[openwrt/openwrt] mediatek/filogic: add Keenetic KN-3811 support
LEDE Commits
lede-commits at lists.infradead.org
Sun Dec 8 10:54:20 PST 2024
hauke pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/d087a79b7b03fe93a221fd6246ce437c5c5325c3
commit d087a79b7b03fe93a221fd6246ce437c5c5325c3
Author: Maxim Anisimov <maxim.anisimov.ua at gmail.com>
AuthorDate: Wed Nov 13 17:17:17 2024 +0300
mediatek/filogic: add Keenetic KN-3811 support
Specification:
* Mediatek MT7981BA
* 256 MB SPI-NAND
* 512 MB DDR4 RAM
* MT7976CN DBDC AX Wi-Fi
* MediaTek MT7531AE (3x LAN Gigabit ports) + Internal Gbe Phy (1x WAN Gigabit port)
* 4x LED (power, internet, fn, wifi)
* 3x buttons (wps, fn, reset)
* 1x USB 3.0 port
Serial Interface:
* 3 Pins GND, RX, TX
* Settings: 115200, 8N1
Notes:
* The device supports dual boot mode
* Fn led reassigned to wlan 2.4
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-mediatek-filogic-keenetic_kn-3811-squashfs-factory.bin"
to "KN-3811_recovery.bin" and place it in tftp server directory.
3. Connect PC with ethernet port, press the reset button, power up
the device and keep button pressed until status led start blinking.
4. Device will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua at gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17135
Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
---
.../mediatek/dts/mt7981b-keenetic-kn-3811.dts | 368 +++++++++++++++++++++
.../filogic/base-files/etc/board.d/02_network | 1 +
.../etc/hotplug.d/ieee80211/11_fix_wifi_mac | 1 +
target/linux/mediatek/image/filogic.mk | 20 ++
4 files changed, 390 insertions(+)
diff --git a/target/linux/mediatek/dts/mt7981b-keenetic-kn-3811.dts b/target/linux/mediatek/dts/mt7981b-keenetic-kn-3811.dts
new file mode 100644
index 0000000000..87043ec907
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7981b-keenetic-kn-3811.dts
@@ -0,0 +1,368 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+
+/dts-v1/;
+
+#include "mt7981.dtsi"
+
+/ {
+ model = "Keenetic KN-3811";
+ compatible = "keenetic,kn-3811", "mediatek,mt7981";
+
+ aliases {
+ label-mac-device = &gmac0;
+ led-boot = &power_led;
+ led-failsafe = &power_led;
+ led-running = &power_led;
+ led-upgrade = &power_led;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ button-fn {
+ label = "fn";
+ linux,code = <BTN_0>;
+ gpios = <&pio 5 GPIO_ACTIVE_LOW>;
+ };
+
+ button-reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&pio 24 GPIO_ACTIVE_LOW>;
+ };
+
+ button-wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&pio 29 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ /* fn led reassigned to wlan 2.4 */
+ led-0 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_WLAN_2GHZ;
+ gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ power_led: led-1 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_POWER;
+ gpios = <&pio 11 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-2 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_WAN;
+ gpios = <&pio 12 GPIO_ACTIVE_LOW>;
+ };
+
+ led-3 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_WLAN_5GHZ;
+ gpios = <&pio 34 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+ };
+
+ usb_vbus: regulator-usb-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpios = <&pio 6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
+ virtual_flash {
+ compatible = "mtd-concat";
+ devices = <&firmware1 &storage1 &firmware2 &storage2>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "kernel";
+ reg = <0x0 0x600000>;
+ };
+
+ partition at 400000 {
+ label = "ubi";
+ reg = <0x600000 0x0>;
+ };
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+ð {
+ status = "okay";
+
+ gmac0: mac at 0 {
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+ phy-mode = "2500base-x";
+
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_factory_4 0>;
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+
+ gmac1: mac at 1 {
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+ phy-mode = "gmii";
+ phy-handle = <&int_gbe_phy>;
+ label = "wan";
+
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_factory_a 0>;
+ };
+};
+
+&mdio_bus {
+ switch: switch at 1f {
+ compatible = "mediatek,mt7531";
+ reg = <0x1f>;
+ reset-gpios = <&pio 22 GPIO_ACTIVE_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&pio>;
+ interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
+ };
+};
+
+&switch {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ label = "lan1";
+ };
+
+ port at 1 {
+ reg = <1>;
+ label = "lan2";
+ };
+
+ port at 2 {
+ reg = <2>;
+ label = "lan3";
+ };
+
+ port at 6 {
+ reg = <6>;
+ ethernet = <&gmac0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+};
+
+&pio {
+ spi0_flash_pins: spi0-pins {
+ mux {
+ function = "spi";
