Prism card not recognized

Wed Feb 7 13:22:25 PST 2007

On Tue, Feb 06, 2007, Pavel Roskin wrote:
> On Mon, 2007-02-05 at 21:44 +0100, Johan Bilien wrote:
> > Am I correct? Would adding something like:
> > 
> >  PCMCIA_DEVICE_MANF_CARD_PROD_ID1(0x0156, 0x0002, "AboveCable",
> >                                          0xfead109e),
> > 
> > solve the problem?
> 
> Yes, I think so.

Thanks,

so I did this and hostap gets loaded and the card gets listed as an eth0
and a wlan0_rename (udev quirks it seems).

Unfortunately wpa_supplicant won't authenticate to the network. It seems
to scan successfully, receive the EAP messages successfully, but seems
to stop the authentication process shortly after and start a new scan.
(log attached)

kernel log shows a worrying
localhost kernel: eth0: hfa384x_set_rid: CMDCODE_ACCESS_WRITE failed
(res=127, rid=fc48, len=2)

which has me wonder if the card actually has a PRISM2 chipset. It does
have the exact same ID as the Intersil and hostap seems to work
to some extent though.

Is there a way to be sure? Would the card not have a PRISM chipset, is
there any chance to get wpa_supplicant working? The network uses WEP
(not WPA) with 802.1X EAP/MSChap.

