wpa_supplicant and ipw2100
Tony Houghton
h
Fri Sep 23 09:51:09 PDT 2005
I'm trying to get wpa_supplicant working with the ipw2100 in my Centrino
laptop. I used wpa_supplicant 0.3.9; ieee80211 1.0.3; ipw2100 1.1.2
plus the patch to make it compile with the new ieee80211 driver; and
version 1.3 of the firmware. I've attached my compile-time and run-time
config files, minus comments for brevity.
But whatever I try, wpa_supplicant just reports:
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
along with other stuff, but I think that's the significant problem.
AFAICT ipw2100 has a long history of not working properly with
wpa_supplicant. I also tried wpa_supplicant 0.2.7 and 0.4.4, with
similar results.
Next I tried ndiswrapper (1.3rc1). Without WPA that does work, but only
if I load and unload the ipw2100 driver first! But if I do try to use
WPA that fails too. I've attached the output of wpa_supplicant -d. There
are three files, because I tried all 3 possible values of ap_scan. With
values 1 and 2 the messages kept repeating the cycle after
EAPOL: SUPP_PAE entering state DISCONNECTED
Next I tried ndiswrapper again but with a cheap TI-based PC card. That
time wpa_supplicant did work successfully, so I think that vindicates
the way I've tried to set it up.
--
TH * http://www.realh.co.uk
-------------- next part --------------
CONFIG_DRIVER_HOSTAP=n
CONFIG_DRIVER_PRISM54=n
CONFIG_DRIVER_NDISWRAPPER=y
CONFIG_DRIVER_ATMEL=n
CONFIG_DRIVER_IPW=y
CONFIG_DRIVER_WEXT=y
CONFIG_IEEE8021X_EAPOL=n
CONFIG_EAP_MD5=n
CONFIG_EAP_MSCHAPV2=n
CONFIG_EAP_TLS=n
CONFIG_EAP_PEAP=n
CONFIG_EAP_TTLS=n
CONFIG_EAP_GTC=n
CONFIG_EAP_OTP=n
CONFIG_EAP_LEAP=n
CONFIG_PKCS12=n
CONFIG_CTRL_IFACE=y
-------------- next part --------------
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=0
eapol_version=1
ap_scan=1
fast_reauth=1
network={
ssid="Sirius"
psk="<Deleted>"
key_mgmt=WPA-PSK
priority=5
proto=WPA
pairwise=TKIP
}
-------------- next part --------------
Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 'ndiswrapper'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group=0
eapol_version=1
ap_scan=0
fast_reauth=1
Line 268: removed CCMP from group cipher list since it was not allowed for pairwise cipher
Priority group 5
id=0 ssid='Sirius'
Initializing interface (2) 'wlan0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Own MAC address: 00:04:23:80:03:78
Setting scan request: 0 sec 100000 usec
Wireless event: cmd=0x8b06 len=8
Signal 2 received - terminating
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
No keys have been configured - skip key clearing
-------------- next part --------------
Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 'ndiswrapper'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group=0
eapol_version=1
ap_scan=1
fast_reauth=1
Line 268: removed CCMP from group cipher list since it was not allowed for pairwise cipher
Priority group 5
id=0 ssid='Sirius'
Initializing interface (2) 'wlan0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Own MAC address: 00:04:23:80:03:78
Setting scan request: 0 sec 100000 usec
Wireless event: cmd=0x8b06 len=8
Starting AP scan (broadcast SSID)
Scan timeout - try to get results
Received 274 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 5
0: 00:11:50:06:13:7d ssid='Sirius' wpa_ie_len=24 rsn_ie_len=0
selected
Trying to associate with 00:11:50:06:13:7d (SSID='Sirius' freq=2437 MHz)
Cancelling scan request
Automatic auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Own WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8c07 len=52
Wireless event: cmd=0x8c08 len=35
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
Added BSSID 00:00:00:00:00:00 into blacklist
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
Disconnect event - remove keys
RX EAPOL from 00:11:50:06:13:7d
Setting authentication timeout: 10 sec 0 usec
EAPOL: Ignoring WPA EAPOL-Key frame in EAPOL state machines
