[openwrt/openwrt] mediatek: add support for Mercusys MR90X v1
LEDE Commits
lede-commits at lists.infradead.org
Sun Jun 25 03:28:08 PDT 2023
hauke pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/e4fe3097ef6a961874b66932a0ac4be18070630a
commit e4fe3097ef6a961874b66932a0ac4be18070630a
Author: Mikhail Zhilkin <csharper2005 at gmail.com>
AuthorDate: Sat May 13 13:51:45 2023 +0000
mediatek: add support for Mercusys MR90X v1
This commit adds support for Mercusys MR90X(EU) v1 router.
Device specification
--------------------
SoC Type: MediaTek MT7986BLA, Cortex-A53, 64-bit
RAM: MediaTek MT7986BLA (512MB)
Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB)
Ethernet: MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8)
Ethernet: 1x2.5Gbe (WAN/LAN 2.5Gbps), 3xGbE (WAN/LAN 1Gbps, LAN1, LAN2)
WLAN 2g: MediaTek MT7975N, b/g/n/ax, MIMO 4x4
WLAN 5g: MediaTek MT7975P(N), a/n/ac/ax, MIMO 4x4
LEDs: 1 orange and 1 green status LEDs, 4 green gpio-controlled
LEDs on ethernet ports
Button: 1 (Reset)
USB ports: No
Power: 12 VDC, 2 A
Connector: Barrel
Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI
slots contain "seconduboot" (also U-Boot 2022.01-rc4)
Serial console (UART)
---------------------
V
+-------+-------+-------+-------+
| +3.3V | GND | TX | RX |
+---+---+-------+-------+-------+
|
+--- Don't connect
The R3 (TX line) and R6 (RX line) are absent on the PCB. You should
solder them or solder the jumpers.
Installation (UART)
-------------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
tftpboot initramfs-kernel.bin
bootm
4. Once inside OpenWrt, set / update env variables:
fw_setenv baudrate 115200
fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit"
fw_setenv fdtcontroladdr 5ffc0e70
fw_setenv ipaddr 192.168.1.1
fw_setenv loadaddr 0x46000000
fw_setenv mtdids "spi-nand0=spi-nand0"
fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)"
fw_setenv netmask 255.255.255.0
fw_setenv serverip 192.168.1.2
fw_setenv stderr serial at 11002000
fw_setenv stdin serial at 11002000
fw_setenv stdout serial at 11002000
fw_setenv tp_boot_idx 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Installation (without UART)
---------------------------
1. Login as root via SSH (router IP, port 20001, password - your web
interface password)
2. Open for editing /etc/hotplug.d/iface/65-iptv (e.g., using WinSCP and
SSH settings from the p.1)
3. Add a newline after "#!/bin/sh":
telnetd -l /bin/login.sh
4. Save "65-iptv" file
5. Toggle "IPTV/VLAN Enable" checkbox in the router web interface and
save
6. Make sure that telnetd is running:
netstat -ltunp | grep 23
7. Login via telnet to router IP, port 23 (no username and password are
required)
8 Upload OpenWrt "initramfs-kernel.bin" to the "/tmp" folder of the
router (e.g., using WinSCP and SSH settings from the p.1)
9. Stock busybox doesn't contain ubiupdatevol command. Hence, we need to
download and upload the full version of busybox to the router. For
example, from here:
https://github.com/xerta555/Busybox-Binaries/raw/master/busybox-arm64
Upload busybox-arm64 to the /tmp dir of the router and run:
in the telnet shell:
cd /tmp
chmod a+x busybox-arm64
10. Check "initramfs-kernel.bin" size:
du -h initramfs-kernel.bin
11. Delete old and create new "kernel" volume with appropriate size
(greater than "initramfs-kernel.bin" size):
ubirmvol /dev/ubi0 -N kernel
