[openwrt/openwrt] mediatek: add support for Routerich AX3000
LEDE Commits
lede-commits at lists.infradead.org
Thu Jan 4 12:49:03 PST 2024
hauke pushed a commit to openwrt/openwrt.git, branch openwrt-23.05:
https://git.openwrt.org/51881b2eb910d4adc6109b8d5abf0b23635a92ff
commit 51881b2eb910d4adc6109b8d5abf0b23635a92ff
Author: Mikhail Zhilkin <csharper2005 at gmail.com>
AuthorDate: Sat Dec 9 17:17:02 2023 +0000
mediatek: add support for Routerich AX3000
This PR is continuation of work under "mediatek: add support for Routerich
AX3000" #13703 by the agreement with PR #13703 original author (Maximilian
Weinmann <x1 at disroot.org>). All reviews from the previous PR were taken
into into account.
Routerich AX3000 is a wireless WiFi 6 router.
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz
- RAM : DDR3 256 MiB (ESMT M15T2G16128A)
- Flash : SPI-NAND 128 MiB (ESMT F50L1G41LB)
- WLAN : MediaTek MT7976CN dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x4 (MediaTek MT7531AE)
- USB : 1x 2.0
- UART : through-hole on PCB
- [J500] GND, TX, RX, 3.3V (115200n8)
- Buttons : Mesh, Reset
- LEDs : 1x Power (Blue)
1x WiFi 2.4 GHz (Blue)
1x WiFi 5 GHz (Red)
1x Mesh (Blue)
3x LAN activity (Blue)
1x WAN activity (Blue)
2x WAN no-internet (Red)
- Power : 12 VDC, 1.5 A
Installation
------------
Flash OpenWrt 'sysupgrade.bin' image using stock firmware web-interface
(without keeping settings).
Return to stock
---------------
Install stock firmware image (without keeping settings) using OpenWrt
sysupgrade method.
Recovery
--------
Connect uart, use u-boot menu to flash stock firmware image or boot
OpenWrt initramfs image.
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 24:0f:5e:xx:xx:b4 | label |
| LAN | 24:0f:5e:xx:xx:b5 | label+1 |
| WLAN 2g | 24:0f:5e:xx:xx:b6 | label+2 |
| WLAN 5g | 24:0f:5e:xx:xx:b7 | label+3 |
+---------+-------------------+-----------+
The WLAN 2g MAC was found in 'Factory', 0x4
Co-authored-by: Maximilian Weinmann <x1 at disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005 at gmail.com>
(cherry picked from commit 485adc9d3c436d31f9713a7d8d84adf266754e26)
[Fix merge conflict in uboot-envtools]
Signed-off-by: Mikhail Zhilkin <csharper2005 at gmail.com>
---
package/boot/uboot-envtools/files/mediatek_filogic | 3 +-
.../mediatek/dts/mt7981b-routerich-ax3000.dts | 337 +++++++++++++++++++++
.../filogic/base-files/etc/board.d/01_leds | 7 +
.../filogic/base-files/etc/board.d/02_network | 3 +-
.../etc/hotplug.d/ieee80211/11_fix_wifi_mac | 1 +
target/linux/mediatek/image/filogic.mk | 11 +
6 files changed, 360 insertions(+), 2 deletions(-)
diff --git a/package/boot/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-envtools/files/mediatek_filogic
index 8c7c5a85c0..b3113d683c 100644
--- a/package/boot/uboot-envtools/files/mediatek_filogic
+++ b/package/boot/uboot-envtools/files/mediatek_filogic
@@ -61,7 +61,8 @@ glinet,gl-mt6000)
local envdev=$(find_mmc_part "u-boot-env")
ubootenv_add_uci_config "$envdev" "0x0" "0x80000"
;;
-mercusys,mr90x-v1)
+mercusys,mr90x-v1|\
+routerich,ax3000)
local envdev=/dev/mtd$(find_mtd_index "u-boot-env")
ubootenv_add_uci_config "$envdev" "0x0" "0x20000" "0x20000" "1"
;;
diff --git a/target/linux/mediatek/dts/mt7981b-routerich-ax3000.dts b/target/linux/mediatek/dts/mt7981b-routerich-ax3000.dts
new file mode 100644
index 0000000000..1dc4d380b8
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7981b-routerich-ax3000.dts
@@ -0,0 +1,337 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+#include "mt7981.dtsi"
+
+/ {
+ model = "Routerich AX3000";
+ compatible = "routerich,ax3000", "mediatek,mt7981";
+
+ aliases {
