[openwrt/openwrt] qualcommax: ipq60xx: add Linksys MR7350 support
LEDE Commits
lede-commits at lists.infradead.org
Sat Dec 7 07:01:04 PST 2024
robimarko pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/9c55866fada91c45679f75d03e6d13e1e0cd4202
commit 9c55866fada91c45679f75d03e6d13e1e0cd4202
Author: Vladyslav Andreichykov <vladdrako007 at gmail.com>
AuthorDate: Thu Mar 7 11:47:04 2024 +0200
qualcommax: ipq60xx: add Linksys MR7350 support
Linksys MR7350 is a 802.11ax Dual-band router/AP.
Specifications:
* CPU: Qualcomm IPQ6000 Quad core Cortex-A53(A73) 1.5GHz
* RAM: 512MB of DDR3
* Storage: 256Mb NAND
* Ethernet: 5x1G RJ45 ports (QCA8075)
* WLAN:
* 2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5052 2x2 at 80MHz or 802.11a/b/g/n/ac/ax 1201 Mbps PHY rate
* LED-s:
* RGB system led
* USB blue led
* Buttons: 1x Soft reset 1x WPS
* Power: 12V DC Jack
Installation instructions:
Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup.
Login with your admin password. The default password can be found on a sticker under the device.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device.
Then you would need to write openwrt to the other partition for it to work
- First Check booted partition:
fw_printenv -n boot_part
- Change the partition:
fw_setenv boot_part 1
or
fw_setenv boot_part 2
depending on the current partition
- Then install Openwrt to the other partition if booted in slot 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin alt_kernel
- If in slot 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin kernel
Co-Authored-by: Chukun Pan <amadeus at jmu.edu.cn>
Co-Authored-by: Robert Marko <robimarko at gmail.com>
Signed-off-by: Vladyslav Andreichykov <vladdrako007 at gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14807
Signed-off-by: Robert Marko <robimarko at gmail.com>
---
.../boot/uboot-envtools/files/qualcommax_ipq60xx | 5 +
package/firmware/ipq-wifi/Makefile | 2 +
.../arch/arm64/boot/dts/qcom/ipq6000-mr7350.dts | 465 +++++++++++++++++++++
target/linux/qualcommax/image/ipq60xx.mk | 18 +
.../ipq60xx/base-files/etc/board.d/01_leds | 12 +
.../ipq60xx/base-files/etc/board.d/02_network | 8 +-
.../etc/hotplug.d/firmware/11-ath11-caldata | 1 +
.../etc/hotplug.d/ieee80211/11_fix_wifi_mac | 18 +
.../ipq60xx/base-files/etc/init.d/bootcount | 3 +
.../ipq60xx/base-files/lib/upgrade/platform.sh | 14 +
10 files changed, 545 insertions(+), 1 deletion(-)
diff --git a/package/boot/uboot-envtools/files/qualcommax_ipq60xx b/package/boot/uboot-envtools/files/qualcommax_ipq60xx
index 853037b776..ccc74e2df6 100644
--- a/package/boot/uboot-envtools/files/qualcommax_ipq60xx
+++ b/package/boot/uboot-envtools/files/qualcommax_ipq60xx
@@ -15,6 +15,11 @@ cambiumnetworks,xe3-4)
[ -n "$idx" ] && \
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x10000" "0x10000"
;;
+linksys,mr7350)
+ idx="$(find_mtd_index u_env)"
+ [ -n "$idx" ] && \
+ ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2"
+ ;;
netgear,wax214)
idx="$(find_mtd_index 0:appsblenv)"
[ -n "$idx" ] && \
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile
index b80665efdb..fe17484d85 100644
--- a/package/firmware/ipq-wifi/Makefile
+++ b/package/firmware/ipq-wifi/Makefile
@@ -37,6 +37,7 @@ ALLWIFIBOARDS:= \
dynalink_dl-wrx36 \
edgecore_eap102 \
edimax_cax1800 \
+ linksys_mr7350 \
linksys_mx4200 \
linksys_mx5300 \
linksys_mx8500 \
@@ -165,6 +166,7 @@ $(eval $(call generate-ipq-wifi-package,compex_wpq873,Compex WPQ-873))
$(eval $(call generate-ipq-wifi-package,dynalink_dl-wrx36,Dynalink DL-WRX36))
