[openwrt/openwrt] bmips: add support for Observa VH4032N
LEDE Commits
lede-commits at lists.infradead.org
Sat Jun 10 06:43:22 PDT 2023
noltari pushed a commit to openwrt/openwrt.git, branch openwrt-23.05:
https://git.openwrt.org/725319ad3857e0d6b2f5f900e9ab2f779ad53410
commit 725319ad3857e0d6b2f5f900e9ab2f779ad53410
Author: Daniel González Cabanelas <dgcbueu at gmail.com>
AuthorDate: Fri Jun 9 00:09:33 2023 +0200
bmips: add support for Observa VH4032N
The Observa VH4032N is an xDSL wifi router with a vertical white casing
and two internal antennas connected via UFL.
Hardware:
- SoC: Broadcom BCM6368
- CPU: dual core BMIPS4350 V3.1 @400MHz
- RAM: 128 MB DDR
- Flash: 32 MB parallel NOR
- Ethernet LAN: 4x 100Mbit
- Wifi 2.4/5 GHz: onboard Broadcom BCM43222 802.11abgn
- USB: 3x 2.0
- Buttons: 2x, 1 reset
- LEDs: 8x, blue and red
- UART: 1x
Installation via OEM web UI:
1. Use the admin credentials to login via web UI
2. Go to Managament->Update firmware and select the OpenWrt CFE firmware
3. Press "Update Firmware" button and wait some minutes until it finish
Signed-off-by: Daniel González Cabanelas <dgcbueu at gmail.com>
---
.../bmips/bcm6368/base-files/etc/board.d/01_leds | 17 ++
.../bcm6368/base-files/etc/board.d/02_network | 3 +-
.../bcm6368/base-files/etc/uci-defaults/09_fix_crc | 3 +-
target/linux/bmips/dts/bcm6368-observa-vh4032n.dts | 233 +++++++++++++++++++++
target/linux/bmips/image/bcm6368.mk | 15 ++
5 files changed, 269 insertions(+), 2 deletions(-)
diff --git a/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds b/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds
new file mode 100644
index 0000000000..ab797568b7
--- /dev/null
+++ b/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds
@@ -0,0 +1,17 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+
+. /lib/functions/leds.sh
+. /lib/functions/uci-defaults.sh
+
+board_config_update
+
+case "$(board_name)" in
+observa,vh4032n)
+ ucidef_set_led_usbport "usb1" "USB1" "blue:hspa" "usb1-port1" "usb2-port1"
+ ucidef_set_led_usbport "usb2" "USB2" "red:hspa" "1-2-port1" "1-2-port2"
+ ;;
+esac
+
+board_config_flush
+
+exit 0
diff --git a/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network b/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network
index 14d6e56dd1..1064b80fba 100644
--- a/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network
+++ b/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network
@@ -5,7 +5,8 @@
board_config_update
case "$(board_name)" in
-comtrend,vr-3025u)
+comtrend,vr-3025u |\
+observa,vh4032n)
ucidef_set_bridge_device switch
ucidef_set_interface_lan "lan1 lan2 lan3 lan4"
;;
diff --git a/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc b/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc
index c66e4169fd..d4ff723d14 100644
--- a/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc
+++ b/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc
@@ -3,7 +3,8 @@
. /lib/functions.sh
case "$(board_name)" in
-comtrend,vr-3025u)
+comtrend,vr-3025u |\
+observa,vh4032n)
mtd fixtrx firmware
;;
esac
diff --git a/target/linux/bmips/dts/bcm6368-observa-vh4032n.dts b/target/linux/bmips/dts/bcm6368-observa-vh4032n.dts
new file mode 100644
index 0000000000..4a4cca0982
--- /dev/null
+++ b/target/linux/bmips/dts/bcm6368-observa-vh4032n.dts
@@ -0,0 +1,233 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "bcm6368.dtsi"
+
+/ {
+ model = "Observa VH4032N";
+ compatible = "observa,vh4032n", "brcm,bcm6368";
+
+ aliases {
+ led-boot = &led_power_blue;
+ led-failsafe = &led_power_red;
+ led-running = &led_power_blue;
+ led-upgrade = &led_power_blue;
+ };
+
+ keys {
+ compatible = "gpio-keys-polled";
+ poll-interval = <100>;
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 34 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ debounce-interval = <60>;
+ };
+
+ rfkill {
+ label = "rfkill";
+ gpios = <&gpio 35 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ debounce-interval = <60>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led at 2 {
