[openwrt/openwrt] ath79: add support for KuWfi CPE830(D) / YunCore CPE830(D)
LEDE Commits
lede-commits at lists.infradead.org
Thu Dec 26 06:21:52 PST 2024
hauke pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/df222e57be467eb85e77f4f569e169d471c8ba54
commit df222e57be467eb85e77f4f569e169d471c8ba54
Author: Joan Moreau <jom at grosjo.net>
AuthorDate: Sat Sep 28 13:53:02 2024 +0000
ath79: add support for KuWfi CPE830(D) / YunCore CPE830(D)
Short specification:
* 650/600/216 MHz (CPU/DDR/AHB)
* 2x 10/100 Mbps Ethernet, passive PoE support
* 64 MB of RAM (DDR2)
* 16 MB of FLASH
* 2T2R 2.4 GHz with external PA, up to 30 dBm (1000mW)
* 2x internal 14 dBi antennas
* 8x LED, 1x button
* No UART on PCB on some versions
* Display panel with 2x buttons (F/N) not supported (and not relevant in OpenWrt)-
Flash instructions
* Connect PC with 192.168.0.141 to WAN port
* Install a TFTP server on your PC ('atftp' is doing the job for instance)
* Copy your firmware in the TFTP folder as upgrade.bin
* Power up device pushing the 'reset' button
* The device shall upload upgrade.bin, install it and reboot
* Device shall be booting on 192.168.1.1 as default
Signed-off-by: Joan Moreau <jom at grosjo.net>
Link: https://github.com/openwrt/openwrt/pull/17279
Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
---
target/linux/ath79/dts/qca9533_yuncore_cpe830.dts | 153 +++++++++++++++++++++
.../ath79/generic/base-files/etc/board.d/01_leds | 7 +
target/linux/ath79/image/generic.mk | 13 ++
3 files changed, 173 insertions(+)
diff --git a/target/linux/ath79/dts/qca9533_yuncore_cpe830.dts b/target/linux/ath79/dts/qca9533_yuncore_cpe830.dts
new file mode 100644
index 0000000000..31b0f2c610
--- /dev/null
+++ b/target/linux/ath79/dts/qca9533_yuncore_cpe830.dts
@@ -0,0 +1,153 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca953x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ compatible = "yuncore,cpe830", "qca,qca9533";
+ model = "YunCore/KuWfi CPE830(D)";
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ aliases {
+ label-mac-device = &wmac;
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ wlan {
+ function = LED_FUNCTION_WLAN;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ link1 {
+ label = "green:signal0";
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ link2 {
+ label = "green:signal1";
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ };
+
+ link3 {
+ label = "green:signal2";
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+ };
+
+ link4 {
+ label = "green:signal3";
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&spi {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "u-boot-env";
+ reg = <0x040000 0x010000>;
+ read-only;
+ };
+
+ partition at 50000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x050000 0xfa0000>;
+ };
+
+ partition at ff0000 {
+ label = "art";
+ reg = <0xff0000 0x010000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_art_0: macaddr at 0 {
+ reg = <0x0 0x6>;
+ };
+
+ macaddr_art_6: macaddr at 6 {
+ reg = <0x6 0x6>;
+ };
+
+ cal_art_1000: calibration at 1000 {
+ reg = <0x1000 0x440>;
+ };
+
+ macaddr_art_wmac: macaddr at 1002 {
+ reg = <0x1002 0x6>;
+ };
+ };
+ };
+ };
+ };
+};
+
+ð0 {
+ status = "okay";
+ phy-handle = <&swphy4>;
+ nvmem-cells = <&macaddr_art_0>;
+ nvmem-cell-names = "mac-address";
+};
+
+ð1 {
+ status = "okay";
+ nvmem-cells = <&macaddr_art_6>;
+ nvmem-cell-names = "mac-address";
+};
+
+&wmac {
+ status = "okay";
+ nvmem-cells = <&cal_art_1000>;
+ nvmem-cell-names = "calibration";
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index 6409adb78a..b9142c8a07 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -545,6 +545,13 @@ yuncore,a770)
ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth1"
ucidef_set_led_switch "lan" "LAN" "green:lan" "switch0" "0x10"
;;
+yuncore,cpe830)
+ ucidef_set_rssimon "wlan0" "200000" "1"
+ ucidef_set_led_rssi "wifi_low" "WIFILOW" "green:signal0" "wlan0" "1" "100"
+ ucidef_set_led_rssi "wifi_mediumlow" "WIFIMEDIUMLOW" "green:signal1" "wlan0" "26" "100"
+ ucidef_set_led_rssi "wifi_mediumhigh" "WIFIMEDIUMHIGH" "green:signal2" "wlan0" "51" "100"
+ ucidef_set_led_rssi "wifi_high" "WIFIHIGH" "green:signal3" "wlan0" "76" "100"
+ ;;
zbtlink,zbt-wd323)
ucidef_set_led_switch "lan1" "LAN1" "orange:lan1" "switch0" "0x10"
ucidef_set_led_switch "lan2" "LAN2" "orange:lan2" "switch0" "0x08"
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 846a9acd20..74ef0d2da0 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -3319,6 +3319,19 @@ define Device/yuncore_xd3200
endef
TARGET_DEVICES += yuncore_xd3200
+define Device/yuncore_cpe830
+ SOC := qca9533
+ DEVICE_VENDOR := YunCore
+ DEVICE_MODEL := CPE830(D)
+ DEVICE_ALT0_VENDOR = KuWfi
+ DEVICE_ALT0_MODEL = CPE830(D)
+ IMAGE_SIZE := 16000k
+ IMAGES += tftp.bin
+ IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
+ DEVICE_PACKAGES := rssileds -swconfig
+endef
+TARGET_DEVICES += yuncore_cpe830
+
define Device/yuncore_xd4200
SOC := qca9563
DEVICE_VENDOR := YunCore
More information about the lede-commits
mailing list