WPA Supplicant, Ad-Hoc network WPA-PSK with Raspberry Pi 3

Greg Gigon greg.gigon at gmail.com
Thu Oct 27 17:12:30 PDT 2016


Hi All
I tried many forums and this mailing list is my last hope.
I am trying to setup secure wireless ad-hoc network between 2 Raspberry Pi’s 3 using their on board Wireless chip.

I’m following https://wiki.archlinux.org/index.php/Ad-hoc_networking instructions to get it to work but I can’t get wpa_supplicant to setup secure network.
I have succeeded setting up the non secured ad-hoc network between 2 Raspberry Pi’s 3 with no issues.

My Wpa supplicant config file looks like this:

ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
update_config=1
ap_scan=2
network={
        ssid="FooBar"
        mode=1
        frequency=2462
        proto=RSN
        key_mgmt=WPA-PSK
        pairwise=CCMP
        group=CCMP
        psk=“foobarpass"
}

I’m running the supplicant with command: sudo wpa_supplicant -i wlan0 -c /etc/wpa_supplicant/wpa_supp.conf -D nl80211 -d

Same setup on both Devices. Bellow is the output. 
Any pointer towards where to start looking at will save me some hair pulling :)
Greg

Kernel Linux 4.4.21-v7+ #911 SMP Thu Sep 15 14:22:38 BST 2016 armv7l GNU/Linux
Loaded modules:
Module                  Size  Used by
bnep                   10340  2
hci_uart               17943  1
btbcm                   5929  1 hci_uart
bluetooth             326105  22 bnep,btbcm,hci_uart
brcmfmac              186339  0
brcmutil                5661  1 brcmfmac
cfg80211              427855  1 brcmfmac
rfkill                 16037  3 cfg80211,bluetooth
snd_bcm2835            20447  0
snd_pcm                75762  1 snd_bcm2835
snd_timer              19288  1 snd_pcm
snd                    51908  3 snd_bcm2835,snd_timer,snd_pcm
bcm2835_wdt             3225  0
bcm2835_gpiomem         3040  0
uio_pdrv_genirq         3164  0
uio                     8000  1 uio_pdrv_genirq
md_mod                118571  0
i2c_dev                 5859  0
fuse                   83653  1
ipv6                  347466  36

First PI to be started:
pi at raspberrypi3bare:~ $ sudo wpa_supplicant -i wlan0 -c /etc/wpa_supplicant/wpa_supp.conf -D nl80211 -dd
wpa_supplicant v2.6
random: Trying to read entropy from /dev/random
Successfully initialized wpa_supplicant
Initializing interface 'wlan0' conf '/etc/wpa_supplicant/wpa_supp.conf' driver 'nl80211' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supp.conf' -> '/etc/wpa_supplicant/wpa_supp.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supp.conf'
ctrl_interface='DIR=/var/run/wpa_supplicant GROUP=netdev'
update_config=1
ap_scan=2
Line: 4 - start of a new network block
ssid - hexdump_ascii(len=6):
     46 6f 6f 42 61 72                                 FooBar
mode=1 (0x1)
frequency=2462 (0x99e)
proto: 0x2
key_mgmt: 0x2
pairwise: 0x10
group: 0x10
PSK (ASCII passphrase) - hexdump_ascii(len=8): [REMOVED]
PSK (from passphrase) - hexdump(len=32): [REMOVED]
Priority group 0
   id=0 ssid='FooBar'
nl80211: TDLS supported
nl80211: Supported cipher 00-0f-ac:1
nl80211: Supported cipher 00-0f-ac:5
nl80211: Supported cipher 00-0f-ac:2
nl80211: Supported cipher 00-0f-ac:4
nl80211: Supported cipher 00-0f-ac:6
nl80211: Using driver-based off-channel TX
nl80211: Supported vendor command: vendor_id=0x1018 subcmd=1
nl80211: Use separate P2P group interface (driver advertised support)
nl80211: Enable multi-channel concurrent (driver advertised support)
nl80211: use P2P_DEVICE support
nl80211: interface wlan0 in phy phy0
nl80211: Set mode ifindex 3 iftype 2 (STATION)
nl80211: Subscribe to mgmt frames with non-AP handle 0x6fe670
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x6fe670 match=06
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x6fe670 match=0a07
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x6fe670 match=0a11
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x6fe670 match=1101
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x6fe670 match=1102
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x6fe670 match=0505
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x6fe670 match=0500
rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0
netlink: Operstate: ifindex=3 linkmode=1 (userspace-control), operstate=5 (IF_OPER_DORMANT)