$(eval $(call generate-ipq-wifi-package,edgecore_eap102,Edgecore EAP102))
$(eval $(call generate-ipq-wifi-package,edimax_cax1800,Edimax CAX1800))
+$(eval $(call generate-ipq-wifi-package,linksys_mr7350,Linksys MR7350))
$(eval $(call generate-ipq-wifi-package,linksys_mx4200,Linksys MX4200))
$(eval $(call generate-ipq-wifi-package,linksys_mx5300,Linksys MX5300))
$(eval $(call generate-ipq-wifi-package,linksys_mx8500,Linksys MX8500))
diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6000-mr7350.dts b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6000-mr7350.dts
new file mode 100644
index 0000000000..5761c3b582
--- /dev/null
+++ b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6000-mr7350.dts
@@ -0,0 +1,465 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include "ipq6018.dtsi"
+#include "ipq6018-cp-cpu.dtsi"
+#include "ipq6018-ess.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Linksys MR7350";
+ compatible = "linksys,mr7350", "qcom,ipq6018";
+
+ aliases {
+ serial0 = &blsp1_uart3;
+ serial1 = &blsp1_uart2;
+ led-boot = &led_system_blue;
+ led-running = &led_system_blue;
+ led-failsafe = &led_system_red;
+ led-upgrade = &led_system_green;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs-append = " root=/dev/ubiblock0_0";
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ wps-button {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&tlmm 56 GPIO_ACTIVE_LOW>;
+ };
+
+ reset-button {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&tlmm 57 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ /*lan1-amber {
+ label = "amber:lan1";
+ color = <LED_COLOR_ID_AMBER>;
+ gpios = <&qca8075_0 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ lan1-green {
+ label = "green:lan1";
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&qca8075_0 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ lan2-amber {
+ label = "amber:lan2";
+ color = <LED_COLOR_ID_AMBER>;
+ gpios = <&qca8075_1 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ lan2-green {
+ label = "green:lan2";
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&qca8075_1 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ lan3-amber {
+ label = "amber:lan3";
+ color = <LED_COLOR_ID_AMBER>;
+ gpios = <&qca8075_2 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ lan3-green {
+ label = "green:lan3";
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&qca8075_2 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ lan4-amber {
+ label = "amber:lan4";
+ color = <LED_COLOR_ID_AMBER>;
+ gpios = <&qca8075_3 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ lan4-green {
+ label = "green:lan4";
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&qca8075_3 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ wan-amber {
+ color = <LED_COLOR_ID_AMBER>;
+ function = LED_FUNCTION_WAN;
+ gpios = <&qca8075_4 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ wan-green {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_WAN;
+ gpios = <&qca8075_4 1 GPIO_ACTIVE_HIGH>;
+ };*/
+
+ usb {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_USB;
+ gpios = <&tlmm 60 GPIO_ACTIVE_HIGH>;
+ trigger-sources = <&usb3_port1>, <&usb3_port2>;
+ linux,default-trigger = "usbport";
+ };
+ };
+
+ reg_usb_vbus: regulator-usb-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&tlmm 61 GPIO_ACTIVE_LOW>;
+ regulator-boot-on;
+ };
+
+ output-usb0-power {
+ compatible = "regulator-output";
+ vout-supply = <®_usb_vbus>;
+ };
+};
+
+&tlmm {
+ hsuart_pins: hsuart-pins {
+ mux {
+ pins = "gpio69", "gpio70",
+ "gpio71", "gpio72";