IEEE 802.1X RX: version=1 type=3 length=95
EAPOL-Key type=254
WPA: RX message 1 of 4-Way Handshake from 00:11:50:06:13:7d (ver=1)
WPA: Renewed SNonce - hexdump(len=32): 27 ee 8c 0c d7 5d 1e 5c f6 19 67 98 03 78 e0 b1 8f ca e5 0a 81 e7 0e 87 81 d6 ab 73 3c 56 cb ac
WPA: PMK - hexdump(len=32): [REMOVED]
WPA: PTK - hexdump(len=64): [REMOVED]
WPA: EAPOL-Key MIC - hexdump(len=16): 0d 10 f4 af 4c 7e 64 f9 bf cd 80 e2 43 89 f1 10
WPA: Sending EAPOL-Key 2/4
Wireless event: cmd=0x8c07 len=52
Wireless event: cmd=0x8c08 len=35
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:11:50:06:13:7d
Association event - clear replay counter
Associated to a new BSS: BSSID=00:11:50:06:13:7d
No keys have been configured - skip key clearing
Associated with 00:11:50:06:13:7d
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
RX EAPOL from 00:11:50:06:13:7d
Setting authentication timeout: 10 sec 0 usec
EAPOL: Ignoring WPA EAPOL-Key frame in EAPOL state machines
IEEE 802.1X RX: version=1 type=3 length=95
EAPOL-Key type=254
WPA: RX message 1 of 4-Way Handshake from 00:11:50:06:13:7d (ver=1)
WPA: Renewed SNonce - hexdump(len=32): 37 6d 3a 14 ab 4c 71 06 82 03 82 74 ea 1b d6 82 e8 f8 9c d0 1d 54 38 5f 93 c0 25 7a 82 d0 26 ac
WPA: PMK - hexdump(len=32): [REMOVED]
WPA: PTK - hexdump(len=64): [REMOVED]
WPA: EAPOL-Key MIC - hexdump(len=16): d6 87 17 2a 94 aa db 07 98 18 9d 00 36 06 2f 41
WPA: Sending EAPOL-Key 2/4
Wireless event: cmd=0x8c07 len=52
Wireless event: cmd=0x8c08 len=35
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:11:50:06:13:7d
Association event - clear replay counter
Associated with 00:11:50:06:13:7d
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
RX EAPOL from 00:11:50:06:13:7d
Setting authentication timeout: 10 sec 0 usec
EAPOL: Ignoring WPA EAPOL-Key frame in EAPOL state machines
IEEE 802.1X RX: version=1 type=3 length=95
EAPOL-Key type=254
WPA: RX message 1 of 4-Way Handshake from 00:11:50:06:13:7d (ver=1)
WPA: Renewed SNonce - hexdump(len=32): cc 33 36 56 1e d7 c2 25 3a b8 4d 7a de 64 99 bd 1b 1d b5 49 61 e1 5b f7 d0 48 44 60 9f 48 02 96
WPA: PMK - hexdump(len=32): [REMOVED]
WPA: PTK - hexdump(len=64): [REMOVED]
WPA: EAPOL-Key MIC - hexdump(len=16): 47 a4 45 50 96 1a 48 de 97 36 02 e5 62 77 4e f9
WPA: Sending EAPOL-Key 2/4
Wireless event: cmd=0x8c07 len=52
Wireless event: cmd=0x8c08 len=35
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:11:50:06:13:7d
Association event - clear replay counter
Associated with 00:11:50:06:13:7d
EAPOL: External notification - portEnabled=0
-------------- next part --------------
Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 'ndiswrapper'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group=0
eapol_version=1
ap_scan=2
fast_reauth=1
Line 268: removed CCMP from group cipher list since it was not allowed for pairwise cipher
Priority group 5
id=0 ssid='Sirius'
Initializing interface (2) 'wlan0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Own MAC address: 00:04:23:80:03:78
Setting scan request: 0 sec 100000 usec
Wireless event: cmd=0x8b06 len=8
Trying to associate with SSID 'Sirius'
Cancelling scan request
Automatic auth_alg selection: 0x1
WPA: Set cipher suites based on configuration
WPA: Selected cipher suites: group 14 pairwise 8 key_mgmt 2
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Own WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8c07 len=52
Wireless event: cmd=0x8c08 len=35
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
Added BSSID 00:00:00:00:00:00 into blacklist
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
Disconnect event - remove keys
RX EAPOL from 00:11:50:06:13:7d
Setting authentication timeout: 10 sec 0 usec
EAPOL: Ignoring WPA EAPOL-Key frame in EAPOL state machines
IEEE 802.1X RX: version=1 type=3 length=95
EAPOL-Key type=254
WPA: RX message 1 of 4-Way Handshake from 00:11:50:06:13:7d (ver=1)