Add interface wlan0 to a new radio phy0
nl80211: Regulatory information - country=00
nl80211: 2402-2472 @ 40 MHz 20 mBm
nl80211: 2457-2482 @ 40 MHz 20 mBm (no IR)
nl80211: 2474-2494 @ 20 MHz 20 mBm (no OFDM) (no IR)
nl80211: 5170-5250 @ 80 MHz 20 mBm (no IR)
nl80211: 5250-5330 @ 80 MHz 20 mBm (DFS) (no IR)
nl80211: 5490-5730 @ 160 MHz 20 mBm (DFS) (no IR)
nl80211: 5735-5835 @ 80 MHz 20 mBm (no IR)
nl80211: 57240-63720 @ 2160 MHz 0 mBm
nl80211: Added 802.11b mode based on 802.11g information
wlan0: Own MAC address: b8:27:eb:2b:85:ff
Note: nl80211 driver interface is not designed to be used with ap_scan=2; this can result in connection failures
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=3 set_tx=0 seq_len=0 key_len=0
wlan0: RSN: flushing PMKID list in the driver
nl80211: Flush PMKIDs
ENGINE: Loading dynamic engine
ENGINE: Loading dynamic engine
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
nl80211: Skip set_supp_port(unauthorized) while not associated
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
ctrl_interface_group=108 (from group name 'netdev')
wlan0: Added interface wlan0
wlan0: State: DISCONNECTED -> DISCONNECTED
nl80211: Set wlan0 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
random: Got 20/20 bytes from /dev/random
RTM_NEWLINK: ifi_index=3 ifname=wlan0 operstate=2 linkmode=1 ifi_family=0 ifi_flags=0x1003 ([UP])
wlan0: Starting delayed sched scan
wlan0: Use normal scan instead of sched_scan for initial scans (normal_scans=0)
wlan0: Setting scan request: 0.000000 sec
wlan0: State: DISCONNECTED -> SCANNING
wlan0: Add radio work 'connect'@0x70d5d0
wlan0: First radio work item in the queue - schedule start immediately
wlan0: Starting radio work 'connect'@0x70d5d0 after 0.000055 second wait
wlan0: Trying to associate with SSID 'FooBar'
wlan0: Cancelling scan request
wlan0: WPA: clearing own WPA/RSN IE
wlan0: Automatic auth_alg selection: 0x1
wlan0: WPA: No WPA/RSN IE available from association info
wlan0: WPA: Set cipher suites based on configuration
wlan0: WPA: Selected cipher suites: group 16 pairwise 16 key_mgmt 2 proto 2
wlan0: WPA: clearing AP WPA IE
wlan0: WPA: clearing AP RSN IE
wlan0: WPA: using GTK CCMP
wlan0: WPA: using PTK CCMP
wlan0: WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
wlan0: State: SCANNING -> ASSOCIATING
nl80211: Set wlan0 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
nl80211: Join IBSS (ifindex=3)
nl80211: Set mode ifindex 3 iftype 1 (ADHOC)
nl80211: Unsubscribe mgmt frames handle 0x88e76ef9 (mode change)
nl80211: Subscribe to mgmt frames with non-AP handle 0x6fe670
nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x6fe670 match=
nl80211: Register frame command failed (type=176): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x6fe670 match=06
nl80211: Register frame command failed (type=208): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=1): 06
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x6fe670 match=0a07
nl80211: Register frame command failed (type=208): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=2): 0a 07
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x6fe670 match=0a11
nl80211: Register frame command failed (type=208): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=2): 0a 11
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x6fe670 match=1101
nl80211: Register frame command failed (type=208): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=2): 11 01
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x6fe670 match=1102
nl80211: Register frame command failed (type=208): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=2): 11 02
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x6fe670 match=0505
nl80211: Register frame command failed (type=208): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=2): 05 05
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x6fe670 match=0500
nl80211: Register frame command failed (type=208): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=2): 05 00
nl80211: Failed to register Action frame processing - ignore for now
  * SSID - hexdump_ascii(len=6):
     46 6f 6f 42 61 72                                 FooBar
  * freq=2462
  * vht_enabled=0
  * ht_enabled=0
  * channel_type=0
  * control port