+ function = "blsp1_uart";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ i2c_pins: i2c-pins {
+ mux {
+ pins = "gpio42", "gpio43";
+ function = "blsp2_i2c";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+ };
+
+ mdio_pins: mdio-state {
+ mdc-pins {
+ pins = "gpio64";
+ function = "mdc";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ mdio-pins {
+ pins = "gpio65";
+ function = "mdio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+};
+
+&blsp1_i2c3 {
+ pinctrl-0 = <&i2c_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ led-controller at 62 {
+ compatible = "nxp,pca9633";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x62>;
+
+ led_system_red: led at 0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_STATUS;
+ };
+
+ led_system_green: led at 1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ };
+
+ led_system_blue: led at 2 {
+ reg = <2>;
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_STATUS;
+ };
+ };
+};
+
+&blsp1_uart2 {
+ pinctrl-0 = <&hsuart_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&blsp1_uart3 {
+ pinctrl-0 = <&serial_3_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&dwc_0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb3_port1: port at 1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+
+ usb3_port2: port at 2 {
+ reg = <2>;
+ #trigger-source-cells = <0>;
+ };
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&qpic_nand {
+ status = "okay";
+
+ nand at 0 {
+ reg = <0>;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ nand-bus-width = <8>;
+
+ partitions {
+ compatible = "qcom,smem-part";
+ };
+ };
+};
+
+&qusb_phy_0 {
+ status = "okay";
+};
+
+&ssphy_0 {
+ status = "okay";
+};
+
+&usb3 {
+ vbus-supply = <®_usb_vbus>;
+ status = "okay";
+};
+
+&mdio {
+ status = "okay";
+
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ reset-gpios = <&tlmm 75 GPIO_ACTIVE_LOW>;
+
+ ethernet-phy-package at 0 {
+ compatible = "qcom,qca8075-package";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ qca8075_0: ethernet-phy at 0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led at 0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_ORANGE>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+
+ led at 1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+ };
+ };
+
+ qca8075_1: ethernet-phy at 1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led at 0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_ORANGE>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+
+ led at 1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+ };
+ };
+
+ qca8075_2: ethernet-phy at 2 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <2>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led at 0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_ORANGE>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+
+ led at 1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+ };
+ };
+
+ qca8075_3: ethernet-phy at 3 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <3>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led at 0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_ORANGE>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+
+ led at 1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+ };
+ };
+
+ qca8075_4: ethernet-phy at 4 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <4>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led at 0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_ORANGE>;
+ function = LED_FUNCTION_WAN;
+ default-state = "keep";
+ };
+
+ led at 1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_WAN;