ubimkvol /dev/ubi0 -n 1 -N kernel -s 9MiB
12. Write OpenWrt "initramfs-kernel.bin" to the flash:
./busybox-arm64 ubiupdatevol /dev/ubi0_1 /tmp/initramfs-kernel.bin
13. u-boot-env can be empty so lets create it (or overwrite it if it
already exists) with the necessary values:
fw_setenv baudrate 115200
fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit"
fw_setenv fdtcontroladdr 5ffc0e70
fw_setenv ipaddr 192.168.1.1
fw_setenv loadaddr 0x46000000
fw_setenv mtdids "spi-nand0=spi-nand0"
fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)"
fw_setenv netmask 255.255.255.0
fw_setenv serverip 192.168.1.2
fw_setenv stderr serial at 11002000
fw_setenv stdin serial at 11002000
fw_setenv stdout serial at 11002000
fw_setenv tp_boot_idx 0
14. Reboot to OpenWrt initramfs:
reboot
15. Login as root via SSH (IP 192.168.1.1, port 22)
16. Upload OpenWrt sysupgrade.bin image to the /tmp dir of the router
17. Run sysupgrade:
sysupgrade -n /tmp/sysupgrade.bin
Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware
Recovery (UART)
---------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
tftpboot initramfs-kernel.bin
bootm
4. Do what you need (restore partitions from a backup, install OpenWrt
etc.)
Stock layout
------------
0x000000000000-0x000000200000 : "boot"
0x000000200000-0x000000300000 : "u-boot-env"
0x000000300000-0x000003500000 : "ubi0"
0x000003500000-0x000006700000 : "ubi1"
0x000006700000-0x000006f00000 : "userconfig"
0x000006f00000-0x000007300000 : "tp_data"
ubi0/ubi1 format
----------------
U-Boot at boot checks that all volumes are in place:
+-------------------------------+
| Volume Name: uboot Vol ID: 0|
| Volume Name: kernel Vol ID: 1|
| Volume Name: rootfs Vol ID: 2|
+-------------------------------+
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| label | 00:eb:xx:xx:xx:be | label |
| LAN | 00:eb:xx:xx:xx:be | label |
| WAN | 00:eb:xx:xx:xx:bf | label+1 |
| WLAN 2g | 00:eb:xx:xx:xx:be | label |
| WLAN 5g | 00:eb:xx:xx:xx:bd | label-1 |
+---------+-------------------+-----------+
label MAC address was found in UBI partition "tp_data", file
"default-mac". OEM wireless eeprom is also there (file
"MT7986_EEPROM.bin").
Signed-off-by: Mikhail Zhilkin <csharper2005 at gmail.com>
---
package/boot/uboot-envtools/files/mediatek_filogic | 4 +
.../mediatek/dts/mt7986b-mercusys-mr90x-v1.dts | 276 +++++++++++++++++++++
.../filogic/base-files/etc/board.d/01_leds | 6 +
.../filogic/base-files/etc/board.d/02_network | 7 +
.../etc/hotplug.d/ieee80211/11_fix_wifi_mac | 5 +
.../base-files/lib/preinit/09_mount_cfg_part | 23 ++
.../base-files/lib/preinit/10_fix_eth_mac.sh | 6 +
.../filogic/base-files/lib/preinit/81_fix_eeprom | 16 ++
.../filogic/base-files/lib/upgrade/platform.sh | 4 +
target/linux/mediatek/image/filogic.mk | 14 ++
10 files changed, 361 insertions(+)
diff --git a/package/boot/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-envtools/files/mediatek_filogic
index 881d0c4501..7918bdacfc 100644
--- a/package/boot/uboot-envtools/files/mediatek_filogic
+++ b/package/boot/uboot-envtools/files/mediatek_filogic
@@ -40,6 +40,10 @@ bananapi,bpi-r3)
glinet,gl-mt3000)
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x80000" "0x20000"
;;
+mercusys,mr90x-v1)
+ local envdev=/dev/mtd$(find_mtd_index "u-boot-env")
+ ubootenv_add_uci_config "$envdev" "0x0" "0x20000" "0x20000" "1"
