[openwrt/openwrt] bmips: add support for Netgear DGND3700 v1, DGND3800B
LEDE Commits
lede-commits at lists.infradead.org
Sat Jun 10 06:43:23 PDT 2023
noltari pushed a commit to openwrt/openwrt.git, branch openwrt-23.05:
https://git.openwrt.org/f25afae0b51c47a185ae30d4414ce229f27feb8e
commit f25afae0b51c47a185ae30d4414ce229f27feb8e
Author: Daniel González Cabanelas <dgcbueu at gmail.com>
AuthorDate: Sat Jun 10 11:54:59 2023 +0200
bmips: add support for Netgear DGND3700 v1, DGND3800B
The Netgear DGND3700 v1 and DGND3800B are the same device but with
different factory firmwares. It's an xDSL wifi router with a slim black
shiny casing and 4 PCB internal antennas connected via UFL to a miniPCI
detachable card.
Hardware:
- SoC: Broadcom BCM6368
- CPU: dual core BMIPS4350 V3.1 @400Mhz
- RAM: 128 MB DDR
- NOR Flash: 32 MB parallel (CFE and OS)
- NAND flash: 128 MB (empty)
- Ethernet LAN: 5x 1Gbit
- Wifi 2.4 GHz: Broadcom BCM43222 802.11bgn
- Wifi 5 GHz: Broadcom BCM43222 802.11abgn
- USB: 2x 2.0
- Buttons: 3x, 1 reset
- LEDs: 11x
- UART: yes
Installation via OEM web UI:
1. Open the Netgear administration web interface, by default:
http://192.168.0.1
user: admin
password: password
2. Look for "upgrade firmware" and proceed
3. Wait some minutes until it finishes
Signed-off-by: Daniel González Cabanelas <dgcbueu at gmail.com>
---
.../bmips/bcm6368/base-files/etc/board.d/01_leds | 9 +
.../bcm6368/base-files/etc/board.d/02_network | 5 +
.../bmips/dts/bcm6368-netgear-dgnd3700-v1.dts | 8 +
.../linux/bmips/dts/bcm6368-netgear-dgnd3700.dtsi | 266 +++++++++++++++++++++
.../linux/bmips/dts/bcm6368-netgear-dgnd3800b.dts | 8 +
target/linux/bmips/image/Makefile | 9 +
target/linux/bmips/image/bcm6368.mk | 29 +++
7 files changed, 334 insertions(+)
diff --git a/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds b/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds
index ab797568b7..e68a4e947b 100644
--- a/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds
+++ b/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds
@@ -6,6 +6,15 @@
board_config_update
case "$(board_name)" in
+netgear,dgnd3700-v1 |\
+netgear,dgnd3800b)
+ ucidef_set_led_netdev "lan" "LAN" "green:lan" "switch.1"
+ ucidef_set_led_netdev "wan" "WAN" "green:wan" "wan"
+ ucidef_set_led_netdev "wlan0" "WIFI2G" "green:wifi2g" "phy0-ap0"
+ ucidef_set_led_netdev "wlan1" "WIFI5G" "blue:wifi5g" "phy1-ap0"
+ ucidef_set_led_usbport "usb1" "USB1" "green:usb1" "usb1-port1" "usb2-port1"
+ ucidef_set_led_usbport "usb2" "USB2" "green:usb2" "usb1-port2" "usb2-port2"
+ ;;
observa,vh4032n)
ucidef_set_led_usbport "usb1" "USB1" "blue:hspa" "usb1-port1" "usb2-port1"
ucidef_set_led_usbport "usb2" "USB2" "red:hspa" "1-2-port1" "1-2-port2"
diff --git a/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network b/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network
index 1064b80fba..f99005acd7 100644
--- a/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network
+++ b/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network
@@ -10,6 +10,11 @@ observa,vh4032n)
ucidef_set_bridge_device switch
ucidef_set_interface_lan "lan1 lan2 lan3 lan4"
;;
+netgear,dgnd3700-v1 |\
+netgear,dgnd3800b)
+ ucidef_set_bridge_device switch
+ ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
+ ;;
esac
board_config_flush