+ groups = "spi0", "spi0_wp_hold";
+ };
+
+ conf-pu {
+ pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
+ };
+
+ conf-pd {
+ pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
+ };
+ };
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_flash_pins>;
+ status = "okay";
+
+ /* Winbond W25N02KV (256M) */
+ spi_nand at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-nand";
+ reg = <0>;
+
+ spi-max-frequency = <52000000>;
+ spi-tx-buswidth = <4>;
+ spi-rx-buswidth = <4>;
+
+ spi-cal-enable;
+ spi-cal-mode = "read-data";
+ spi-cal-datalen = <7>;
+ spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4e 0x41 0x4e 0x44>;
+ spi-cal-addrlen = <5>;
+ spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
+
+ mediatek,nmbm;
+ mediatek,bmt-max-ratio = <1>;
+ mediatek,bmt-max-reserved-blocks = <64>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* bl2 */
+ partition at 0 {
+ label = "preloader";
+ reg = <0x0 0x80000>;
+ read-only;
+ };
+
+ /* fip */
+ partition at 80000 {
+ label = "u-boot";
+ reg = <0x80000 0x200000>;
+ read-only;
+ };
+
+ partition at 280000 {
+ label = "u-config";
+ reg = <0x280000 0x80000>;
+ read-only;
+ };
+
+ partition at 300000 {
+ label = "rf-eeprom";
+ reg = <0x300000 0x200000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ eeprom_factory_0: eeprom at 0 {
+ reg = <0x0 0x1000>;
+ };
+
+ /* lan mac */
+ macaddr_factory_4: macaddr at 4 {
+ compatible = "mac-base";
+ reg = <0x4 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ /* wan mac */
+ macaddr_factory_a: macaddr at a {
+ compatible = "mac-base";
+ reg = <0xa 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+ };
+ };
+
+ firmware1: partition at 500000 {
+ label = "firmware_1";
+ reg = <0x500000 0x3a00000>;
+ };
+
+ partition at 3f00000 {
+ label = "config_1";
+ reg = <0x3f00000 0x80000>;
+ read-only;
+ };
+
+ partition at 3f80000 {
+ label = "dump";
+ reg = <0x3f80000 0x80000>;
+ read-only;
+ };
+
+ storage1: partition at 4000000 {
+ label = "storage_a";
+ reg = <0x4000000 0x3800000>;
+ };
+
+ partition at 7800000 {
+ label = "u-state";
+ reg = <0x7800000 0x20000>;
+ read-only;
+ };
+
+ partition at 7a80000 {
+ label = "u-config_res";
+ reg = <0x7a80000 0x80000>;
+ read-only;
+ };
+
+ partition at 7b00000 {
+ label = "rf-eeprom_res";
+ reg = <0x7b00000 0x200000>;
+ read-only;
+ };
+
+ firmware2: partition at 7d00000 {
+ label = "firmware_2";
+ reg = <0x7d00000 0x3a00000>;
+ };
+
+ partition at b700000 {
+ label = "config_2";
+ reg = <0xb700000 0x80000>;
+ read-only;
+ };
+
+ storage2: partition at b780000 {
+ label = "storage_b";
+ reg = <0xb780000 0x3880000>;
+ };
+ };
+ };
+};
+
+&wifi {
+ nvmem-cell-names = "eeprom";
+ nvmem-cells = <&eeprom_factory_0>;
+ status = "okay";
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&xhci {
+ status = "okay";
+ vbus-supply = <&usb_vbus>;
+};
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
index ba78564402..78483442d7 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
@@ -33,6 +33,7 @@ mediatek_setup_interfaces()
confiabits,mt7981|\
cudy,wr3000-v1|\
jcg,q30-pro|\
+ keenetic,kn-3811|\
qihoo,360t7|\
routerich,ax3000|\
routerich,ax3000-ubootmod)
diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
index a3b7671223..fb67323e7b 100644
--- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
+++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
@@ -115,6 +115,7 @@ case "$board" in
jdcloud,re-cp-03)
[ "$PHYNBR" = "1" ] && mmc_get_mac_binary factory 0xa > /sys${DEVPATH}/macaddress
;;
+ keenetic,kn-3811|\
keenetic,kn-3911)
[ "$PHYNBR" = "1" ] && \
macaddr_setbit_la "$(mtd_get_mac_binary rf-eeprom 0x4)" > /sys${DEVPATH}/macaddress
diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
index 5498922f6e..c1b38403a6 100644
--- a/target/linux/mediatek/image/filogic.mk
+++ b/target/linux/mediatek/image/filogic.mk
@@ -887,6 +887,26 @@ define Device/jdcloud_re-cp-03
endef
TARGET_DEVICES += jdcloud_re-cp-03
+define Device/keenetic_kn-3811
+ DEVICE_VENDOR := Keenetic
+ DEVICE_MODEL := KN-3811
+ DEVICE_DTS := mt7981b-keenetic-kn-3811
+ DEVICE_DTS_DIR := ../dts
+ DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware kmod-usb3
+ UBINIZE_OPTS := -E 5
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ KERNEL_SIZE := 6144k
+ IMAGE_SIZE := 233984k
+ KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | \
+ append-squashfs4-fakeroot
+ IMAGES += factory.bin
+ IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | \
+ append-ubi | check-size | zyimage -d 0x803811 -v "KN-3811"
+ IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+endef
+TARGET_DEVICES += keenetic_kn-3811
+
define Device/keenetic_kn-3911
DEVICE_VENDOR := Keenetic
DEVICE_MODEL := KN-3911
More information about the lede-commits
mailing list