+ ;;
netgear,wax220)
ubootenv_add_uci_config "/dev/mtd5" "0x0" "0x20000" "0x20000"
;;
diff --git a/target/linux/mediatek/dts/mt7986b-mercusys-mr90x-v1.dts b/target/linux/mediatek/dts/mt7986b-mercusys-mr90x-v1.dts
new file mode 100644
index 0000000000..8b8858ccef
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7986b-mercusys-mr90x-v1.dts
@@ -0,0 +1,276 @@
+// SPDX-License-Identifier: (GL-2.0 OR MIT)
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+#include "mt7986b.dtsi"
+
+/ {
+ compatible = "mercusys,mr90x-v1", "mediatek,mt7986b";
+ model = "Mercusys MR90X v1";
+
+ aliases {
+ serial0 = &uart0;
+
+ led-boot = &led_status_green;
+ led-failsafe = &led_status_green;
+ led-running = &led_status_green;
+ led-upgrade = &led_status_green;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ reg = <0 0x40000000 0 0x20000000>;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ label = "green:lan2";
+ gpios = <&pio 7 GPIO_ACTIVE_LOW>;
+ };
+
+ led-1 {
+ label = "green:lan1";
+ gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+ };
+
+ led-2 {
+ label = "green:lan0";
+ gpios = <&pio 12 GPIO_ACTIVE_LOW>;
+ };
+
+ led-3 {
+ label = "green:wan";
+ gpios = <&pio 13 GPIO_ACTIVE_LOW>;
+ };
+
+ led-4 {
+ label = "orange:status";
+ gpios = <&pio 16 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_status_green: led-5 {
+ label = "green:status";
+ gpios = <&pio 17 GPIO_ACTIVE_HIGH>;
+ panic-indicator;
+ };
+ };
+};
+
+&crypto {
+ status = "okay";
+};
+
+ð {
+ status = "okay";
+
+ gmac0: mac at 0 {
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+
+ gmac1: mac at 1 {
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+ phy-handle = <&phy6>;
+ phy-mode = "2500base-x";
+ };
+
+ mdio: mdio-bus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
+
+&mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&pio 6 GPIO_ACTIVE_LOW>;
+ reset-delay-us = <1500000>;
+ reset-post-delay-us = <1000000>;
+
+ /* WAN/LAN 2.5Gbps phy
+ MaxLinear GPY211C0VC (SLNW8) */
+ phy6: phy at 6 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <6>;
+ };
+
+ switch: switch at 0 {
+ compatible = "mediatek,mt7531";
+ reg = <31>;
+ reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&switch {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* WAN/LAN 1Gbps port */
+ port at 0 {
+ reg = <0>;
+ label = "lan0";
+ };
+
+ /* LAN1 port */
+ port at 1 {
+ reg = <1>;
+ label = "lan1";
+ };
+
+ /* LAN2 port */
+ port at 2 {
+ reg = <2>;
+ label = "lan2";
+ };
+
+ port at 6 {
+ reg = <6>;
+ ethernet = <&gmac0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+};
+
+&pio {
+ spi_flash_pins: spi-flash-pins-33-to-38 {
+ mux {
+ function = "spi";
+ groups = "spi0", "spi0_wp_hold";
+ };
+ conf-pu {
+ pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
+ drive-strength = <8>;
+ mediatek,pull-up-adv = <0>; /* bias-disable */
+ };
+ conf-pd {
+ pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
+ drive-strength = <8>;
+ mediatek,pull-down-adv = <0>; /* bias-disable */
+ };
+ };
+
+ wf_2g_5g_pins: wf_2g_5g-pins {
+ mux {
+ function = "wifi";
+ groups = "wf_2g", "wf_5g";
+ };
+ conf {
+ pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+ "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+ "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+ "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+ "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+ "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+ "WF1_TOP_CLK", "WF1_TOP_DATA";