diff --git a/target/linux/bmips/dts/bcm6368-netgear-dgnd3700-v1.dts b/target/linux/bmips/dts/bcm6368-netgear-dgnd3700-v1.dts
new file mode 100644
index 0000000000..4ec6c48083
--- /dev/null
+++ b/target/linux/bmips/dts/bcm6368-netgear-dgnd3700-v1.dts
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "bcm6368-netgear-dgnd3700.dtsi"
+
+/ {
+ model = "Netgear DGND3700 v1";
+ compatible = "netgear,dgnd3700-v1", "brcm,bcm6368";
+};
diff --git a/target/linux/bmips/dts/bcm6368-netgear-dgnd3700.dtsi b/target/linux/bmips/dts/bcm6368-netgear-dgnd3700.dtsi
new file mode 100644
index 0000000000..2299611d55
--- /dev/null
+++ b/target/linux/bmips/dts/bcm6368-netgear-dgnd3700.dtsi
@@ -0,0 +1,266 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "bcm6368.dtsi"
+
+/ {
+ aliases {
+ led-boot = &led_power_green;
+ led-failsafe = &led_power_red;
+ led-running = &led_power_green;
+ led-upgrade = &led_power_green;
+ };
+
+ keys {
+ compatible = "gpio-keys-polled";
+ poll-interval = <100>;
+
+ rfkill {
+ label = "rfkill";
+ gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ debounce-interval = <60>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ debounce-interval = <60>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&gpio 35 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ debounce-interval = <60>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led at 2 {
+ label = "green:dsl";
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ };
+
+ led at 4 {
+ label = "red:wan";
+ gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+ };
+
+ led at 5 {
+ label = "green:wan";
+ gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+ };
+
+ led at 11 {
+ label = "green:wps";
+ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ };
+
+ /* usb front */
+ led at 13 {
+ label = "green:usb2";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ };
+
+ /* usb back */
+ led at 14 {
+ label = "green:usb1";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ };
+
+ led_power_red: led at 22 {
+ label = "red:power";
+ gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
+ panic-indicator;
+ };
+
+ led at 23 {
+ label = "green:lan";
+ gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
+ };
+
+ led_power_green: led at 24 {
+ label = "green:power";
+ gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ led at 26 {
+ label = "green:wifi2g";
+ gpios = <&gpio 26 GPIO_ACTIVE_LOW>;
+ };
+
+ led at 27 {
+ label = "blue:wifi5g";
+ gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&ehci {
+ status = "okay";
+};
+
+ðernet {
+ status = "okay";
+
+ nvmem-cells = <&macaddr_cfe_6a0>;
+ nvmem-cell-names = "mac-address";
+};
+
+&lsspi {
+ status = "okay";
+
+ switch at 1 {
+ compatible = "brcm,bcm53115";
+ reg = <1>;
+ spi-max-frequency = <781000>;
+ dsa,member = <1 0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ wan at 0 {
+ reg = <0>;
+ label = "wan";
+ };
+
+ port at 1 {
+ reg = <1>;
+ label = "lan4";
+ };
+
+ port at 2 {
+ reg = <2>;
+ label = "lan3";
+ };
+
+ port at 3 {
+ reg = <3>;
+ label = "lan2";
+ };
+
+ port at 4 {
+ reg = <4>;
+ label = "lan1";
+ };
+
+ port at 8 {
+ reg = <8>;
+
+ phy-mode = "rgmii";
+ ethernet = <&switch0port5>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+};
+
+&nflash {
+ status = "okay";
+
+ nandcs at 0 {
+ compatible = "brcm,nandcs";
