Unable to connect to AP via WPA-PKS/CCMP
Thomas Heinz
thomasheinz
Thu Sep 29 08:14:09 PDT 2005
Hi
I am using hostap-driver 0.4.4 and wpa_supplicant 0.4.4 (Gentoo) to connect
via WPA-PSK to an access point. Recently, I updated the firmware of my
wireless pcmcia card to v1.1.1 (primary) and v1.8.4 (secondary). The
output of `hostap_diag -a wlan0` is contained in the attached file
"hostap_diag.wlan0". My wpa_supplicant.conf is also attached to this
e-mail.
When I run
# wpa_supplicant -ddd -c /etc/wpa_supplicant.conf -i wlan0
the following error/warning is printed:
ioctl[SIOCSIWPMKSA]: Operation not supported
The attached "kernel.log" is a dump of the kernel messages printed during
this procedure. Note that the kernel module hostap_crypt_ccmp is not
loaded. Loading it manually, does not help. Maybe it would have been
loaded at a later stage, if the connection was successful.
How would you approach this problem?
Is it a potential firmware issue?
Is it caused by the unsupported ioctl?
Thank you very much for your help.
Regards,
Thomas
-------------- next part --------------
Host AP driver diagnostics information for 'wlan0'
NICID: id=0x801b v1.0.0 (PRISM III PCMCIA (SST parallel flash))
PRIID: id=0x0015 v1.1.1
STAID: id=0x001f v1.8.4 (station firmware)
Known RIDs (Resource IDentifiers)
FC00=CNFPORTTYPE=1
FC01=CNFOWNMACADDR=00:01:36:07:68:3f
FC02=CNFDESIREDSSID=Lothlorien
FC03=CNFOWNCHANNEL=1
FC04=CNFOWNSSID=Lothlorien
FC05=CNFOWNATIMWINDOW=0
FC06=CNFSYSTEMSCALE=1
FC07=CNFMAXDATALEN=2304
FC08=CNFWDSADDRESS=00:00:00:00:00:00
FC09=CNFPMENABLED=0
FC0A=CNFPMEPS=1
FC0B=CNFMULTICASTRECEIVE=1
FC0C=CNFMAXSLEEPDURATION=1000
FC0D=CNFPMHOLDOVERDURATION=100
FC0E=CNFOWNNAME=
FC10=CNFOWNDTIMPERIOD=1
FC20=UNKNOWN1=289
FC21=UNKNOWN2=289
FC23=CNFWEPDEFAULTKEYID=0
FC28=CNFWEPFLAGS=<01><00>
FC2A=CNFAUTHENTICATION=1
FC2C=CNFTXCONTROL=512
FC2D=CNFROAMINGMODE=3
FC30=CNFRCVCRCERROR=0
FC31=CNFMMLIFE=65000
FC32=CNFALTRETRYCOUNT=7
FC33=CNFBEACONINT=100
FC35=CNFSTAPCFINFO=<01><00>
FC40=CNFTIMCTRL=0
FC41=UNKNOWN3=<00><00><00><00><00><00>
FC42=CNFTHIRTY2TALLY=1
FC43=CNFENHSECURITY=0
FC46=CNFDBMADJUST=100
FC49=PROPAGATIONDELAY=0
FC80=GROUPADDRESSES=
FC81=CREATEIBSS=1
FC82=FRAGMENTATIONTHRESHOLD=65534
FC83=RTSTHRESHOLD=2347
FC84=TXRATECONTROL=15
FC85=PROMISCUOUSMODE=0
FCB0=CNFSHORTPREAMBLE=0
FCB3=CNFBASICRATES=<03><00>
FCB4=CNFSUPPORTEDRATES=<0f><00>
FCB5=CNFFALLBACKCTRL=1148
FCB6=WEPKEYDISABLE=0
FCBA=CNFPASSIVESCANCTRL=0
FCBB=SSNHANDLINGMODE=1
FCBC=MDCCONTROL=0
FCBD=MDCCOUNTRY=<20><20><20><00>
FCBE=TXPOWERMAX=18
FCBF=CNFLFOENABLED=0
FCC0=CAPINFO=17
FCC1=LISTENINTERVAL=10
FCC2=SW_ANT_DIV=<03><00><02><00><02><00>
FCC4=LED_CTRL=<40><00><40><00><06><00><80><00><06><00>
FCC5=HFODELAY=3
FCC6=DISALLOWEDBSSID=<00><00><00><00><00><00>
FCE0=TICKTIME=2000
FCE1=SCANREQUEST=<ff><3f><20><00>
FCE2=JOINREQUEST=<21><01><27><0e><40><0e><1c><0f>
