[openwrt/openwrt] ath79: add support for MikroTik RouterBOARD 912UAG-2HPnD
LEDE Commits
lede-commits at lists.infradead.org
Mon Jun 21 01:51:26 PDT 2021
xback pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/695a1cd53ca52c678b3f837deb1bf30204285360
commit 695a1cd53ca52c678b3f837deb1bf30204285360
Author: Denis Kalashnikov <denis281089 at gmail.com>
AuthorDate: Thu May 27 11:16:46 2021 +0300
ath79: add support for MikroTik RouterBOARD 912UAG-2HPnD
This board has been supported in the ar71xx.
Links:
* https://mikrotik.com/product/RB912UAG-2HPnD
* https://openwrt.org/toh/hwdata/mikrotik/mikrotik_rb912uag-2hpnd
This also supports the 5GHz flavour of the board.
Hardware:
* SoC: Atheros AR9342,
* RAM: DDR 64MB,
* SPI NOR: 64KB,
* NAND: 128MB,
* Ethernet: x1 10/100/1000 port with passive POE in,
* Wi-Fi: 802.11 b/g/n,
* PCIe,
* USB: 2.0 EHCI controller, connected to mPCIe slot and a Type-A
port -- both can be used for LTE modem, but only one can be
used at any time.
* LEDs: 5 general purpose LEDs (led1..led5), power LED, user LED,
Ethernet phy LED,
* Button,
* Beeper.
Not working:
* Button: it shares gpio line 15 with NAND ALE and NAND IO7,
and current drivers doesn't easily support this configuration,
* Beeper: it is connected to bit 5 of a serial shift register
(tested with sysfs led trigger timer). But kmod-gpio-beeper
doesn't work -- we left this as is for now.
Flashing:
* Use the RouterBOARD Reset button to enable TFTP netboot,
boot kernel and initramfs and then perform sysupgrade.
* From ar71xx OpenWrt firmware run:
$ sysupgrade -F /tmp/<sysupgrade.bin>
For more info see: https://openwrt.org/toh/mikrotik/common.
Co-Developed-by: Koen Vandeputte <koen.vandeputte at citymesh.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a at gmail.com>
Signed-off-by: Denis Kalashnikov <denis281089 at gmail.com>
---
.../ar9342_mikrotik_routerboard-912uag-2hpnd.dts | 212 +++++++++++++++++++++
target/linux/ath79/image/mikrotik.mk | 9 +
.../mikrotik/base-files/etc/board.d/02_network | 2 +
.../etc/hotplug.d/firmware/10-ath9k-eeprom | 1 +
.../mikrotik/base-files/lib/upgrade/platform.sh | 1 +
5 files changed, 225 insertions(+)
diff --git a/target/linux/ath79/dts/ar9342_mikrotik_routerboard-912uag-2hpnd.dts b/target/linux/ath79/dts/ar9342_mikrotik_routerboard-912uag-2hpnd.dts
new file mode 100644
index 0000000000..cc5553acda
--- /dev/null
+++ b/target/linux/ath79/dts/ar9342_mikrotik_routerboard-912uag-2hpnd.dts
@@ -0,0 +1,212 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "ar9344.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "mikrotik,routerboard-912uag-2hpnd", "qca,ar9342";
+ model = "MikroTik RouterBOARD 912UAG-2HPnD";
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ gpio_latch: gpio_latch {
+ compatible = "gpio-latch";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpios = <&gpio 0 GPIO_ACTIVE_HIGH>,
+ <&gpio 1 GPIO_ACTIVE_HIGH>,
+ <&gpio 2 GPIO_ACTIVE_HIGH>,
+ <&gpio 3 GPIO_ACTIVE_HIGH>,
+ <0>, /* Not connected */
+ <&gpio 13 GPIO_ACTIVE_HIGH>,
+ <&gpio 14 GPIO_ACTIVE_HIGH>,
+ <&gpio 15 GPIO_ACTIVE_HIGH>,
+ <&gpio 11 GPIO_ACTIVE_LOW>; /* Latch Enable */
+ };
+
+ nand_gpio {
+ compatible = "mikrotik,rb91x-nand";
+
+ gpios = <&gpio_latch 3 GPIO_ACTIVE_HIGH>, /* Read */
+ <&gpio 4 GPIO_ACTIVE_HIGH>, /* Ready (RDY) */
+ <&gpio_latch 5 GPIO_ACTIVE_LOW>, /* Chip Enable (nCE) */
+ <&gpio_latch 6 GPIO_ACTIVE_HIGH>, /* Command Latch Enable (CLE) */
+ <&gpio_latch 7 GPIO_ACTIVE_HIGH>, /* Address Latch Enable (ALE) */
+ <&gpio 12 GPIO_ACTIVE_LOW>, /* Read/Write Enable (nRW) */
+ <&gpio_latch 8 GPIO_ACTIVE_LOW>; /* Latch Enable (nLE) */
+
+ partitions {
+ compatible = "fixed-partitions";
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "booter";
+ reg = <0x0 0x0040000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "kernel";
+ reg = <0x0040000 0x03c0000>;
+ };
+
+ partition at 400000 {
+ label = "ubi";
+ reg = <0x0400000 0x7c00000>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "green:power";
+ gpios = <&gpio_latch 1 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ user {
+ label = "green:user";
+ gpios = <&gpio_latch 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ led1 {
+ label = "green:led1";
+ gpios = <&ssr 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ led2 {
+ label = "green:led2";
+ gpios = <&ssr 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ led3 {
+ label = "green:led3";