+ default-state = "keep";
+ };
+ };
+ };
+ };
+};
+
+&switch {
+ status = "okay";
+
+ switch_lan_bmp = <(ESS_PORT1 | ESS_PORT2 | ESS_PORT3 | ESS_PORT4)>;
+ switch_wan_bmp = <ESS_PORT5>;
+ switch_mac_mode = <MAC_MODE_PSGMII>;
+
+ qcom,port_phyinfo {
+ port at 1 {
+ port_id = <1>;
+ phy_address = <0>;
+ };
+ port at 2 {
+ port_id = <2>;
+ phy_address = <1>;
+ };
+ port at 3 {
+ port_id = <3>;
+ phy_address = <2>;
+ };
+ port at 4 {
+ port_id = <4>;
+ phy_address = <3>;
+ };
+ port at 5 {
+ port_id = <5>;
+ phy_address = <4>;
+ };
+ };
+};
+
+&edma {
+ status = "okay";
+};
+
+&dp1 {
+ status = "okay";
+ phy-handle = <&qca8075_0>;
+ label = "lan1";
+};
+
+&dp2 {
+ status = "okay";
+ phy-handle = <&qca8075_1>;
+ label = "lan2";
+};
+
+&dp3 {
+ status = "okay";
+ phy-handle = <&qca8075_2>;
+ label = "lan3";
+};
+
+&dp4 {
+ status = "okay";
+ phy-handle = <&qca8075_3>;
+ label = "lan4";
+};
+
+&dp5 {
+ status = "okay";
+ phy-handle = <&qca8075_4>;
+ label = "wan";
+};
+
+&wifi {
+ status = "okay";
+
+ qcom,ath11k-calibration-variant = "Linksys-MR7350";
+ qcom,ath11k-fw-memory-mode = <1>;
+};
diff --git a/target/linux/qualcommax/image/ipq60xx.mk b/target/linux/qualcommax/image/ipq60xx.mk
index d861f82d1c..0b7cd413c3 100644
--- a/target/linux/qualcommax/image/ipq60xx.mk
+++ b/target/linux/qualcommax/image/ipq60xx.mk
@@ -24,6 +24,24 @@ define Device/cambiumnetworks_xe3-4
endef
TARGET_DEVICES += cambiumnetworks_xe3-4
+define Device/linksys_mr7350
+ $(call Device/FitImage)
+ DEVICE_VENDOR := Linksys
+ DEVICE_MODEL := MR7350
+ SOC := ipq6000
+ NAND_SIZE := 256m
+ KERNEL_SIZE := 8192k
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ IMAGE_SIZE := 75776k
+ IMAGES += factory.bin
+ IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
+ append-ubi | linksys-image type=MR7350
+ DEVICE_PACKAGES := ipq-wifi-linksys_mr7350 \
+ kmod-leds-pca963x kmod-usb-ledtrig-usbport
+endef
+TARGET_DEVICES += linksys_mr7350
+
define Device/netgear_wax214
$(call Device/FitImage)
$(call Device/UbiFit)
diff --git a/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/01_leds b/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/01_leds
index 189822157f..a9575eb4ef 100644
--- a/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/01_leds
+++ b/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/01_leds
@@ -7,6 +7,18 @@ board_config_update
board=$(board_name)
case "$board" in
+linksys,mr7350)
+ ucidef_set_led_netdev "lan1-port-link" "LAN1-PORT-LINK" "90000.mdio-1:00:green:lan" "lan1" "link_10 link_100 link_1000"
+ ucidef_set_led_netdev "lan1-port-traffic" "LAN1-PORT-TRAFFIC" "90000.mdio-1:00:orange:lan" "lan1" "tx rx link_10 link_100 link_1000"
+ ucidef_set_led_netdev "lan2-port-link" "LAN2-PORT-LINK" "90000.mdio-1:01:green:lan" "lan2" "link_10 link_100 link_1000"
+ ucidef_set_led_netdev "lan2-port-traffic" "LAN2-PORT-TRAFFIC" "90000.mdio-1:01:orange:lan" "lan2" "tx rx link_10 link_100 link_1000"
+ ucidef_set_led_netdev "lan3-port-link" "LAN3-PORT-LINK" "90000.mdio-1:02:green:lan" "lan3" "link_10 link_100 link_1000"
+ ucidef_set_led_netdev "lan3-port-traffic" "LAN3-PORT-TRAFFIC" "90000.mdio-1:02:orange:lan" "lan3" "tx rx link_10 link_100 link_1000"
+ ucidef_set_led_netdev "lan4-port-link" "LAN4-PORT-LINK" "90000.mdio-1:03:green:lan" "lan4" "link_10 link_100 link_1000"
+ ucidef_set_led_netdev "lan4-port-traffic" "LAN4-PORT-TRAFFIC" "90000.mdio-1:03:orange:lan" "lan4" "tx rx link_10 link_100 link_1000"
+ ucidef_set_led_netdev "wan-port-link" "WAN-PORT-LINK" "90000.mdio-1:04:green:wan" "wan" "link_10 link_100 link_1000"