FCE5=HOSTSCAN=<ff><1f><00><0a><00><00><00><00><00><00><00><00><00><00><00><00><00><00><00><00><00><00><00><00><00><00><00><00><00><00><00><00><00><00><00><00><00><00>
FD00=MAXLOADTIME=60000
FD01=DOWNLOADBUFFER=<60><00><00><00><00><10>
FD02=PRIID=0x15 v1.1.1
FD03=PRISUPRANGE=0 0x03 1 4-4
FD04=CFIACTRANGES=1 0x02 2 1-1
FD0A=NICSERNUM=SA01000000<00><00>
FD0B=NICID=0x801b v1.0.0
FD0C=MFISUPRANGE=0 0x01 1 1-1
FD0D=CFISUPRANGE=0 0x02 2 1-1
FD10=CHANNELLIST=<ff><1f>
FD11=REGULATORYDOMAINS=0
FD12=TEMPTYPE=1
FD13=CIS=<01><03><00><00><ff><17><04><67><5a><08><ff><1d><05><03><67><5a><08><ff><15><1f><01><00><50><43><4d><43><49><41><00><31><31><4d><20><57><4c><41><4e><20><43><61><72><64><20><76><33><2e><30><00><00><00><ff><20><04><74><02><13><16><21><02><06><00><22><02><01><07><22><05><02><40><42><0f><00><22><05><02><80><84><1e><00><22><05><02><60><ec><53><00><22><05><02><c0><d8><a7><00><22><02><03><07><22><08><04><06><00><01><36><07><68><3f><22><02><05><01><1a><07><03><01><e0><03><00><00><01><1b><0e><c1><01><19><76><35><d5><19><36><36><05><46><ff><ff><ff><ff><ff><02><03><07><22><08><04><06><00><06><25><2b><9f><a5><22><02><05><01><1a><07><03><01><e0><03><00><00><01><1b><0e><c1><01><19><76><35><d5><19><36><36><05><46><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><ff><36><00><34><00><00> + 222*<ff>
FD20=STAID=0x1f v1.8.4
FD21=STASUPRANGE=0 0x04 1 1-15
FD22=MFIACTRANGES=1 0x01 1 1-1
FD23=CFIACTRANGES2=1 0x02 2 1-1
FD24=PRODUCTNAME=ISL37100P
FD40=PORTSTATUS=4
FD41=CURRENTSSID=Lothlorien
FD42=CURRENTBSSID=00:12:17:b3:27:aa
FD43=COMMSQUALITY=<00><00><29><00><ff><00>
FD44=CURRENTTXRATE=8
FD45=CURRENTBEACONINTERVAL=31508
FD46=CURRENTSCALETHRESHOLDS=<36><00><36><00><36><00><04><00><01><00><03><00>
FD47=PROTOCOLRSPTIME=100
FD48=SHORTRETRYLIMIT=8
FD49=LONGRETRYLIMIT=5
FD4A=MAXTRANSMITLIFETIME=512
FD4B=MAXRECEIVELIFETIME=512
FD4C=CFPOLLABLE=0
FD4D=AUTHENTICATIONALGORITHMS=<01><00><01><00>
FD4F=PRIVACYOPTIONIMPLEMENTED=1
FD51=DBMCOMMSQUALITY=<00><00><a9><ff><9b><00>
FD88=SCANRESULTSTABLE=<00><00><03><00><00><00><ff><df><0d><e6><00><12><17><b3><27><aa><14><7b><01><00><0a><00><4c><6f><74><68><6c><6f><72><69><65><6e><d7><60><bc><15><8c><c8><73><01><7a><46><b0><9d><3b><30><fa><4e><7b><3b><d9><cb><e2><96><c7><60><12><e2><04><66><af><e4><90><3b><03><d0>
FD89=HOSTSCANRESULTS=<40><00><03><00>
FD8A=AUTHENTICATIONUSED=<00><00>
FD8B=CNFFAASWITCHCTRL=1
FD8D=ASSOCIATIONFAILURE=<00><12><17><b3><27><aa><02><00>
FDC0=PHYTYPE=2
FDC1=CURRENTCHANNEL=0
FDC2=CURRENTPOWERSTATE=1
FDC3=CCAMODE=2
FDC6=SUPPORTEDDATARATES=<02><04><0b><16>
FDC7=LFO_VOLT_REG_TEST_RES=<00><00><00><00><00><00>
FFFE=BUILDSEQ=<00><00><00><00>
FFFF=FWID=010101.hex.<00>sf010804.hex<00><00>ri
Unknown RIDs (Resource IDentifiers)
Baseband proccessor (BBP) Configuration Registers
CR0 (Part/Version Code): 116 - Part=7 (HFA3871 series?) Version=4 (3871 Version?)