+ reg = <0>;
+ nand-ecc-step-size = <512>;
+ nand-ecc-strength = <15>;
+ nand-on-flash-bbt;
+ brcm,nand-oob-sector-size = <64>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "storage";
+ reg = <0 0>; /* autodetected size */
+ };
+ };
+ };
+};
+
+&ohci {
+ status = "okay";
+};
+
+&pci {
+ status = "okay";
+};
+
+&pflash {
+ status = "okay";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cfe: partition at 0 {
+ label = "CFE";
+ reg = <0x0000000 0x0020000>;
+ read-only;
+ };
+
+ partition at 20000 {
+ compatible = "brcm,bcm963xx-imagetag";
+ label = "firmware";
+ reg = <0x0020000 0x1e20000>;
+ };
+
+ partition at 1e40000 {
+ label = "board_data";
+ reg = <0x1e40000 0x1a0000>;
+ read-only;
+ };
+
+ partition at 1fe0000 {
+ label = "nvram";
+ reg = <0x1fe0000 0x020000>;
+ };
+ };
+};
+
+&switch0 {
+ dsa,member = <0 0>;
+
+ ports {
+ switch0port5: port at 5 {
+ reg = <5>;
+ label = "extsw";
+
+ phy-mode = "rgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&usbh {
+ status = "okay";
+};
+
+&cfe {
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_cfe_6a0: macaddr at 6a0 {
+ reg = <0x6a0 0x6>;
+ };
+};
diff --git a/target/linux/bmips/dts/bcm6368-netgear-dgnd3800b.dts b/target/linux/bmips/dts/bcm6368-netgear-dgnd3800b.dts
new file mode 100644
index 0000000000..350d3619c0
--- /dev/null
+++ b/target/linux/bmips/dts/bcm6368-netgear-dgnd3800b.dts
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "bcm6368-netgear-dgnd3700.dtsi"
+
+/ {
+ model = "Netgear DGND3800B";
+ compatible = "netgear,dgnd3800b", "brcm,bcm6368";
+};
diff --git a/target/linux/bmips/image/Makefile b/target/linux/bmips/image/Makefile
index b5e3098fe7..58685dec74 100644
--- a/target/linux/bmips/image/Makefile
+++ b/target/linux/bmips/image/Makefile
@@ -313,6 +313,15 @@ define Device/bcm63xx-nand
DEVICE_PACKAGES += nand-utils
endef
+define Device/bcm63xx_netgear
+ $(Device/bcm63xx-cfe)
+ DEVICE_VENDOR := NETGEAR
+ IMAGES := factory.chk sysupgrade.bin
+ IMAGE/factory.chk := cfe-bin | netgear-chk
+ NETGEAR_BOARD_ID :=
+ NETGEAR_REGION :=
+endef
+
define Device/sercomm-nand
$(Device/bcm63xx-nand)
IMAGES := factory.img sysupgrade.bin
diff --git a/target/linux/bmips/image/bcm6368.mk b/target/linux/bmips/image/bcm6368.mk
index e3aa40d404..41bce9e938 100644
--- a/target/linux/bmips/image/bcm6368.mk
+++ b/target/linux/bmips/image/bcm6368.mk
@@ -14,6 +14,35 @@ define Device/comtrend_vr-3025u
endef
TARGET_DEVICES += comtrend_vr-3025u
+define Device/netgear_dgnd3700-v1
+ $(Device/bcm63xx_netgear)
+ DEVICE_VENDOR := NETGEAR
+ DEVICE_MODEL := DGND3700
+ DEVICE_VARIANT := v1
+ CFE_BOARD_ID := 96368MVWG
+ CHIP_ID := 6368
+ BLOCKSIZE := 0x20000
+ NETGEAR_BOARD_ID := U12L144T01_NETGEAR_NEWLED
+ NETGEAR_REGION := 1
+ DEVICE_PACKAGES += $(USB2_PACKAGES) \
+ $(B43_PACKAGES)
+endef
+TARGET_DEVICES += netgear_dgnd3700-v1
+
+define Device/netgear_dgnd3800b
+ $(Device/bcm63xx_netgear)
+ DEVICE_VENDOR := NETGEAR
+ DEVICE_MODEL := DGND3800B
+ CFE_BOARD_ID := 96368MVWG
+ CHIP_ID := 6368
+ BLOCKSIZE := 0x20000
+ NETGEAR_BOARD_ID := U12L144T11_NETGEAR_NEWLED
+ NETGEAR_REGION := 1
+ DEVICE_PACKAGES += $(USB2_PACKAGES) \
+ $(B43_PACKAGES)
+endef
+TARGET_DEVICES += netgear_dgnd3800b
+
define Device/observa_vh4032n
$(Device/bcm63xx-cfe)
DEVICE_VENDOR := Observa
More information about the lede-commits
mailing list