  * Extra IEs for Beacon/Probe Response frames - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
nl80211: Join IBSS request sent successfully
wlan0: Setting authentication timeout: 60 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
RTM_NEWLINK: ifi_index=3 ifname=wlan0 wext ifi_family=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK: ifi_index=3 ifname=wlan0 operstate=5 linkmode=1 ifi_family=0 ifi_flags=0x11003 ([UP][LOWER_UP])
nl80211: Event message available
nl80211: Drv Event 43 (NL80211_CMD_JOIN_IBSS) received for wlan0
nl80211: IBSS 32:59:05:91:a6:e2 joined
nl80211: IBSS-joined on 2462 MHz
nl80211: Operating frequency for the associated BSS from scan results: 2462 MHz
nl80211: IBSS on frequency 2462 MHz
wlan0: Event ASSOC (0) received
wlan0: Association info event
wlan0: freq=2462 MHz
wlan0: State: ASSOCIATING -> ASSOCIATED
nl80211: Set wlan0 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
wlan0: Associated to a new BSS: BSSID=32:59:05:91:a6:e2
wlan0: Select network based on association information
wlan0: Network configuration found for the current AP
wlan0: WPA: Using WPA IE from AssocReq to set cipher suites
wlan0: WPA: Selected cipher suites: group 16 pairwise 16 key_mgmt 2 proto 2
wlan0: WPA: clearing AP WPA IE
wlan0: WPA: clearing AP RSN IE
wlan0: WPA: using GTK CCMP
wlan0: WPA: using PTK CCMP
wlan0: WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
nl80211: IBSS-joined on 2462 MHz
nl80211: Received scan results (1 BSSes)
wlan0: BSS: Start scan result update 1
wlan0: BSS: Add new id 0 BSSID 32:59:05:91:a6:e2 SSID 'FooBar' freq 2462
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
wlan0: Associated with 32:59:05:91:a6:e2
wlan0: WPA: Association event - clear replay counter
wlan0: WPA: Clear old PTK
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
wlan0: Cancelling authentication timeout
wlan0: State: ASSOCIATED -> COMPLETED
wlan0: Radio work 'connect'@0x70d5d0 done in 0.522230 seconds
wlan0: radio_work_free('connect'@0x70d5d0: num_active_works --> 0
wlan0: CTRL-EVENT-CONNECTED - Connection to 32:59:05:91:a6:e2 completed [id=0 id_str=]
nl80211: Set wlan0 operstate 0->1 (UP)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
wlan0: Cancelling scan request
WMM AC: Missing IEs
wlan0: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
RTM_NEWLINK: ifi_index=3 ifname=wlan0 operstate=6 linkmode=1 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
RTM_NEWLINK: ifi_index=3 ifname=wlan0 operstate=6 linkmode=1 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
EAPOL: startWhen --> 0
EAPOL: disable timer tick
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: enable timer tick
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)
EAPOL: startWhen --> 0
EAPOL: disable timer tick
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: enable timer tick
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)


Second PI:
pi at raspberrypi3black:~ $ sudo wpa_supplicant -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf -D nl80211 -dd
wpa_supplicant v2.6
random: Trying to read entropy from /dev/random
Successfully initialized wpa_supplicant
Initializing interface 'wlan0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'nl80211' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
ctrl_interface='DIR=/var/run/wpa_supplicant GROUP=netdev'
update_config=1
ap_scan=2
Line: 4 - start of a new network block
ssid - hexdump_ascii(len=6):
     46 6f 6f 42 61 72                                 FooBar
mode=1 (0x1)
frequency=2462 (0x99e)
proto: 0x2
key_mgmt: 0x2
pairwise: 0x10
group: 0x10
PSK (ASCII passphrase) - hexdump_ascii(len=8): [REMOVED]
PSK (from passphrase) - hexdump(len=32): [REMOVED]
Priority group 0
   id=0 ssid='FooBar'
nl80211: TDLS supported
nl80211: Supported cipher 00-0f-ac:1
nl80211: Supported cipher 00-0f-ac:5
nl80211: Supported cipher 00-0f-ac:2
nl80211: Supported cipher 00-0f-ac:4
nl80211: Supported cipher 00-0f-ac:6
nl80211: Using driver-based off-channel TX
nl80211: Supported vendor command: vendor_id=0x1018 subcmd=1
nl80211: Use separate P2P group interface (driver advertised support)
nl80211: Enable multi-channel concurrent (driver advertised support)
nl80211: use P2P_DEVICE support
nl80211: interface wlan0 in phy phy0