CR1 (I/O Polarity): 192 (normal setting 0)
Phase of RX carrier rotation sense: Inverted rotation (CW), Invert Q in
Phase of TX carrier rotation sense: Inverted rotation (CW), Invert Q out
Phase of TX output clock (TXCLK) pin: NON-Inverted TXCLK
Active level of the Transmit Ready output: TX_RDY Active 1
Active level of the transmit enable input: TX_PE Active 1
Active level of the Clear Channel Assessment output: CCA Active 0
Active level of the MD_RDY output: MD_RDY Active 1
Phase of the RX_CLK output: Non-Inverted Clk
CR2 (I Cover Code): 0 (nominally 72)
CR3 (Q Cover Code): 56 (nominally 72)
CR4 (TX Preamble Length): 128 (IEEE 802.11: 128)
CR5 (TX Signal Field): 3
Preamble mode: Normal
TX data rate: 11 = CCK - 8 chip sequence (11Mbps)
CR6 (TX Service Field): 4
CR7 (TX Length Field, High): 0
CR8 (TX Length Field, Low): 116
TX Length Field: 116 usec
CR9 (TX Configure): 32
CCA sample mode time: 19.9 usec
CCA mode: CCA is based on (CS1 OR SQ1/CS2)
TX test modes: Alternating bits for carrier suppression test
Enable TX test modes: normal operation
Antenna choice for TX: Set AntSel low
TX Antenna Mode: set AntSel pin to value in choice above
CR10 (RX Configure): 202
Initial CS2 estimate: Use SQ1 from Barker correlator peaks
CIR estimate/Dot product clock control: only on after detect
SFD Time-out values: 56 usec
MD_RDY control: After SFD
Force Frequency Offset Estimating in all antenna diversity timelines: disabled
Antenna choice for RX when single antenna acquisition is selected: AntSel pin high
Antenna acquire: dual antenna for diversity acquisition
CR11 (RX/TX Configure): 3
Continuous internal RX 22 and 44 MHZ clocks: 0
A/D input coupling: DC
TX filter / CMF weight select: US
Ping Pong Differential Encode: disabled
CCA mode: normal CCA; CCA will immediately respond to changes in ED, CS1, and SQ1
Precursor value in CIR estimate: 3
CR12 (A/D Test Modes 1): 0
All DAC and A/D clock source control: normal internal clocks
TX DAC clock: enable
RX DAC clock: enable
I DAC clock: enable
Q DAC clock: enable
RF A/D clock: enable
I A/D clock: enable
Q A/D clock: enable
CR13 (A/D Test Modes 2): 0
Standby: disable
SLEEP TX: disable
SLEEP RX: disable
SLEEP IQ: disable
Analog TX Shut_down: disable
Analog RX Shut_down: disable
Analog Standby: disable
Manual control of mixed signal power down signals (other CR13 bits): disable
CR14 (A/D Test Modes 3): 0
DFS - select straight binary output of I/Q and RF A/D converters: 0
I/Q DAC input control: normal (TX filter)
Enable test bus into RX and TX DAC: disable
Enable RF A/D into RX DAC: disable
VRbit1: 0
VRbit0: 0
CR15 (AGC GainClip): 66
CR16 (AGC Sat Cpints): 207
AGC mid Sat counts: 12
AGC low Sat counts: 15