+ label = "blue:dsl";
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ };
+
+ led at 5 {
+ label = "red:dsl";
+ gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+ };
+
+ led at 11 {
+ label = "blue:hspa";
+ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ };
+
+ led at 12 {
+ label = "red:hspa";
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ };
+
+ led_power_blue: led at 22 {
+ label = "blue:power";
+ gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ led_power_red: led at 24 {
+ label = "red:power";
+ gpios = <&gpio 24 GPIO_ACTIVE_HIGH>;
+ };
+
+ led at 25 {
+ label = "blue:voice";
+ gpios = <&gpio 25 GPIO_ACTIVE_LOW>;
+ };
+
+ led at 26 {
+ label = "red:voice";
+ gpios = <&gpio 26 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ bcm43222-sprom {
+ compatible = "brcm,ssb-sprom";
+
+ pci-bus = <0>;
+ pci-dev = <1>;
+
+ nvmem-cells = <&macaddr_cfe_6a0>;
+ nvmem-cell-names = "mac-address";
+ mac-address-increment = <1>;
+
+ brcm,sprom = "brcm/bcm43222-sprom.bin";
+ brcm,sprom-fixups = <2 0x04d2>, <4 0x4350>,
+ <65 0x1300>, <68 0x0402>,
+ <70 0x0090>, <71 0x4c19>,
+ <72 0x2345>, <87 0x0315>,
+ <88 0x0315>, <96 0x2048>,
+ <97 0xfed7>, <98 0x15a6>,
+ <99 0xfaee>, <100 0x3e3a>,
+ <101 0x3a36>, <102 0xff7f>,
+ <103 0x11b9>, <104 0xfc53>,
+ <105 0xffe6>, <106 0xfdd2>,
+ <107 0xfe49>, <108 0xff6a>,
+ <109 0x136e>, <110 0xfbed>,
+ <111 0x0000>, <112 0x2048>,
+ <113 0xfee2>, <114 0x15e5>,
+ <115 0xfaed>, <116 0x3e3a>,
+ <117 0x3a36>, <118 0xffc8>,
+ <119 0x12b8>, <120 0xfca1>,
+ <121 0xff9b>, <122 0x122a>,
+ <123 0xfcc8>, <124 0xff95>,
+ <125 0x146b>, <126 0xfbba>,
+ <127 0x0000>, <161 0x0000>,
+ <162 0x0000>, <169 0x0000>,
+ <170 0x0000>, <171 0x0000>,
+ <172 0x0000>, <173 0x0000>,
+ <174 0x0000>, <175 0x0000>,
+ <176 0x0000>, <219 0x1108>;
+ };
+};
+
+&ehci {
+ status = "okay";
+};
+
+ðernet {
+ status = "okay";
+
+ nvmem-cells = <&macaddr_cfe_6a0>;
+ nvmem-cell-names = "mac-address";
+};
+
+&gpio {
+ usb_hub_reset {
+ gpio-hog;
+ gpios = <27 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "usb-hub-reset-gpio";
+ };
+};
+
+&ohci {
+ status = "okay";
+};
+
+&pci {
+ status = "okay";
+};
+
+&pflash {
+ status = "okay";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cfe: partition at 0 {
+ label = "CFE";
+ reg = <0x0000000 0x0020000>;
+ read-only;
+ };
+
+ partition at 20000 {
+ compatible = "brcm,bcm963xx-imagetag";
+ label = "firmware";
+ reg = <0x0020000 0x1fc0000>;
+ };
+
+ partition at 1fe0000 {
+ label = "nvram";
+ reg = <0x1fe0000 0x020000>;
+ };
+ };
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ephy0_led &pinctrl_ephy1_led
+ &pinctrl_ephy2_led &pinctrl_ephy3_led>;
+};
+
+&switch0 {
+ ports {
+ port at 0 {
+ reg = <0>;
+ label = "lan4";
+
+ phy-handle = <&phy1>;
+ phy-mode = "mii";
+ };
+
+ port at 1 {
+ reg = <1>;
+ label = "lan3";
+
+ phy-handle = <&phy2>;
+ phy-mode = "mii";
+ };
+
+ port at 2 {
+ reg = <2>;
+ label = "lan2";
+
+ phy-handle = <&phy3>;
+ phy-mode = "mii";
+ };
+
+ port at 3 {
+ reg = <3>;
+ label = "lan1";
+
+ phy-handle = <&phy4>;
+ phy-mode = "mii";
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&usbh {
+ status = "okay";
+};
+
+&cfe {
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_cfe_6a0: macaddr at 6a0 {
+ reg = <0x6a0 0x6>;
+ };
+};
diff --git a/target/linux/bmips/image/bcm6368.mk b/target/linux/bmips/image/bcm6368.mk
index 268b68dd7c..e3aa40d404 100644
--- a/target/linux/bmips/image/bcm6368.mk
+++ b/target/linux/bmips/image/bcm6368.mk
@@ -13,3 +13,18 @@ define Device/comtrend_vr-3025u
kmod-leds-gpio
endef
TARGET_DEVICES += comtrend_vr-3025u
+
+define Device/observa_vh4032n
+ $(Device/bcm63xx-cfe)
+ DEVICE_VENDOR := Observa
+ DEVICE_MODEL := VH4032N
+ IMAGES += sysupgrade.bin
+ CFE_BOARD_ID := 96368VVW
+ CHIP_ID := 6368
+ BLOCKSIZE := 0x20000
+ FLASH_MB := 32
+ DEVICE_PACKAGES += $(USB2_PACKAGES) \
+ $(B43_PACKAGES) broadcom-43222-sprom \
+ kmod-leds-gpio
+endef
+TARGET_DEVICES += observa_vh4032n
More information about the lede-commits
mailing list