nl80211: Set mode ifindex 3 iftype 2 (STATION)
nl80211: Subscribe to mgmt frames with non-AP handle 0x57b678
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=06
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=0a07
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=0a11
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=1101
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=1102
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=0505
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=0500
rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0
netlink: Operstate: ifindex=3 linkmode=1 (userspace-control), operstate=5 (IF_OPER_DORMANT)
Add interface wlan0 to a new radio phy0
nl80211: Regulatory information - country=00
nl80211: 2402-2472 @ 40 MHz 20 mBm
nl80211: 2457-2482 @ 40 MHz 20 mBm (no IR)
nl80211: 2474-2494 @ 20 MHz 20 mBm (no OFDM) (no IR)
nl80211: 5170-5250 @ 80 MHz 20 mBm (no IR)
nl80211: 5250-5330 @ 80 MHz 20 mBm (DFS) (no IR)
nl80211: 5490-5730 @ 160 MHz 20 mBm (DFS) (no IR)
nl80211: 5735-5835 @ 80 MHz 20 mBm (no IR)
nl80211: 57240-63720 @ 2160 MHz 0 mBm
nl80211: Added 802.11b mode based on 802.11g information
wlan0: Own MAC address: b8:27:eb:83:26:44
Note: nl80211 driver interface is not designed to be used with ap_scan=2; this can result in connection failures
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=3 set_tx=0 seq_len=0 key_len=0
wlan0: RSN: flushing PMKID list in the driver
nl80211: Flush PMKIDs
ENGINE: Loading dynamic engine
ENGINE: Loading dynamic engine
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
nl80211: Skip set_supp_port(unauthorized) while not associated
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
ctrl_interface_group=108 (from group name 'netdev')
wlan0: Added interface wlan0
wlan0: State: DISCONNECTED -> DISCONNECTED
nl80211: Set wlan0 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
random: Got 20/20 bytes from /dev/random
RTM_NEWLINK: ifi_index=3 ifname=wlan0 operstate=2 linkmode=1 ifi_family=0 ifi_flags=0x1003 ([UP])
wlan0: Starting delayed sched scan
wlan0: Use normal scan instead of sched_scan for initial scans (normal_scans=0)
wlan0: Setting scan request: 0.000000 sec
wlan0: State: DISCONNECTED -> SCANNING
wlan0: Add radio work 'connect'@0x58a5d8
wlan0: First radio work item in the queue - schedule start immediately
wlan0: Starting radio work 'connect'@0x58a5d8 after 0.000023 second wait
wlan0: Trying to associate with SSID 'FooBar'
wlan0: Cancelling scan request
wlan0: WPA: clearing own WPA/RSN IE
wlan0: Automatic auth_alg selection: 0x1
wlan0: WPA: No WPA/RSN IE available from association info
wlan0: WPA: Set cipher suites based on configuration
wlan0: WPA: Selected cipher suites: group 16 pairwise 16 key_mgmt 2 proto 2
wlan0: WPA: clearing AP WPA IE
wlan0: WPA: clearing AP RSN IE
wlan0: WPA: using GTK CCMP
wlan0: WPA: using PTK CCMP
wlan0: WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
wlan0: State: SCANNING -> ASSOCIATING
nl80211: Set wlan0 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
nl80211: Join IBSS (ifindex=3)
nl80211: Set mode ifindex 3 iftype 1 (ADHOC)
nl80211: Unsubscribe mgmt frames handle 0x88df3ef1 (mode change)
nl80211: Subscribe to mgmt frames with non-AP handle 0x57b678
nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x57b678 match=
nl80211: Register frame command failed (type=176): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=06
nl80211: Register frame command failed (type=208): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=1): 06
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=0a07
nl80211: Register frame command failed (type=208): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=2): 0a 07
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=0a11
nl80211: Register frame command failed (type=208): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=2): 0a 11
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=1101
nl80211: Register frame command failed (type=208): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=2): 11 01
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=1102
nl80211: Register frame command failed (type=208): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=2): 11 02
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=0505
