[openwrt/openwrt] ath79: add support for WD My Net N600
LEDE Commits
lede-commits at lists.infradead.org
Fri Dec 10 15:51:44 PST 2021
chunkeey pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/35aecc9d4a735c36d5eefe6e821c5930f736635f
commit 35aecc9d4a735c36d5eefe6e821c5930f736635f
Author: Ryan Mounce <ryan at mounce.com.au>
AuthorDate: Tue Nov 16 21:55:19 2021 +1030
ath79: add support for WD My Net N600
SoC: AR9344
RAM: 128MB
Flash: 16MiB SPI NOR
5GHz WiFi: AR9382 PCIe 2x2:2 802.11n
2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n
5x Fast ethernet via SoC switch (green LEDs)
1x USB 2.0
4x front LEDs from SoC GPIO
1x front WPS button from SoC GPIO
1x bottom reset button from SoC GPIO
UART header JP1, 115200 no parity 1 stop
TX
GND
VCC
(N/P)
RX
Flash factory image via "emergency room" recovery:
- Configure your computer with a static IP 192.168.1.123/24
- Connect to LAN port on the N600 switch
- Hold reset putton
- Power on, holding reset until the power LED blinks slowly
- Visit http://192.168.1.1/ and upload OpenWrt factory image
- Wait at least 5 minutes for flashing, reboot and key generation
- Visit http://192.168.1.1/ (OpenWrt LuCI) and upload OpenWrt sysupgrade image
Signed-off-by: Ryan Mounce <ryan at mounce.com.au>
[dt leds preparations]
Signed-off-by: Christian Lamparter <chunkeey at gmail.com>
---
target/linux/ath79/dts/ar9344_wd_mynet-n600.dts | 108 +++++++++++++++++++++
target/linux/ath79/dts/ar9344_wd_mynet-n750.dts | 89 +----------------
target/linux/ath79/dts/ar9344_wd_mynet-nxxx.dtsi | 88 +++++++++++++++++
.../generic/base-files/etc/board.d/02_network | 4 +-
.../etc/hotplug.d/firmware/10-ath9k-eeprom | 2 +
target/linux/ath79/image/generic.mk | 12 +++
6 files changed, 216 insertions(+), 87 deletions(-)
diff --git a/target/linux/ath79/dts/ar9344_wd_mynet-n600.dts b/target/linux/ath79/dts/ar9344_wd_mynet-n600.dts
new file mode 100644
index 0000000000..81788fb348
--- /dev/null
+++ b/target/linux/ath79/dts/ar9344_wd_mynet-n600.dts
@@ -0,0 +1,108 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9344_wd_mynet-nxxx.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Western Digital My Net N600";
+ compatible = "wd,mynet-n600", "qca,ar9344";
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_WLAN;
+ gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_power: led-1 {
+ label = "blue:power";
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_POWER;
+ gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-2 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_WAN;
+ gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-3 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_WPS;
+ gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&gpio {
+ gpio_ext_lna0 {
+ gpio-hog;
+ gpios = <14 0>;
+ output-high;
+ line-name = "ext:lna0";
+ };
+
+ gpio_ext_lna1 {
+ gpio-hog;
+ gpios = <15 0>;
+ output-high;
+ line-name = "ext:lna1";
+ };
+};
+
+&pinmux {
+ pmx_led_switch: pinmux_led_switch {
+ pinctrl-single,bits =
+ <0x0 0x2c2b2a00 0xffffff00>, /* GPIO1-3 default to PHY2-4 */
+ <0x4 0x00000029 0x000000ff>; /* GPIO4 default to PHY1 */
+ };
+};
+
+&builtin_switch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmx_led_switch>;
+};
+
+&usb {
+ status = "okay";
+};
+
+ð0 {
+ status = "okay";
+
+ phy-handle = <&swphy0>;
+
+ gmac-config {
+ device = <&gmac>;
+ switch-phy-swap = <1>;
+ switch-only-mode = <1>;
+ };
+};
+
+ð1 {
+ status = "okay";
+};
diff --git a/target/linux/ath79/dts/ar9344_wd_mynet-n750.dts b/target/linux/ath79/dts/ar9344_wd_mynet-n750.dts
index e3faa392a8..d1f63c5064 100644
--- a/target/linux/ath79/dts/ar9344_wd_mynet-n750.dts
+++ b/target/linux/ath79/dts/ar9344_wd_mynet-n750.dts
@@ -1,18 +1,11 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-#include "ar9344.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "ar9344_wd_mynet-nxxx.dtsi"
/ {
model = "Western Digital My Net N750";
compatible = "wd,mynet-n750", "qca,ar9344";
- chosen {
- bootargs = "console=ttyS0,115200n8";
- };
-
aliases {
led-boot = &led_power;
led-failsafe = &led_power;
@@ -59,75 +52,19 @@
};
};
-&ref {
- clock-frequency = <40000000>;
-};
-
&gpio {
gpio_ext_lna0 {
gpio-hog;
gpios = <15 0>;
