[openwrt/openwrt] hostapd: add default_disabled option to the supplicant

[LEDE Commits]

aparcar pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/acdb7c38c6f4411f5d2e96b45fff942505de58d1

commit acdb7c38c6f4411f5d2e96b45fff942505de58d1
Author: Raphaël Mélotte <raphael.melotte at mind.be>
AuthorDate: Wed Oct 7 10:08:14 2020 +0200

    hostapd: add default_disabled option to the supplicant
    
    With the default configuration we generate, the supplicant starts
    scanning and tries to connect to any open network when the interface
    is enabled.
    
    In some cases it can be desirable to prevent the supplicant from
    scanning by itself. For example, if on the same radio an AP is
    configured and an unconfigured STA is added (to be configured with
    WPS), the AP might not be able to beacon until the STA stops
    scanning.
    
    In such a case, the STA configuration can still be required to set
    specific settings (e.g. multi_ap_backhaul_sta) so it can't be set to
    "disabled" in uci (because that would prevent the supplicant from
    being run at all). The alternative is to add the "disabled" parameter
    to the default network block in the supplicant configuration.
    
    This patch adds a "default_disabled" setting in UCI which, when set,
    adds the "disabled" parameter to the supplicant default network block.
    
    Signed-off-by: Raphaël Mélotte <raphael.melotte at mind.be>
---
 package/network/services/hostapd/files/hostapd.sh | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)

diff --git a/package/network/services/hostapd/files/hostapd.sh b/package/network/services/hostapd/files/hostapd.sh
index 4a5f8d61fe..a32e1652ac 100644
--- a/package/network/services/hostapd/files/hostapd.sh
+++ b/package/network/services/hostapd/files/hostapd.sh
@@ -350,6 +350,7 @@ hostapd_common_add_bss_config() {
 	config_add_boolean multicast_to_unicast proxy_arp per_sta_vif
 
 	config_add_array hostapd_bss_options
+	config_add_boolean default_disabled
 
 	config_add_boolean request_cui
 	config_add_array radius_auth_req_attr
@@ -1188,7 +1189,8 @@ wpa_supplicant_add_network() {
 		ssid bssid key \
 		basic_rate mcast_rate \
 		ieee80211w ieee80211r \
-		multi_ap
+		multi_ap \
+		default_disabled
 
 	case "$auth_type" in
 		sae|owe|eap192|eap-eap192)
@@ -1201,6 +1203,7 @@ wpa_supplicant_add_network() {
 
 	set_default ieee80211r 0
 	set_default multi_ap 0
+	set_default default_disabled 0
 
 	local key_mgmt='NONE'
 	local network_data=
@@ -1232,7 +1235,10 @@ wpa_supplicant_add_network() {
 		scan_ssid=""
 	}
 
-	[ "$multi_ap" = 1 -a "$_w_mode" = "sta" ] && append network_data "multi_ap_backhaul_sta=1" "$N$T"
+	[ "$_w_mode" = "sta" ] && {
+		[ "$multi_ap" = 1 ] && append network_data "multi_ap_backhaul_sta=1" "$N$T"
+		[ "$default_disabled" = 1 ] && append network_data "disabled=1" "$N$T"
+	}
 
 	case "$auth_type" in
 		none) ;;