nl80211: Register frame command failed (type=208): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=2): 05 05
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=0500
nl80211: Register frame command failed (type=208): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=2): 05 00
nl80211: Failed to register Action frame processing - ignore for now
  * SSID - hexdump_ascii(len=6):
     46 6f 6f 42 61 72                                 FooBar
  * freq=2462
  * vht_enabled=0
  * ht_enabled=0
  * channel_type=0
  * control port
  * Extra IEs for Beacon/Probe Response frames - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
nl80211: Join IBSS request sent successfully
wlan0: Setting authentication timeout: 60 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
nl80211: Event message available
nl80211: Drv Event 43 (NL80211_CMD_JOIN_IBSS) received for wlan0
nl80211: IBSS 32:59:05:91:a6:e2 joined
nl80211: IBSS-joined on 2462 MHz
nl80211: Operating frequency for the associated BSS from scan results: 2462 MHz
nl80211: IBSS on frequency 2462 MHz
wlan0: Event ASSOC (0) received
wlan0: Association info event
wlan0: freq=2462 MHz
wlan0: State: ASSOCIATING -> ASSOCIATED
nl80211: Set wlan0 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
wlan0: Associated to a new BSS: BSSID=32:59:05:91:a6:e2
wlan0: Select network based on association information
wlan0: Network configuration found for the current AP
wlan0: WPA: Using WPA IE from AssocReq to set cipher suites
wlan0: WPA: Selected cipher suites: group 16 pairwise 16 key_mgmt 2 proto 2
wlan0: WPA: clearing AP WPA IE
wlan0: WPA: clearing AP RSN IE
wlan0: WPA: using GTK CCMP
wlan0: WPA: using PTK CCMP
wlan0: WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
nl80211: IBSS-joined on 2462 MHz
nl80211: Received scan results (1 BSSes)
wlan0: BSS: Start scan result update 1
wlan0: BSS: Add new id 0 BSSID 32:59:05:91:a6:e2 SSID 'FooBar' freq 2462
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
wlan0: Associated with 32:59:05:91:a6:e2
wlan0: WPA: Association event - clear replay counter
wlan0: WPA: Clear old PTK
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
wlan0: Cancelling authentication timeout
wlan0: State: ASSOCIATED -> COMPLETED
wlan0: Radio work 'connect'@0x58a5d8 done in 0.605994 seconds
wlan0: radio_work_free('connect'@0x58a5d8: num_active_works --> 0
wlan0: CTRL-EVENT-CONNECTED - Connection to 32:59:05:91:a6:e2 completed [id=0 id_str=]
nl80211: Set wlan0 operstate 0->1 (UP)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
wlan0: Cancelling scan request
WMM AC: Missing IEs
wlan0: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
RTM_NEWLINK: ifi_index=3 ifname=wlan0 wext ifi_family=0 ifi_flags=0x11003 ([UP][LOWER_UP])
nl80211: Set IF_OPER_UP again based on ifi_flags and expected operstate
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
RTM_NEWLINK: ifi_index=3 ifname=wlan0 operstate=5 linkmode=1 ifi_family=0 ifi_flags=0x11003 ([UP][LOWER_UP])
nl80211: Set IF_OPER_UP again based on ifi_flags and expected operstate
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
RTM_NEWLINK: ifi_index=3 ifname=wlan0 operstate=6 linkmode=1 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
RTM_NEWLINK: ifi_index=3 ifname=wlan0 operstate=6 linkmode=1 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
EAPOL: startWhen --> 0
EAPOL: disable timer tick
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: enable timer tick
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)
EAPOL: startWhen --> 0
EAPOL: disable timer tick
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: enable timer tick
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)
EAPOL: startWhen --> 0
EAPOL: disable timer tick
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: enable timer tick
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)
EAPOL: startWhen --> 0
EAPOL: disable timer tick
EAPOL: SUPP_PAE entering state HELD
EAPOL: enable timer tick
EAPOL: Supplicant port status: Unauthorized
nl80211: Set supplicant port unauthorized for 32:59:05:91:a6:e2
EAPOL authentication completed - result=FAILURE
wlan0: Setting authentication timeout: 2 sec 0 usec
wlan0: Authentication with 32:59:05:91:a6:e2 timed out.