CR17 (AGC Update Control): 158
AGC update during CIR injest: enable
AGC timer count: 30 (must be >31)
CR18 (AGC HiSat): 250
CR19 (AGC LockinLevel/CW detect threshold): 247
CR20 (AGC LockWindow, pos side): 200
CR21 (AGC Threshold): 24
CR22 (AGC Lookup Table Addr and Control): 123
CR23 (AGC Lookup Table Data): 32
CR24 (AGC LoopGain): 9
CR25 (AGC RX_IF): 32
CR26 (AGC Test Modes): 130
CR27 (AGC RX_RF Threshold): 24
CR28 (AGC Low SatAtten): 20
CR29 (AGC LockWindow, negative side): 202
CR30 (Carrier Sense 2): 45
CR31 (Manual TX Power Control): 182
CR32 (Test Modes 1): 0
CR33 (Test Modes 2): 0
CR34 (Test Bus Address): 0
CR35 (CMF Coefficient Control): 32
CR36 (Scrambler Seed, Long Preamble Option): 139
CR37 (Scrambler Seed, Short Preamble Option): 15
CR38 (ED Threshold): 6
CR39 (CMF Gain Threshold): 10
CR40 (Threshold for antenna decision): 4
CR41 (Preamble tracking loop lead coefficient): 0
CR42 (Preamble tracking loop lag coefficient): 0
CR43 (Header tracking loop lead coefficient): 158
CR44 (Header tracking loop lag coefficient): 36
CR45 (Data tracking loop lead coefficient): 32
CR46 (Data tracking loop lag coefficient): 40
CR47 (RF attenuator value): 158
CR48 (ED and SQ1 control and SQ1 scale factor): 38
CR49 (Read only register mux control for registers 50 to 63): 219
CW RSSI threshold: 91
CR50..CR63: 'a' value
CR50 (Test Bus Read): 0
CR51 (Noise floorAntA): 15
CR52 (Noise floorAntB): 13
CR53 (AGC error / I DC Offset): 4
CR54 (Unassigned / Q DC Offset): 0
CR55 (Unassigned Multipath Metric): 0
CR56 (Unassigned / Multipath Count): 1
CR57 (Unassigned / Packet Signal Quality): 20
CR58 (TX Power Measurement): -9
CR59 (RX Mean Power / Header Signal Quality): 13
CR60 (RX_IF AGC): 111
CR61 (RX Status Reg): 13
TX PWR det Register semaphore (CR58 updated since last read)
AGC_lock (AGC is within limits of lock window CR20)
RX_RF_AGC - status of AGC output to RF chip
CR62 (RSSI): 73
CR63 (RX Status Reg): 2
Signal field value: 1 M
Antenna selected by received when last valid header CRC occurred
Production Data Area (PDA)
PDR 0x0001 len=16 Platform name / Manufacturing part number
49 53 4c 33 37 31 30 30 50 00 00 00 00 00 00 00
PDR 0x0002 len=2 PDA Version Record
01 00
PDR 0x0006 len=10 RF Modem Supplier Range
00 00 01 00 01 00 01 00 01 00
PDR 0x0007 len=10 MAC Controller Supplier Range
00 00 02 00 02 00 01 00 01 00
PDR 0x0008 len=8 NIC ID (component ID)
1b 80 00 00 01 00 00 00
PDR 0x0101 len=6 MAC Address
00 01 36 07 68 3f
PDR 0x0103 len=12 Regulatory Domain List
01 00 30 00 00 00 00 00 00 00 00 00
PDR 0x0104 len=2 Allowed Channel Set/Active Channel List
ff 1f
PDR 0x0105 len=2 Default Channel
03 00
PDR 0x0107 len=2 Temperature Type
01 00