+ drive-strength = <4>;
+ };
+ };
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_flash_pins>;
+ status = "okay";
+
+ spi_nand_flash: flash at 0 {
+ compatible = "spi-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0>;
+
+ spi-max-frequency = <20000000>;
+ spi-tx-buswidth = <4>;
+ spi-rx-buswidth = <4>;
+
+ partitions: partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "boot";
+ reg = <0x0 0x200000>;
+ read-only;
+ };
+
+ partition at 200000 {
+ label = "u-boot-env";
+ reg = <0x200000 0x100000>;
+ };
+
+ partition at 300000 {
+ label = "ubi0";
+ reg = <0x300000 0x3200000>;
+ };
+
+ partition at 3500000 {
+ label = "ubi1";
+ reg = <0x3500000 0x3200000>;
+ read-only;
+ };
+
+ partition at 6700000 {
+ label = "userconfig";
+ reg = <0x6700000 0x800000>;
+ read-only;
+ };
+
+ partition at 6f00000 {
+ label = "tp_data";
+ reg = <0x6f00000 0x400000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&trng {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+&wifi {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wf_2g_5g_pins>;
+};
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
index 0ba825fd2b..c81bd2cd97 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
@@ -9,6 +9,12 @@ case $board in
cudy,wr3000-v1)
ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan"
;;
+mercusys,mr90x-v1)
+ ucidef_set_led_netdev "lan0" "lan0" "green:lan0" "lan0" "link tx rx"
+ ucidef_set_led_netdev "lan1" "lan2" "green:lan1" "lan1" "link tx rx"
+ ucidef_set_led_netdev "lan2" "lan2" "green:lan2" "lan2" "link tx rx"
+ ucidef_set_led_netdev "wan" "wan" "green:wan" "eth1" "link tx rx"
+ ;;
netgear,wax220)
ucidef_set_led_netdev "eth0" "LAN" "green:lan" "eth0"
ucidef_set_led_netdev "wlan2g" "WLAN2G" "blue:wlan2g" "phy0-ap0"
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
index 8803326b27..c05c5d25e4 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
@@ -32,6 +32,9 @@ mediatek_setup_interfaces()
mediatek,mt7988a-dsa-10g-spim-snand)
ucidef_set_interfaces_lan_wan "lan0 lan1 lan2 lan3" "eth1 eth2"
;;
+ mercusys,mr90x-v1)
+ ucidef_set_interfaces_lan_wan "lan0 lan1 lan2" eth1
+ ;;
qihoo,360t7)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" wan
;;
@@ -69,6 +72,10 @@ mediatek_setup_macs()
bananapi,bpi-r3)
wan_mac=$(macaddr_add $(cat /sys/class/net/eth0/address) 1)
;;
+ mercusys,mr90x-v1)
+ label_mac=$(get_mac_binary "/tmp/tp_data/default-mac" 0)
+ lan_mac=$label_mac
+ ;;
netgear,wax220)
lan_mac=$(mtd_get_mac_ascii u-boot-env mac)
label_mac=$lan_mac
diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
index 3969a7bfe4..4b7047eec5 100644
--- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
+++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
@@ -32,6 +32,11 @@ case "$board" in
[ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress
[ "$PHYNBR" = "1" ] && macaddr_setbit_la $(macaddr_add $addr 1) > /sys${DEVPATH}/macaddress
;;
+ mercusys,mr90x-v1)
+ addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0)
+ [ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress
+ [ "$PHYNBR" = "1" ] && macaddr_add $addr -1 > /sys${DEVPATH}/macaddress
+ ;;
netgear,wax220)
hw_mac_addr=$(mtd_get_mac_ascii u-boot-env mac)
