[openwrt/openwrt] ath79: add support for GL.iNet GL-X300B
LEDE Commits
lede-commits at lists.infradead.org
Wed Aug 4 16:48:28 PDT 2021
blocktrron pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/252466a0ced3ec9f58b213ffd34a900fe3834cab
commit 252466a0ced3ec9f58b213ffd34a900fe3834cab
Author: John Marrett <johnf at zioncluster.ca>
AuthorDate: Tue Jun 8 12:57:28 2021 -0400
ath79: add support for GL.iNet GL-X300B
The GL-X300B is a industrial 4G LTE router based on the Qualcomm
QCA9531 SoC.
Specifications:
- Qualcomm QCA9531 @ 650 MHz
- 128 MB of RAM
- 16 MB of SPI NOR FLASH
- 2x 10/100 Mbps Ethernet
- 2.4GHz 802.11b/g/n
- 1x USB 2.0 (vbus driven by GPIO)
- 4x LED, driven by GPIO
- 1x button (reset)
- 1x mini pci-e slot (vcc driven by GPIO)
- RS-485 Serial Port (untested)
Flash instructions:
This firmware can be flashed using either sysupgrade from the GL.iNet
firmware or the recovery console as follows:
- Press and hold the reset button
- Connect power to the router, wait five seconds
- Manually configure 192.168.1.2/24 on your computer, connect to
192.168.1.1
- Upload the firmware image using the web interface
RS-485 serial port is untested and may depend on the following commit in
the GL.iNet repo:
https://github.com/gl-inet/openwrt/commit/202e83a32ae308fbb70502b6dbe3bb0bf8b1fba9
MAC addresses as verified by OEM firmware:
vendor OpenWrt address
WAN eth0 label
LAN eth1 label + 1
2g phy0 label + 2
The label MAC address was found in the art partition at 0x0
Based on vendor commit:
https://github.com/gl-inet/openwrt/commit/16c5708b207eb76ff19a040dc973e560d3d8074b
Signed-off-by: John Marrett <johnf at zioncluster.ca>
---
target/linux/ath79/dts/qca9531_glinet_gl-x300b.dts | 139 +++++++++++++++++++++
.../ath79/generic/base-files/etc/board.d/01_leds | 1 +
.../generic/base-files/etc/board.d/02_network | 5 +
target/linux/ath79/image/generic.mk | 9 ++
4 files changed, 154 insertions(+)
diff --git a/target/linux/ath79/dts/qca9531_glinet_gl-x300b.dts b/target/linux/ath79/dts/qca9531_glinet_gl-x300b.dts
new file mode 100644
index 0000000000..5e722bbc26
--- /dev/null
+++ b/target/linux/ath79/dts/qca9531_glinet_gl-x300b.dts
@@ -0,0 +1,139 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca953x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "glinet,gl-x300b", "qca,qca9531";
+ model = "GL.iNet GL-X300B";
+
+ keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&jtag_disable_pins>;
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ wlan2g {
+ label = "green:wlan2g";
+ gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wan {
+ label = "green:wan";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ };
+
+ lte {
+ label = "green:lte";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-export {
+ compatible = "gpio-export";
+
+ minipcie {
+ gpio-export,name = "minipcie";
+ gpio-export,output = <0>;
+ gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ rs485tx_en {
+ gpio-export,name = "rs485tx_en";
+ gpio-export,output = <0>;
+ gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ ble_rst {
+ gpio-export,name = "ble_rst";
+ gpio-export,output = <0>;
+ gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ watchdog {
+ compatible = "hw_wdt";
+ dog_en_gpio = <12>;
+ feed_dog_gpio = <2>;
+ feed_dog_interval = <100000000>;
+ };
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&spi {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ nor_partitions: partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "u-boot-env";
+ reg = <0x040000 0x010000>;
+ };
+
+ art: partition at 50000 {
+ label = "art";
+ reg = <0x050000 0x010000>;
+ read-only;
+ };
+
+ partition at 60000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x060000 0xfa0000>;
+ };
+
+ };
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ mtd-mac-address = <&art 0x0>;
+ phy-handle = <&swphy4>;
+};
+
+ð1 {
+ mtd-mac-address = <&art 0x0>;
+ mtd-mac-address-increment = <1>;
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index 8fa8b48562..7a07b0ce6d 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -219,6 +219,7 @@ qxwlan,e750a-v4-16m)
ucidef_set_led_switch "lan" "LAN" "green:lan" "switch0" "0x02"
ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth1"
;;
+glinet,gl-x300b|\
glinet,gl-x750)
ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth1"
;;
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index af8619845b..4fe7fbc027 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -272,6 +272,11 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0 at eth0" "1:lan" "2:lan"
;;
+ glinet,gl-x300b)
+ ucidef_set_interface_wan "eth1"
+ ucidef_add_switch "switch0" \
+ "0 at eth0" "4:lan"
+ ;;
iodata,etg3-r|\
iodata,wn-ac1167dgr|\
iodata,wn-ac1600dgr|\
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index b33a578f19..2abe1b7307 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -1243,6 +1243,15 @@ define Device/glinet_gl-usb150
endef
TARGET_DEVICES += glinet_gl-usb150
+define Device/glinet_gl-x300b
+ SOC := qca9531
+ DEVICE_VENDOR := GL.iNet
+ DEVICE_MODEL := GL-X300B
+ DEVICE_PACKAGES := kmod-usb2
+ IMAGE_SIZE := 16000k
+endef
+TARGET_DEVICES += glinet_gl-x300b
+
define Device/glinet_gl-x750
SOC := qca9531
DEVICE_VENDOR := GL.iNet
More information about the lede-commits
mailing list