output-high;
- line-name = "mynet-n750:ext:lna0";
+ line-name = "ext:lna0";
};
gpio_ext_lna1 {
gpio-hog;
gpios = <18 0>;
output-high;
- line-name = "mynet-n750:ext:lna1";
- };
-};
-
-&spi {
- status = "okay";
-
- flash at 0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <25000000>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition at 0 {
- label = "bootloader";
- reg = <0x000000 0x40000>;
- read-only;
- };
-
- partition at 40000 {
- label = "bdcfg";
- reg = <0x040000 0x10000>;
- read-only;
- };
-
- partition at 50000 {
- label = "devdata";
- reg = <0x050000 0x10000>;
- read-only;
- };
-
- partition at 60000 {
- label = "devconf";
- reg = <0x060000 0x10000>;
- read-only;
- };
-
- partition at 70000 {
- compatible = "seama";
- label = "firmware";
- reg = <0x070000 0xf80000>;
- };
-
- art: partition at ff0000 {
- label = "art";
- reg = <0xff0000 0x010000>;
- read-only;
- };
- };
+ line-name = "ext:lna1";
};
};
@@ -154,26 +91,6 @@
};
};
-&usb_phy {
- status = "okay";
-};
-
-&pcie {
- status = "okay";
-
- wifi at 0,0 {
- compatible = "pci168c,0033";
- reg = <0x0000 0 0 0 0>;
- qca,no-eeprom;
- };
-};
-
-&wmac {
- status = "okay";
-
- qca,no-eeprom;
-};
-
&mdio0 {
status = "okay";
diff --git a/target/linux/ath79/dts/ar9344_wd_mynet-nxxx.dtsi b/target/linux/ath79/dts/ar9344_wd_mynet-nxxx.dtsi
new file mode 100644
index 0000000000..73e2c2566f
--- /dev/null
+++ b/target/linux/ath79/dts/ar9344_wd_mynet-nxxx.dtsi
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9344.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ };
+};
+
+&ref {
+ clock-frequency = <40000000>;
+};
+
+&spi {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "bootloader";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "bdcfg";
+ reg = <0x040000 0x010000>;
+ read-only;
+ };
+
+ partition at 50000 {
+ label = "devdata";
+ reg = <0x050000 0x010000>;
+ read-only;
+ };
+
+ partition at 60000 {
+ label = "devconf";
+ reg = <0x060000 0x010000>;
+ read-only;
+ };
+
+ partition at 70000 {
+ compatible = "seama";
+ label = "firmware";
+ reg = <0x070000 0xf80000>;
+ };
+
+ art: partition at ff0000 {
+ label = "art";
+ reg = <0xff0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&pcie {
+ status = "okay";
+
+ wifi at 0,0 {
+ compatible = "pci168c,0033";
+ reg = <0x0000 0 0 0 0>;
+ qca,no-eeprom;
+ };
+};
+
+&wmac {
+ status = "okay";
+
+ qca,no-eeprom;
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index 45b002330e..edd79b606e 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -130,7 +130,8 @@ ath79_setup_interfaces()
pcs,cr3000|\
tplink,archer-c58-v1|\
tplink,archer-c59-v1|\
- tplink,archer-c59-v2)
+ tplink,archer-c59-v2|\
+ wd,mynet-n600)
ucidef_set_interface_wan "eth1"
ucidef_add_switch "switch0" \
"0 at eth0" "1:lan:1" "2:lan:4" "3:lan:3" "4:lan:2"
@@ -595,6 +596,7 @@ ath79_setup_macs()
;;
dlink,dir-859-a1|\
qihoo,c301|\
+ wd,mynet-n600|\
wd,mynet-n750)
lan_mac=$(mtd_get_mac_ascii devdata "lanmac")
wan_mac=$(mtd_get_mac_ascii devdata "wanmac")
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index da78e74dcb..219e618cb9 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -30,6 +30,7 @@ case "$FIRMWARE" in
dlink,dir-859-a1|\
nec,wf1200cr|\
nec,wg1200cr|\
+ wd,mynet-n600|\
wd,mynet-n750)
caldata_extract "art" 0x1000 0x440
ath9k_patch_mac $(mtd_get_mac_ascii devdata "wlan24mac")
@@ -126,6 +127,7 @@ case "$FIRMWARE" in
openmesh,mr600-v2)
caldata_extract "ART" 0x5000 0x440
;;
+ wd,mynet-n600|\
wd,mynet-n750)
caldata_extract "art" 0x5000 0x440
ath9k_patch_mac $(mtd_get_mac_ascii devdata "wlan5mac")
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index cff4b98eae..ff24764740 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -2336,6 +2336,18 @@ define Device/wallys_dr531
endef
TARGET_DEVICES += wallys_dr531
+define Device/wd_mynet-n600
+ $(Device/seama)
+ SOC := ar9344
+ DEVICE_VENDOR := Western Digital
+ DEVICE_MODEL := My Net N600
+ IMAGE_SIZE := 15872k
+ DEVICE_PACKAGES := kmod-usb2
+ SEAMA_SIGNATURE := wrgnd16_wd_db600
+ SUPPORTED_DEVICES += mynet-n600
+endef
+TARGET_DEVICES += wd_mynet-n600
+
define Device/wd_mynet-n750
$(Device/seama)
SOC := ar9344
More information about the lede-commits
mailing list