[ "$PHYNBR" = "0" ] && macaddr_add $hw_mac_addr 2 > /sys${DEVPATH}/macaddress
diff --git a/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part b/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part
new file mode 100644
index 0000000000..819df40d08
--- /dev/null
+++ b/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part
@@ -0,0 +1,23 @@
+. /lib/functions/system.sh
+
+mount_ubi_part() {
+ local part_name="$1"
+ local mtd_num=$(grep $part_name /proc/mtd | cut -c4)
+ local ubi_num=$(ubiattach -m $mtd_num | \
+ awk -F',' '/UBI device number [0-9]{1,}/{print $1}' | \
+ awk '{print $4}')
+ mkdir /tmp/$part_name
+ mount -r -t ubifs ubi$ubi_num:$part_name /tmp/$part_name
+}
+
+preinit_mount_cfg_part() {
+ case $(board_name) in
+ mercusys,mr90x-v1)
+ mount_ubi_part "tp_data"
+ ;;
+ *)
+ ;;
+ esac
+}
+
+boot_hook_add preinit_main preinit_mount_cfg_part
diff --git a/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh b/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh
index ec078741c9..cfddd9cedc 100644
--- a/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh
+++ b/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh
@@ -8,6 +8,12 @@ preinit_set_mac_address() {
ip link set dev eth0 address "$addr"
ip link set dev eth1 address "$addr"
;;
+ mercusys,mr90x-v1)
+ addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0)
+ ip link set dev eth1 address "$(macaddr_add $addr 1)"
+ ;;
+ *)
+ ;;
esac
}
diff --git a/target/linux/mediatek/filogic/base-files/lib/preinit/81_fix_eeprom b/target/linux/mediatek/filogic/base-files/lib/preinit/81_fix_eeprom
new file mode 100644
index 0000000000..0a842facca
--- /dev/null
+++ b/target/linux/mediatek/filogic/base-files/lib/preinit/81_fix_eeprom
@@ -0,0 +1,16 @@
+. /lib/functions/system.sh
+
+preinit_fix_eeprom() {
+ case $(board_name) in
+ mercusys,mr90x-v1)
+ eeprom="/lib/firmware/mediatek/mt7986_eeprom_mt7975_dual.bin"
+ oem="/tmp/tp_data/MT7986_EEPROM.bin"
+ [ ! -L $eeprom -a -e $oem ] && \
+ mv -f $eeprom $eeprom.bak && ln -s $oem $eeprom
+ ;;
+ *)
+ ;;
+ esac
+}
+
+boot_hook_add preinit_main preinit_fix_eeprom
diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
index 5b624bc551..11c2c5c664 100755
--- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
+++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
@@ -70,6 +70,10 @@ platform_do_upgrade() {
cudy,wr3000-v1)
default_do_upgrade "$1"
;;
+ mercusys,mr90x-v1)
+ CI_UBIPART="ubi0"
+ nand_do_upgrade "$1"
+ ;;
qihoo,360t7|\
tplink,tl-xdr4288|\
tplink,tl-xdr6086|\
diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
index ae25aee2ed..fd83b9d441 100644
--- a/target/linux/mediatek/image/filogic.mk
+++ b/target/linux/mediatek/image/filogic.mk
@@ -250,6 +250,20 @@ define Device/mediatek_mt7988a-rfb-nand
endef
TARGET_DEVICES += mediatek_mt7988a-rfb-nand
+define Device/mercusys_mr90x-v1
+ DEVICE_VENDOR := Mercusys
+ DEVICE_MODEL := MR90X v1
+ DEVICE_DTS := mt7986b-mercusys-mr90x-v1
+ DEVICE_DTS_DIR := ../dts
+ DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware
+ UBINIZE_OPTS := -E 5
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ IMAGE_SIZE := 51200k
+ IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+endef
+TARGET_DEVICES += mercusys_mr90x-v1
+
define Device/qihoo_360t7
DEVICE_VENDOR := Qihoo
DEVICE_MODEL := 360T7
More information about the lede-commits
mailing list