+ gpios = <&ssr 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ led4 {
+ label = "green:led4";
+ gpios = <&ssr 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ led5 {
+ label = "green:led5";
+ gpios = <&ssr 4 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio-export {
+ compatible = "gpio-export";
+
+ usb_power {
+ gpio-export,name = "power-usb";
+ gpio-export,output = <1>;
+ gpios = <&ssr 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ pcie_power {
+ gpio-export,name = "power-pcie";
+ gpio-export,output = <0>;
+ gpios = <&ssr 7 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&spi {
+ status = "okay";
+
+ compatible = "qca,ar7100-spi";
+
+ cs-gpios = <0>, <&gpio_latch 0 GPIO_ACTIVE_LOW>;
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+
+ partitions {
+ compatible = "mikrotik,routerboot-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "routerboot";
+ reg = <0x0 0x0>;
+ read-only;
+ };
+
+ hard_config: hard_config {
+ read-only;
+ };
+
+ bios {
+ size = <0x1000>;
+ read-only;
+ };
+
+ soft_config {
+ };
+ };
+ };
+
+ ssr: ssr at 1 {
+ compatible = "fairchild,74hc595";
+ gpio-controller;
+ #gpio-cells = <2>;
+ registers-number = <1>;
+ reg = <1>;
+ spi-max-frequency = <50000000>;
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy-mask = <0>;
+
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ phy-mode = "rgmii-id";
+ phy-handle = <&phy0>;
+ pll-data = <0x02000000 0x00000101 0x00001313>;
+
+ gmac-config {
+ device = <&gmac>;
+ rgmii-gmac0 = <1>;
+ rgmii-enabled = <1>;
+ rxd-delay = <1>;
+ txd-delay = <1>;
+ };
+};
+
+&wmac {
+ status = "okay";
+ qca,no-eeprom;
+};
+
+&pcie {
+ status = "okay";
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb_phy {
+ status = "okay";
+};
diff --git a/target/linux/ath79/image/mikrotik.mk b/target/linux/ath79/image/mikrotik.mk
index 74f8603b5a..96a94793a9 100644
--- a/target/linux/ath79/image/mikrotik.mk
+++ b/target/linux/ath79/image/mikrotik.mk
@@ -9,6 +9,15 @@ define Device/mikrotik_routerboard-493g
endef
TARGET_DEVICES += mikrotik_routerboard-493g
+define Device/mikrotik_routerboard-912uag-2hpnd
+ $(Device/mikrotik_nand)
+ SOC := ar9342
+ DEVICE_MODEL := RouterBOARD 912UAG-2HPnD
+ DEVICE_PACKAGES += kmod-usb-ehci kmod-usb2 kmod-gpio-beeper
+ SUPPORTED_DEVICES += rb-912uag-2hpnd
+endef
+TARGET_DEVICES += mikrotik_routerboard-912uag-2hpnd
+
define Device/mikrotik_routerboard-921gs-5hpacd-15s
$(Device/mikrotik_nand)
SOC := qca9558
diff --git a/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network b/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network
index 4ffe82588c..d4a32c1e1a 100644
--- a/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network
@@ -14,6 +14,7 @@ ath79_setup_interfaces()
ucidef_add_switch "switch1" \
"0 at eth1" "1:lan:4" "2:lan:1" "3:lan:2" "4:lan:3"
;;
+ mikrotik,routerboard-912uag-2hpnd|\
mikrotik,routerboard-921gs-5hpacd-15s|\
mikrotik,routerboard-lhg-2nd|\
mikrotik,routerboard-sxt-5nd-r2|\
@@ -36,6 +37,7 @@ ath79_setup_macs()
local mac_base="$(cat /sys/firmware/mikrotik/hard_config/mac_base)"
case "$board" in
+ mikrotik,routerboard-912uag-2hpnd|\
mikrotik,routerboard-921gs-5hpacd-15s|\
mikrotik,routerboard-lhg-2nd|\
mikrotik,routerboard-sxt-5nd-r2|\
diff --git a/target/linux/ath79/mikrotik/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/mikrotik/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index d9425d4437..78aa35dc69 100644
--- a/target/linux/ath79/mikrotik/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/mikrotik/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -23,6 +23,7 @@ board=$(board_name)
case "$FIRMWARE" in
"ath9k-eeprom-ahb-18100000.wmac.bin")
case $board in
+ mikrotik,routerboard-912uag-2hpnd|\
mikrotik,routerboard-lhg-2nd|\
mikrotik,routerboard-sxt-5nd-r2|\
mikrotik,routerboard-wapr-2nd)
diff --git a/target/linux/ath79/mikrotik/base-files/lib/upgrade/platform.sh b/target/linux/ath79/mikrotik/base-files/lib/upgrade/platform.sh
index 97d388168f..6962c6fdcc 100644
--- a/target/linux/ath79/mikrotik/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ath79/mikrotik/base-files/lib/upgrade/platform.sh
@@ -32,6 +32,7 @@ platform_do_upgrade() {
case "$board" in
mikrotik,routerboard-493g|\
+ mikrotik,routerboard-912uag-2hpnd|\
mikrotik,routerboard-921gs-5hpacd-15s|\
mikrotik,routerboard-922uags-5hpacd|\
mikrotik,routerboard-sxt-5nd-r2)
More information about the lede-commits
mailing list