Best regards
-- 
Johan Bilien
<jobi at via.ecp.fr>
-------------- next part --------------
Initializing interface 'eth0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'hostap' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
Line: 4 - start of a new network block
ssid - hexdump_ascii(len=2):
     6c 75                                             lu              
key_mgmt: 0x8
eap methods - hexdump(len=16): 00 00 00 00 19 00 00 00 00 00 00 00 00 00 00 00
phase2 - hexdump_ascii(len=13):
     61 75 74 68 3d 4d 53 43 48 41 50 56 32            auth=MSCHAPV2   
identity - hexdump_ascii(len=6):
     79 61 77 32 30 36                                 yaw206          
password - hexdump_ascii(len=9): [REMOVED]
Priority group 0
   id=0 ssid='lu'
Initializing interface (2) 'eth0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=20 WE(source)=18 enc_capa=0xf
  capabilities: key_mgmt 0xf enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:02:6f:03:7c:39
wpa_driver_hostap_set_wpa: enabled=1
Driver does not support WPA.
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_countermeasures: enabled=0
wpa_driver_hostap_set_drop_unencrypted: enabled=1
Setting scan request: 0 sec 100000 usec
Added interface eth0
RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Trying to get current scan results first without requesting a new scan to speed up initial association
Received 878 bytes of scan results (6 BSSes)
Scan results: 6
Selecting BSS from priority group 0
0: 00:0d:bd:da:b9:4e ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
1: 00:0d:bd:da:b9:b9 ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
2: 00:12:d9:a7:a6:40 ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
3: 00:0d:bd:da:b9:8e ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
4: 00:0d:bd:da:b9:cf ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
5: 00:0d:bc:25:fa:df ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
   selected non-WPA AP 00:0d:bd:da:b9:4e ssid='lu'
Trying to associate with 00:0d:bd:da:b9:4e (SSID='lu' freq=2412 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: clearing AP WPA IE
WPA: clearing AP RSN IE
WPA: clearing own WPA/RSN IE
No keys have been configured - skip key clearing
wpa_driver_hostap_set_drop_unencrypted: enabled=1
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_hostap_associate
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - portControl=Auto
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b04 len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b1a len=11
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:0d:bd:da:b9:4e
State: ASSOCIATING -> ASSOCIATED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
Associated to a new BSS: BSSID=00:0d:bd:da:b9:4e
No keys have been configured - skip key clearing
Associated with 00:0d:bd:da:b9:4e
WPA: Association event - clear replay counter
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
Cancelling scan request
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
EAPOL: startWhen --> 0
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
TX EAPOL - hexdump(len=4): 01 01 00 00
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b19 len=8
Received 1256 bytes of scan results (8 BSSes)
Scan results: 8
Selecting BSS from priority group 0
0: 00:0d:bd:da:b9:4e ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
1: 00:0d:bd:da:b9:8e ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
2: 00:12:d9:a7:a6:40 ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
3: 00:0d:bd:da:b9:b9 ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
4: 00:14:a8:5f:48:a0 ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
5: 00:13:19:f2:24:90 ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
6: 00:0d:bc:25:fa:df ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
7: 00:13:19:f2:28:60 ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x1
   skip - no WPA/RSN IE
   selected non-WPA AP 00:0d:bd:da:b9:4e ssid='lu'
Already associated with the selected AP.
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
Setting scan request: 0 sec 100000 usec
Added BSSID 00:0d:bd:da:b9:4e into blacklist
CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
State: ASSOCIATED -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
Ignore event for foreign ifindex 12
Ignore event for foreign ifindex 12
Ignore event for foreign ifindex 12
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:0d:bd:da:b9:8e
State: DISCONNECTED -> ASSOCIATED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
Associated to a new BSS: BSSID=00:0d:bd:da:b9:8e
No keys have been configured - skip key clearing
Associated with 00:0d:bd:da:b9:8e
WPA: Association event - clear replay counter
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
Cancelling scan request
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
Setting scan request: 0 sec 100000 usec
Added BSSID 00:0d:bd:da:b9:8e into blacklist
CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
State: ASSOCIATED -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
Ignore event for foreign ifindex 12
Ignore event for foreign ifindex 12
Ignore event for foreign ifindex 12
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b19 len=8
Received 423 bytes of scan results (3 BSSes)
Scan results: 3
Selecting BSS from priority group 0
0: 00:0d:bd:da:b9:8e ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
1: 00:0d:bd:da:b9:b9 ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
2: 00:0d:bd:da:b9:cf ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
   selected non-WPA AP 00:0d:bd:da:b9:8e ssid='lu'
Trying to associate with 00:0d:bd:da:b9:8e (SSID='lu' freq=2437 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: clearing AP WPA IE
WPA: clearing AP RSN IE
WPA: clearing own WPA/RSN IE
No keys have been configured - skip key clearing
wpa_driver_hostap_set_drop_unencrypted: enabled=1
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_hostap_associate
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - portControl=Auto
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b04 len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b1a len=11
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:0d:bd:da:b9:8e
State: ASSOCIATING -> ASSOCIATED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
Associated to a new BSS: BSSID=00:0d:bd:da:b9:8e
No keys have been configured - skip key clearing
Associated with 00:0d:bd:da:b9:8e
WPA: Association event - clear replay counter