+ label-mac-device = &wan;
+
+ led-boot = &led_power_blue;
+ led-failsafe = &led_power_blue;
+ led-running = &led_power_blue;
+ led-upgrade = &led_power_blue;
+
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ button-0 {
+ label = "mesh";
+ linux,input-type = <EV_SW>;
+ linux,code = <BTN_0>;
+ gpios = <&pio 0 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+
+ button-1 {
+ label = "reset";
+ gpios = <&pio 1 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ debounce-interval = <60>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_WLAN;
+ function-enumerator = <50>;
+ gpios = <&pio 5 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ led-1 {
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_WAN;
+ gpios = <&pio 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_power_blue: led-2 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_POWER;
+ gpios = <&pio 7 GPIO_ACTIVE_LOW>;
+ };
+
+ led-3 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <1>;
+ gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+ };
+
+ led-4 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <2>;
+ gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+ };
+
+ led-5 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <3>;
+ gpios = <&pio 11 GPIO_ACTIVE_LOW>;
+ };
+
+ led-6 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_WAN;
+ gpios = <&pio 12 GPIO_ACTIVE_LOW>;
+ };
+
+ led-7 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_WLAN;
+ function-enumerator = <24>;
+ gpios = <&pio 34 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ led-8 {
+ color = <LED_COLOR_ID_BLUE>;
+ /* LED_FUNCTION_MESH isn't implemented yet */
+ function = "mesh";
+ gpios = <&pio 35 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ memory {
+ reg = <0 0x40000000 0 0x10000000>;
+ };
+};
+
+ð {
+ status = "okay";
+
+ gmac0: mac at 0 {
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+ phy-mode = "2500base-x";
+
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_factory_4 (-1)>;
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+};
+
+&mdio_bus {
+ switch: switch at 1f {
+ compatible = "mediatek,mt7531";
+ reg = <0x1f>;
+ reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&pio>;
+ interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
+ };
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_flash_pins>;
+ status = "okay";
+
+ /* ESMT F50L1G41LB (128M) */
+ spi_nand at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-nand";
+ reg = <0>;
+
+ spi-max-frequency = <52000000>;
+ spi-tx-buswidth = <4>;
+ spi-rx-buswidth = <4>;
+
+ spi-cal-enable;
+ spi-cal-mode = "read-data";
+ spi-cal-datalen = <7>;
+ spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4e 0x41 0x4e 0x44>;
+ spi-cal-addrlen = <5>;
+ spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
+
+ mediatek,nmbm;
+ mediatek,bmt-max-ratio = <1>;
+ mediatek,bmt-max-reserved-blocks = <64>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0_all {
+ label = "spi0.0";
+ reg = <0x0 0x8000000>;
+ read-only;
+ };
+
+ partition at 0 {
+ label = "BL2";
+ reg = <0x0 0x100000>;
+ read-only;
+ };
+
+ partition at 100000 {
+ label = "u-boot-env";
+ reg = <0x100000 0x80000>;
+ };
+
+ partition at 180000 {
+ label = "Factory";
+ reg = <0x180000 0x200000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ eeprom_factory_0: eeprom at 0 {
+ reg = <0x0 0x1000>;
+ };
+
+ macaddr_factory_4: macaddr at 4 {
+ compatible = "mac-base";
+ reg = <0x4 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+ };
+ };
+
+ partition at 380000 {
+ label = "FIP";
+ reg = <0x380000 0x200000>;
+ read-only;
+ };
+
+ partition at 580000 {