Added BSSID 32:59:05:91:a6:e2 into blacklist
wlan0: WPA: Clear old PMK and PTK
wlan0: Request to deauthenticate - bssid=32:59:05:91:a6:e2 pending_bssid=00:00:00:00:00:00 reason=3 state=COMPLETED
nl80211: Leave IBSS request sent successfully
nl80211: Set mode ifindex 3 iftype 2 (STATION)
nl80211: Unsubscribe mgmt frames handle 0x88df3ef1 (mode change)
nl80211: Subscribe to mgmt frames with non-AP handle 0x57b678
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=06
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=0a07
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=0a11
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=1101
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=1102
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=0505
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=0500
wlan0: Event DEAUTH (12) received
wlan0: Deauthentication notification
wlan0:  * reason 3 (locally generated)
Deauthentication frame IE(s) - hexdump(len=0): [NULL]
wlan0: CTRL-EVENT-DISCONNECTED bssid=32:59:05:91:a6:e2 reason=3 locally_generated=1
wlan0: Auto connect enabled: try to reconnect (wps=0/0 wpa_state=9)
wlan0: Setting scan request: 0.100000 sec
BSSID 32:59:05:91:a6:e2 blacklist count incremented to 2
wlan0: Blacklist count 2 --> request scan in 500 ms
wlan0: Ignore new scan request for 0.500000 sec since an earlier request is scheduled to trigger sooner
wlan0: WPA: Clear old PMK and PTK
wlan0: Disconnect event - remove keys
wlan0: State: COMPLETED -> DISCONNECTED
nl80211: Set wlan0 operstate 1->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
nl80211: Skip set_supp_port(unauthorized) while not associated
EAPOL: SUPP_BE entering state INITIALIZE
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
wlan0: State: DISCONNECTED -> DISCONNECTED
nl80211: Set wlan0 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wlan0: Ignore new scan request for 1.000000 sec since an earlier request is scheduled to trigger sooner
RTM_NEWLINK: ifi_index=3 ifname=wlan0 operstate=2 linkmode=1 ifi_family=0 ifi_flags=0x1003 ([UP])
wlan0: State: DISCONNECTED -> SCANNING
wlan0: Re-association to the same ESS
wlan0: Add radio work 'connect'@0x58c438
wlan0: First radio work item in the queue - schedule start immediately
wlan0: Starting radio work 'connect'@0x58c438 after 0.000049 second wait
wlan0: Trying to associate with SSID 'FooBar'
wlan0: Cancelling scan request
wlan0: WPA: clearing own WPA/RSN IE
wlan0: Automatic auth_alg selection: 0x1
wlan0: WPA: No WPA/RSN IE available from association info
wlan0: WPA: Set cipher suites based on configuration
wlan0: WPA: Selected cipher suites: group 16 pairwise 16 key_mgmt 2 proto 2
wlan0: WPA: clearing AP WPA IE
wlan0: WPA: clearing AP RSN IE
wlan0: WPA: using GTK CCMP
wlan0: WPA: using PTK CCMP
wlan0: WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
wlan0: State: SCANNING -> ASSOCIATING
nl80211: Set wlan0 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
IBSS already found in scan results, adjust control freq: 2462
nl80211: Join IBSS (ifindex=3)
nl80211: Set mode ifindex 3 iftype 1 (ADHOC)
nl80211: Unsubscribe mgmt frames handle 0x88df3ef1 (mode change)
nl80211: Subscribe to mgmt frames with non-AP handle 0x57b678
nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x57b678 match=
nl80211: Register frame command failed (type=176): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=06
nl80211: Register frame command failed (type=208): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=1): 06
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=0a07
nl80211: Register frame command failed (type=208): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=2): 0a 07