PDR 0x0202 len=100 3861 Baseline Register Settings
c0 02 01 04 38 06 80 08 03 0a 04 0c 01 0e 09 10 20 12 ca 14 03 16 00 18 00 1a 00 1c 42 1e cf 20 9e 22 fa 24 f7 26 c8 28 18 2a 7b 2c 20 2e 09 30 20 32 82 34 18 36 14 38 ca 3a 2d 3c e7 3e 00 40 00 42 00 44 20 46 8b 48 0f 4a 06 4c 0a 4e 04 50 00 52 00 54 9e 56 24 58 20 5a 28 5c 9e 5e 26 60 db 62 00 04
PDR 0x0203 len=128 3861 Shadow Register Settings
00 2c 0c 2e 01 2c 10 2e 02 2c 14 2e 03 2c 18 2e 04 2c 1c 2e 05 2c 20 2e 06 2c 24 2e 07 2c 28 2e 08 2c 2e 2e 09 2c 34 2e 0a 2c 38 2e 0b 2c 3c 2e 0c 2c 3f 2e 0d 2c 43 2e 0e 2c 46 2e 0f 2c 48 2e 10 2c 4b 2e 11 2c 50 2e 12 2c 55 2e 13 2c 5a 2e 14 2c 63 2e 15 2c 6d 2e 16 2c 76 2e 17 2c 7f 2e 18 2c 7f 2e 19 2c 7f 2e 1a 2c 7f 2e 1b 2c 7f 2e 1c 2c 7f 2e 1d 2c 7f 2e 1e 2c 7f 2e 7b 2c 20 2e
PDR 0x0204 len=80 3861 IF/RF Register Settings
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50 0b 00 00 00 63 09 00 20 64 09 00 60 65 09 00 a0 66 09 00 e0 80 09 00 20 81 09 00 60 82 09 00 a0 83 09 00 e0 85 09 00 20 86 09 00 60 87 09 00 a0 a0 09 00 e0 a2 09 00 20 a5 09 00 20
PDR 0x0300 len=28 3861 Channel Calibration Set Point
f5 00 f6 00 f6 00 f5 00 f7 00 f5 00 f4 00 f2 00 f0 00 ee 00 ec 00 e9 00 e9 00 e5 00
PDR 0x0301 len=34 3861 Channel Calibration Integrator
c2 00 c0 00 bf 00 be 00 bc 00 bb 00 ba 00 b9 00 b8 00 b6 00 b5 00 b4 00 b3 00 b0 00 98 00 80 00 50 00
PDR 0x0400 len=2 3842 PRISM II NIC Configuration
03 00
PDR 0x0405 len=4 ZIF Synthesizer Settings
26 00 00 70
PDR 0x0900 len=60 3861 Manufacturing Test Channel Set Points
f5 00 f6 00 f6 00 f5 00 f7 00 f5 00 f4 00 f2 00 f0 00 ee 00 ec 00 e9 00 e9 00 e5 00 f5 00 e9 00 f5 00 f6 00 f6 00 f5 00 f7 00 f5 00 f4 00 f2 00 f0 00 ee 00 ec 00 e9 00 e9 00 e5 00
PDR 0x0901 len=66 Manufacturing Test Channel Integrators
c2 00 c0 00 bf 00 be 00 bc 00 bb 00 ba 00 b9 00 b8 00 b6 00 b5 00 b4 00 b3 00 b0 00 c2 00 b3 00 c2 00 c0 00 bf 00 be 00 bc 00 bb 00 ba 00 b9 00 b8 00 b6 00 b5 00 b4 00 b3 00 b0 00 98 00 80 00 50 00
PDR 0x0000 len=2 PDA End Record
71 f0
-------------- next part --------------
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=0
eapol_version=1
ap_scan=1
fast_reauth=1
opensc_engine_path=/usr/lib/opensc/engine_opensc.so
pkcs11_engine_path=/usr/lib/opensc/engine_pkcs11.so
pkcs11_module_path=/usr/lib/pkcs11/opensc-pkcs11.so
network={
ssid="somessid"
priority=0
scan_ssid=1
proto=WPA
key_mgmt=WPA-PSK
pairwise=CCMP
group=CCMP
psk=<somepsk>
}
-------------- next part --------------
A non-text attachment was scrubbed...
Name: kernel.log
Type: text/x-log
Size: 4873 bytes
Desc: not available
Url : http://lists.shmoo.com/pipermail/hostap/attachments/20050929/c6458c4c/attachment.bin
More information about the Hostap
mailing list