx/image/generic.mk
@@ -723,6 +723,20 @@ define Device/linksys_mr8300
endef
TARGET_DEVICES += linksys_mr8300
+define Device/linksys_whw03
+ $(call Device/FitzImage)
+ DEVICE_VENDOR := Linksys
+ DEVICE_MODEL := WHW03
+ SOC := qcom-ipq4019
+ KERNEL_SIZE := 8192k
+ IMAGE_SIZE := 131072k
+ IMAGES += factory.bin
+ IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | linksys-image type=WHW03
+ DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-leds-pca963x kmod-spi-dev kmod-bluetooth \
+ kmod-fs-ext4 e2fsprogs kmod-fs-f2fs mkf2fs losetup
+endef
+TARGET_DEVICES += linksys_whw03
+
define Device/linksys_whw03v2
$(call Device/FitzImage)
DEVICE_VENDOR := Linksys
More information about the lede-commits
mailing list