+ label = "ubi";
+ reg = <0x580000 0x4000000>;
+ };
+
+ partition at 4580000 {
+ label = "firmware_backup";
+ reg = <0x4580000 0x2000000>;
+ read-only;
+ };
+
+ partition at 6580000 {
+ label = "zrsave";
+ reg = <0x6580000 0x100000>;
+ read-only;
+ };
+
+ partition at 6680000 {
+ label = "config2";
+ reg = <0x6680000 0x100000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&switch {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ label = "lan1";
+ };
+
+ port at 2 {
+ reg = <2>;
+ label = "lan2";
+ };
+
+ port at 3 {
+ reg = <3>;
+ label = "lan3";
+ };
+
+ wan: port at 4 {
+ reg = <4>;
+ label = "wan";
+
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_factory_4 (-2)>;
+ };
+
+ port at 6 {
+ reg = <6>;
+ ethernet = <&gmac0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+};
+
+&pio {
+ spi0_flash_pins: spi0-pins {
+ mux {
+ function = "spi";
+ groups = "spi0", "spi0_wp_hold";
+ };
+
+ conf-pu {
+ pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
+ };
+
+ conf-pd {
+ pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+&wifi {
+ status = "okay";
+ nvmem-cell-names = "eeprom";
+ nvmem-cells = <&eeprom_factory_0>;
+};
+
+&xhci {
+ status = "okay";
+ mediatek,u3p-dis-msk = <0x1>;
+};
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
index 546b7f6cd7..cdeaa6c5c5 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
@@ -26,6 +26,13 @@ netgear,wax220)
ucidef_set_led_netdev "wlan2g" "WLAN2G" "blue:wlan2g" "phy0-ap0"
ucidef_set_led_netdev "wlan5g" "WLAN5G" "blue:wlan5g" "phy1-ap0"
;;
+routerich,ax3000)
+ ucidef_set_led_netdev "lan-1" "lan-1" "blue:lan-1" "lan1" "link tx rx"
+ ucidef_set_led_netdev "lan-2" "lan-2" "blue:lan-2" "lan2" "link tx rx"
+ ucidef_set_led_netdev "lan-3" "lan-3" "blue:lan-3" "lan3" "link tx rx"
+ ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan" "link tx rx"
+ ucidef_set_led_netdev "wan-off" "wan-off" "red:wan" "wan" "link"
+ ;;
xiaomi,mi-router-wr30u-112m-nmbm|\
xiaomi,mi-router-wr30u-stock|\
xiaomi,mi-router-wr30u-ubootmod)
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
index a53b66f7cb..20a78b7b4b 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
@@ -29,7 +29,8 @@ mediatek_setup_interfaces()
confiabits,mt7981|\
cudy,wr3000-v1|\
jcg,q30-pro|\
- qihoo,360t7)
+ qihoo,360t7|\
+ routerich,ax3000)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" wan
;;
cmcc,rax3000m|\
diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
index b2b4f377a6..4911d5e85e 100644
--- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
+++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
@@ -95,6 +95,7 @@ case "$board" in
[ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress
[ "$PHYNBR" = "1" ] && macaddr_add $addr 1 > /sys${DEVPATH}/macaddress
;;
+ routerich,ax3000|\
zbtlink,zbt-z8102ax|\
zyxel,ex5601-t0)
addr=$(mtd_get_mac_binary "Factory" 0x4)
diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
index 95bc760d36..add838c4bc 100644
--- a/target/linux/mediatek/image/filogic.mk
+++ b/target/linux/mediatek/image/filogic.mk
@@ -600,6 +600,17 @@ define Device/qihoo_360t7
endef
TARGET_DEVICES += qihoo_360t7
+define Device/routerich_ax3000
+ DEVICE_VENDOR := Routerich
+ DEVICE_MODEL := AX3000
+ DEVICE_DTS := mt7981b-routerich-ax3000
+ DEVICE_DTS_DIR := ../dts
+ DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware kmod-usb3
+ IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+ SUPPORTED_DEVICES += mediatek,mt7981-spim-snand-rfb
+endef
+TARGET_DEVICES += routerich_ax3000
+
define Device/tplink_tl-xdr-common
DEVICE_VENDOR := TP-Link
DEVICE_DTS_DIR := ../dts
More information about the lede-commits
mailing list