[PATCH v5 7/8] iommu/amd: Don't update domain info to dte entry at iommu init stage

[Baoquan He]

On 09/21/16 at 06:26pm, Baoquan He wrote:
> On 09/20/16 at 02:50pm, Joerg Roedel wrote:
> > On Thu, Sep 15, 2016 at 11:03:25PM +0800, Baoquan He wrote:
> > > AMD iommu creates protection domain and assign each device to it during
> > > iommu driver initialization stage. This happened just after system pci
> > > bus scanning stage, and much earlier than device driver init stage. So
> > > at this time if in kdump kernel the domain info, especially pte_root,
> > > can't be updated to dte entry. We should wait until device driver init
> > > stage.
> > > 
> > > Signed-off-by: Baoquan He <bhe at redhat.com>
> > > ---
> > >  drivers/iommu/amd_iommu.c | 18 ++++++++++++++++++
> > >  1 file changed, 18 insertions(+)
> > > 
> > > diff --git a/drivers/iommu/amd_iommu.c b/drivers/iommu/amd_iommu.c
> > > index fcb69ff..6c37300 100644
> > > --- a/drivers/iommu/amd_iommu.c
> > > +++ b/drivers/iommu/amd_iommu.c
> > > @@ -137,6 +137,7 @@ struct iommu_dev_data {
> > >  	bool pri_tlp;			  /* PASID TLB required for
> > >  					     PPR completions */
> > >  	u32 errata;			  /* Bitmap for errata to apply */
> > > +	bool domain_updated;
> > >  };
> > >  
> > >  /*
> > > @@ -1708,6 +1709,15 @@ static void set_dte_entry(u16 devid, struct protection_domain *domain, bool ats)
> > >  {
> > >  	u64 pte_root = 0;
> > >  	u64 flags = 0;
> > > +	struct iommu_dev_data *dev_data;
> > > +	struct amd_iommu *iommu = amd_iommu_rlookup_table[devid];
> > > +
> > > +	dev_data = find_dev_data(devid);
> > > +        if (!dev_data)
> > > +                return;
> > > +
> > > +	if (translation_pre_enabled(iommu) && !dev_data->domain_updated)
> > > +		return;
> > >  
> > >  	if (domain->mode != PAGE_MODE_NONE)
> > >  		pte_root = virt_to_phys(domain->pt_root);
> > > @@ -1756,6 +1766,14 @@ static void set_dte_entry(u16 devid, struct protection_domain *domain, bool ats)
> > >  
> > >  static void clear_dte_entry(u16 devid)
> > >  {
> > > +	struct iommu_dev_data *dev_data;
> > > +	struct amd_iommu *iommu = amd_iommu_rlookup_table[devid];
> > > +
> > > +	dev_data = find_dev_data(devid);
> > > +        if (!dev_data)
> > > +                return;
> > > +	if (translation_pre_enabled(iommu) && !dev_data->domain_updated)
> > > +		return;
> > 
> > This should be moved to do_attach/do_detach. There you also already have
> > the dev_data you need here.
> 
> For amd-vi v1, checking in do_attach/do_detach is enough. But for v2
> amd_iommu_domain_direct_map and amd_iommu_domain_enable_v2 also call it
Here I means amd_iommu_domain_direct_map and amd_iommu_domain_enable_v2
will call set_dte_entry to change pte_root setting.

> to install pte_root into dev table. So finally, I move them into these
> two lowest level functions to prevent any pte_root changing during iommu
> init stage. It involves the least code change.
> 
> > 
> > >  	/* remove entry from the device table seen by the hardware */
> > >  	amd_iommu_dev_table[devid].data[0]  = DTE_FLAG_V | DTE_FLAG_TV;
> > >  	amd_iommu_dev_table[devid].data[1] &= DTE_FLAG_MASK;
> > > -- 
> > > 2.5.5
> > >