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
Cancelling scan request
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
EAPOL: startWhen --> 0
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
TX EAPOL - hexdump(len=4): 01 01 00 00
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b19 len=8
Received 942 bytes of scan results (6 BSSes)
Scan results: 6
Selecting BSS from priority group 0
0: 00:0d:bd:da:b9:4e ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
1: 00:0d:bd:da:b9:8e ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
2: 00:0d:bd:da:b9:b9 ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
3: 00:13:19:f2:24:90 ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
4: 00:13:19:f2:26:70 ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
5: 00:13:19:f2:28:60 ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x1
   skip - no WPA/RSN IE
   selected non-WPA AP 00:0d:bd:da:b9:4e ssid='lu'
Trying to associate with 00:0d:bd:da:b9:4e (SSID='lu' freq=2412 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: clearing AP WPA IE
WPA: clearing AP RSN IE
WPA: clearing own WPA/RSN IE
No keys have been configured - skip key clearing
wpa_driver_hostap_set_drop_unencrypted: enabled=1
State: ASSOCIATED -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_hostap_associate
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - portControl=Auto
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
BSSID 00:0d:bd:da:b9:4e blacklist count incremented to 2
CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
State: ASSOCIATING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b04 len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b1a len=11
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:0d:bd:da:b9:4e
State: DISCONNECTED -> ASSOCIATED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
Associated to a new BSS: BSSID=00:0d:bd:da:b9:4e
No keys have been configured - skip key clearing
Associated with 00:0d:bd:da:b9:4e
WPA: Association event - clear replay counter
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
Cancelling scan request
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
Setting scan request: 0 sec 100000 usec
BSSID 00:0d:bd:da:b9:4e blacklist count incremented to 3
CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
State: ASSOCIATED -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
Ignore event for foreign ifindex 12
Ignore event for foreign ifindex 12
Ignore event for foreign ifindex 12
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b19 len=8
Received 737 bytes of scan results (5 BSSes)
Scan results: 5
Selecting BSS from priority group 0
0: 00:0d:bd:da:b9:8e ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
1: 00:0d:bd:da:b9:b9 ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
2: 00:0d:bd:da:b9:cf ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
3: 00:13:19:f2:26:70 ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
4: 00:0d:bd:af:d2:3a ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
   selected non-WPA AP 00:0d:bd:da:b9:8e ssid='lu'
Trying to associate with 00:0d:bd:da:b9:8e (SSID='lu' freq=2437 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: clearing AP WPA IE
WPA: clearing AP RSN IE
WPA: clearing own WPA/RSN IE
No keys have been configured - skip key clearing
wpa_driver_hostap_set_drop_unencrypted: enabled=1
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_hostap_associate
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - portControl=Auto
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b04 len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b1a len=11
EAPOL: startWhen --> 0
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:0d:bd:da:b9:8e
State: ASSOCIATING -> ASSOCIATED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
Associated to a new BSS: BSSID=00:0d:bd:da:b9:8e
No keys have been configured - skip key clearing
Associated with 00:0d:bd:da:b9:8e
WPA: Association event - clear replay counter
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
Cancelling scan request
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b19 len=8
Received 737 bytes of scan results (5 BSSes)
Scan results: 5
Selecting BSS from priority group 0
0: 00:0d:bd:da:b9:4e ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - blacklisted
1: 00:0d:bd:da:b9:8e ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
2: 00:0d:bc:25:fa:df ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
3: 00:0d:bd:da:b9:cf ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
4: 00:13:19:f2:28:60 ssid='lu' wpa_ie_len=0 rsn_ie_len=0 caps=0x1
   skip - no WPA/RSN IE
   selected non-WPA AP 00:0d:bd:da:b9:8e ssid='lu'
Already associated with the selected AP.
EAPOL: startWhen --> 0
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
TX EAPOL - hexdump(len=4): 01 01 00 00
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
Setting scan request: 0 sec 100000 usec
BSSID 00:0d:bd:da:b9:8e blacklist count incremented to 2
CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
State: ASSOCIATED -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
Ignore event for foreign ifindex 12
Ignore event for foreign ifindex 12
Ignore event for foreign ifindex 12
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:0d:bc:25:fa:df
State: DISCONNECTED -> ASSOCIATED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
Associated to a new BSS: BSSID=00:0d:bc:25:fa:df
No keys have been configured - skip key clearing
Associated with 00:0d:bc:25:fa:df
WPA: Association event - clear replay counter
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
Cancelling scan request
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
EAPOL: startWhen --> 0
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
TX EAPOL - hexdump(len=4): 01 01 00 00
CTRL-EVENT-TERMINATING - signal 2 received
Removing interface eth0
State: ASSOCIATED -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_hostap_deauthenticate
wpa_driver_hostap_reset: type=2
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
wpa_driver_hostap_set_wpa: enabled=0
Failed to disable WPA in the driver.
wpa_driver_hostap_set_drop_unencrypted: enabled=0
wpa_driver_hostap_set_countermeasures: enabled=0
No keys have been configured - skip key clearing
WEXT: Operstate: linkmode=0, operstate=6
Removed BSSID 00:0d:bd:da:b9:8e from blacklist (clear)
Removed BSSID 00:0d:bd:da:b9:4e from blacklist (clear)
Cancelling scan request