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=0a11
nl80211: Register frame command failed (type=208): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=2): 0a 11
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=1101
nl80211: Register frame command failed (type=208): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=2): 11 01
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=1102
nl80211: Register frame command failed (type=208): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=2): 11 02
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=0505
nl80211: Register frame command failed (type=208): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=2): 05 05
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x57b678 match=0500
nl80211: Register frame command failed (type=208): ret=-22 (Invalid argument)
nl80211: Register frame match - hexdump(len=2): 05 00
nl80211: Failed to register Action frame processing - ignore for now
  * SSID - hexdump_ascii(len=6):
     46 6f 6f 42 61 72                                 FooBar
  * freq=2462
  * vht_enabled=0
  * ht_enabled=0
  * channel_type=0
  * control port
  * Extra IEs for Beacon/Probe Response frames - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
nl80211: Join IBSS request sent successfully
wlan0: Setting authentication timeout: 60 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
RTM_NEWLINK: ifi_index=3 ifname=wlan0 wext ifi_family=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK: ifi_index=3 ifname=wlan0 operstate=5 linkmode=1 ifi_family=0 ifi_flags=0x11003 ([UP][LOWER_UP])
nl80211: Event message available
nl80211: Drv Event 43 (NL80211_CMD_JOIN_IBSS) received for wlan0
nl80211: IBSS 32:59:05:91:a6:e2 joined
nl80211: IBSS-joined on 2462 MHz
nl80211: Operating frequency for the associated BSS from scan results: 2462 MHz
nl80211: IBSS on frequency 2462 MHz
wlan0: Event ASSOC (0) received
wlan0: Association info event
wlan0: freq=2462 MHz
wlan0: State: ASSOCIATING -> ASSOCIATED
nl80211: Set wlan0 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
wlan0: Associated to a new BSS: BSSID=32:59:05:91:a6:e2
wlan0: Select network based on association information
wlan0: Network configuration found for the current AP
wlan0: WPA: Using WPA IE from AssocReq to set cipher suites
wlan0: WPA: Selected cipher suites: group 16 pairwise 16 key_mgmt 2 proto 2
wlan0: WPA: clearing AP WPA IE
wlan0: WPA: clearing AP RSN IE
wlan0: WPA: using GTK CCMP
wlan0: WPA: using PTK CCMP
wlan0: WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
wlan0: Associated with 32:59:05:91:a6:e2
wlan0: WPA: Association event - clear replay counter
wlan0: WPA: Clear old PTK
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
wlan0: Cancelling authentication timeout
Removed BSSID 32:59:05:91:a6:e2 from blacklist
wlan0: State: ASSOCIATED -> COMPLETED
wlan0: Radio work 'connect'@0x58c438 done in 0.499545 seconds
wlan0: radio_work_free('connect'@0x58c438: num_active_works --> 0
wlan0: CTRL-EVENT-CONNECTED - Connection to 32:59:05:91:a6:e2 completed [id=0 id_str=]
nl80211: Set wlan0 operstate 0->1 (UP)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
wlan0: Cancelling scan request
WMM AC: Missing IEs
wlan0: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
RTM_NEWLINK: ifi_index=3 ifname=wlan0 operstate=6 linkmode=1 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
RTM_NEWLINK: ifi_index=3 ifname=wlan0 operstate=6 linkmode=1 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
EAPOL: startWhen --> 0
EAPOL: disable timer tick
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: enable timer tick
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)


More information about the Hostap mailing list