Senao NL-2511CD+ doesn't work with WPA-EAP

[Ruzsinszky Attila]

> > I can't see traffic on eth1 or wifi0 (eth1 = wlan0).
>
> Is eth1 just renamed wlan0?
Yes. Now I modified a file somewhere  and I got back wlan0 again. :-)

> > Initializing interface 'wifi0' conf 'wpa_supplicant.conf' driver
> > 'wext' ctrl_interface 'N/A'
>
> wifi0 is incorrect interface to use here. You should use wlan0 (or
> whatever it is renamed to).
I know! But I made a try and the log was from this test.

> > With interface eth1 the situation is the same!
>
> Could you please send the debug log showing this?
Yes. Tomorrow I will make again.

> > hostap: module not supported by Novell, setting U taint flag.
> > hostap_cs: module not supported by Novell, setting U taint flag.
> > hostap_cs: 0.4.4-kernel (Jouni Malinen <jkmaline at cc.hut.fi>)
> > hostap_cs: setting Vcc=33 (constant)
> > hostap_cs: setting Vcc=33 (from config)
> > Checking CFTABLE_ENTRY 0x01 (default 0x01)
> > IO window settings: cfg->io.nwin=1 dflt.io.nwin=1
> > io->flags = 0x0046, io.base=0x0000, len=64
> > hostap_cs: Registered netdevice wifi0
> > hostap_cs: index 0x01: Vcc 3.3, irq 3, io 0x0100-0x013f
>
> Is this all output from Host AP driver? I would have expected to see
> more information here (e.g., firmware versions)..
Here it is: (with renamed hermes.ko)
...
kernel: pccard: PCMCIA card inserted into slot 0
kernel: cs: memory probe 0xa0000000-0xa0ffffff: clean.
kernel: pcmcia: registering new device pcmcia0.0
kernel: orinoco: Unknown symbol hermes_read_ltv
kernel: orinoco: Unknown symbol hermes_init
kernel: orinoco: Unknown symbol hermes_bap_pwrite
kernel: orinoco: Unknown symbol hermes_write_ltv
kernel: orinoco: Unknown symbol hermes_docmd_wait
kernel: orinoco: Unknown symbol hermes_allocate
kernel: orinoco: Unknown symbol hermes_bap_pwrite_pad
kernel: orinoco: Unknown symbol hermes_bap_pread
kernel: orinoco_cs: Unknown symbol free_orinocodev
kernel: orinoco_cs: Unknown symbol orinoco_reinit_firmware
kernel: orinoco_cs: Unknown symbol hermes_struct_init
kernel: orinoco_cs: Unknown symbol orinoco_interrupt
kernel: orinoco_cs: Unknown symbol __orinoco_up
kernel: orinoco_cs: Unknown symbol __orinoco_down
kernel: orinoco_cs: Unknown symbol alloc_orinocodev
kernel: ieee80211_crypt: module not supported by Novell, setting U taint flag.
kernel: ieee80211_crypt: registered algorithm 'NULL'
kernel: hostap: module not supported by Novell, setting U taint flag.
kernel: hostap_cs: module not supported by Novell, setting U taint flag.
kernel: hostap_cs: 0.4.4-kernel (Jouni Malinen <jkmaline at cc.hut.fi>)
kernel: hostap_cs: setting Vcc=33 (constant)
kernel: hostap_cs: setting Vcc=33 (from config)
kernel: Checking CFTABLE_ENTRY 0x01 (default 0x01)
kernel: IO window settings: cfg->io.nwin=1 dflt.io.nwin=1
kernel: io->flags = 0x0046, io.base=0x0000, len=64
kernel: hostap_cs: Registered netdevice wifi0
kernel: hostap_cs: index 0x01: Vcc 3.3, irq 3, io 0x0100-0x013f
kernel: prism2_hw_init: initialized in 196 ms
kernel: wifi0: NIC: id=0x800c v1.0.0
kernel: wifi0: PRI: id=0x15 v1.1.1
kernel: wifi0: STA: id=0x1f v1.8.4
kernel: wifi0: registered netdevice wlan0
kernel: pcmcia: Detected deprecated PCMCIA ioctl usage.
kernel: pcmcia: This interface will soon be removed from the kernel;
please expect breakage unless you upgrade to new tools.
kernel: pcmcia: see
http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for
details.
ifup: Service network not started and mode 'auto' -> skipping
ifup: Network interface is managed from NetworkManager
ifup: NetworkManager will be advised to set up wlan0
ifup: but it cannot be assured from here.
kernel: prism2: wlan0: operating mode changed 3 -> 2
kernel: wifi0: LinkStatus=2 (Disconnected)
kernel: wifi0: LinkStatus: BSSID=00:02:6f:xx:yy:zz
kernel: wifi0: LinkStatus=2 (Disconnected)
kernel: wifi0: LinkStatus: BSSID=44:44:44:44:44:44

TIA,
Ruzsi