+ ucidef_set_led_netdev "wan-port-traffic" "WAN-PORT-TRAFFIC" "90000.mdio-1:04:orange:wan" "wan" "tx rx link_10 link_100 link_1000"
+ ;;
yuncore,fap650)
ucidef_set_led_netdev "wlan5ghz" "WLAN 5GHz LED" "blue:wlan-5ghz" "wlan0" "tx rx"
ucidef_set_led_netdev "wlan2ghz" "WLAN 2.4GHz LED" "green:wlan-2ghz" "wlan1" "tx rx"
diff --git a/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network b/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network
index 86ed04f34b..ecc9e57117 100644
--- a/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network
+++ b/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network
@@ -23,6 +23,7 @@ ipq60xx_setup_interfaces()
qihoo,360v6)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan"
;;
+ linksys,mr7350|\
yuncore,fap650)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
;;
@@ -39,7 +40,12 @@ ipq60xx_setup_macs()
local wan_mac=""
local label_mac=""
- case "$board" in
+ case $board in
+ linksys,mr7350)
+ label_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
+ lan_mac=$label_mac
+ wan_mac=$label_mac
+ ;;
qihoo,360v6)
lan_mac=$(mtd_get_mac_ascii factory lanMac)
wan_mac=$(macaddr_add "$lan_mac" 1)
diff --git a/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11-caldata b/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11-caldata
index e35413e1e0..a5e843ee7b 100644
--- a/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11-caldata
+++ b/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11-caldata
@@ -15,6 +15,7 @@ case "$FIRMWARE" in
cambiumnetworks,xe3-4)
caldata_extract "0:ART" 0x1000 0x10000
;;
+ linksys,mr7350|\
netgear,wax214)
caldata_extract "0:art" 0x1000 0x10000
;;
diff --git a/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
new file mode 100644
index 0000000000..a67cc7262b
--- /dev/null
+++ b/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
@@ -0,0 +1,18 @@
+[ "$ACTION" == "add" ] || exit 0
+
+PHYNBR=${DEVPATH##*/phy}
+
+[ -n $PHYNBR ] || exit 0
+
+. /lib/functions.sh
+. /lib/functions/system.sh
+
+board=$(board_name)
+
+case "$board" in
+ linksys,mr7350)
+ addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
+ [ "$PHYNBR" = "0" ] && macaddr_add $addr 2 > /sys${DEVPATH}/macaddress
+ [ "$PHYNBR" = "1" ] && macaddr_add $addr 1 > /sys${DEVPATH}/macaddress
+ ;;
+esac
diff --git a/target/linux/qualcommax/ipq60xx/base-files/etc/init.d/bootcount b/target/linux/qualcommax/ipq60xx/base-files/etc/init.d/bootcount
old mode 100755
new mode 100644
index b34fbd82d7..e8ff90122b
--- a/target/linux/qualcommax/ipq60xx/base-files/etc/init.d/bootcount
+++ b/target/linux/qualcommax/ipq60xx/base-files/etc/init.d/bootcount
@@ -4,6 +4,9 @@ START=99
boot() {
case $(board_name) in
+ linksys,mr7350)
+ mtd resetbc s_env || true
+ ;;
yuncore,fap650)
fw_setenv owrt_bootcount 0
;;
diff --git a/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh b/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh
index c545746b31..411570715c 100644
--- a/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh
@@ -37,6 +37,20 @@ platform_do_upgrade() {
fw_setenv bootcount 0
nand_do_upgrade "$1"
;;
+ linksys,mr7350)
+ boot_part="$(fw_printenv -n boot_part)"
+ if [ "$boot_part" -eq "1" ]; then
+ fw_setenv boot_part 2
+ CI_KERNPART="alt_kernel"
+ CI_UBIPART="alt_rootfs"
+ else
+ fw_setenv boot_part 1
+ CI_UBIPART="rootfs"
+ fi
+ fw_setenv boot_part_ready 3
+ fw_setenv auto_recovery yes
+ nand_do_upgrade "$1"
+ ;;
netgear,wax214|\
qihoo,360v6)
nand_do_upgrade "$1"
More information about the lede-commits
mailing list