WPA: Renewed SNonce - hexdump(len=32): 14 61 1e 9d 11 c4 e8 26 58 51 4b cf 36 28 6c d7 41 5f 7f a0 64 30 44 77 2c d8 4f 3e 90 22 c8 99
WPA: PMK - hexdump(len=32): [REMOVED]
WPA: PTK - hexdump(len=64): [REMOVED]
WPA: EAPOL-Key MIC - hexdump(len=16): 46 38 1f 13 7f 8b 64 24 ee f8 07 c4 be fa 70 fe
WPA: Sending EAPOL-Key 2/4
Wireless event: cmd=0x8c07 len=52
Wireless event: cmd=0x8c08 len=35
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:11:50:06:13:7d
Association event - clear replay counter
Associated to a new BSS: BSSID=00:11:50:06:13:7d
No keys have been configured - skip key clearing
Network configuration found for the current AP
WPA: Using WPA IE from AssocReq to set cipher suites
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Own WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Associated with 00:11:50:06:13:7d
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
RX EAPOL from 00:11:50:06:13:7d
Setting authentication timeout: 10 sec 0 usec
EAPOL: Ignoring WPA EAPOL-Key frame in EAPOL state machines
IEEE 802.1X RX: version=1 type=3 length=95
EAPOL-Key type=254
WPA: RX message 1 of 4-Way Handshake from 00:11:50:06:13:7d (ver=1)
WPA: Renewed SNonce - hexdump(len=32): 80 54 ba 55 85 94 0d eb a7 88 28 27 a6 74 03 02 47 da 93 6d 39 42 19 f3 38 97 42 22 11 32 79 86
WPA: PMK - hexdump(len=32): [REMOVED]
WPA: PTK - hexdump(len=64): [REMOVED]
WPA: EAPOL-Key MIC - hexdump(len=16): 0f 32 d7 3a ff 47 01 32 4c 65 de 5b b7 0d 87 2d
WPA: Sending EAPOL-Key 2/4
Wireless event: cmd=0x8c07 len=52
Wireless event: cmd=0x8c08 len=35
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:11:50:06:13:7d
Association event - clear replay counter
Associated with 00:11:50:06:13:7d
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
RX EAPOL from 00:11:50:06:13:7d
Setting authentication timeout: 10 sec 0 usec
EAPOL: Ignoring WPA EAPOL-Key frame in EAPOL state machines
IEEE 802.1X RX: version=1 type=3 length=95
EAPOL-Key type=254
WPA: RX message 1 of 4-Way Handshake from 00:11:50:06:13:7d (ver=1)
WPA: Renewed SNonce - hexdump(len=32): bd d8 12 84 a3 48 37 4e 06 19 48 18 3f 42 04 f0 34 03 bb f1 eb 08 5b 13 df dd 4d 04 16 6a 2e 60
WPA: PMK - hexdump(len=32): [REMOVED]
WPA: PTK - hexdump(len=64): [REMOVED]
WPA: EAPOL-Key MIC - hexdump(len=16): c5 06 12 c0 fa 6b fc 1a 98 fd 8c d1 23 54 0d 1b
WPA: Sending EAPOL-Key 2/4
Wireless event: cmd=0x8c07 len=52
Wireless event: cmd=0x8c08 len=35
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:11:50:06:13:7d
Association event - clear replay counter
Associated with 00:11:50:06:13:7d
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
RX EAPOL from 00:11:50:06:13:7d
Setting authentication timeout: 10 sec 0 usec
EAPOL: Ignoring WPA EAPOL-Key frame in EAPOL state machines
IEEE 802.1X RX: version=1 type=3 length=95
EAPOL-Key type=254
WPA: RX message 1 of 4-Way Handshake from 00:11:50:06:13:7d (ver=1)
WPA: Renewed SNonce - hexdump(len=32): 7d b6 83 ec 78 38 cd b7 a2 5d 6b 4e 9f 13 5e 09 d6 10 a7 bb c7 a6 4c 6f 88 3c 20 15 6f 59 2c ba
WPA: PMK - hexdump(len=32): [REMOVED]
WPA: PTK - hexdump(len=64): [REMOVED]
WPA: EAPOL-Key MIC - hexdump(len=16): ba 1b 1c 32 db 12 fc 77 da 43 4f 4c 94 b1 70 05
WPA: Sending EAPOL-Key 2/4
Wireless event: cmd=0x8c07 len=52
Wireless event: cmd=0x8c08 len=35
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:11:50:06:13:7d
Association event - clear replay counter
Associated with 00:11:50:06:13:7d
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
RX EAPOL from 00:11:50:06:13:7d
Setting authentication timeout: 10 sec 0 usec
EAPOL: Ignoring WPA EAPOL-Key frame in EAPOL state machines
IEEE 802.1X RX: version=1 type=3 length=95
EAPOL-Key type=254
WPA: RX message 1 of 4-Way Handshake from 00:11:50:06:13:7d (ver=1)
WPA: Renewed SNonce - hexdump(len=32): ee 0e 15 df 8d fc 8f 27 19 db e6 21 fc 0c 6c fa f8 af 2b 46 22 f8 e9 b7 42 b4 94 e8 05 49 96 2a
WPA: PMK - hexdump(len=32): [REMOVED]
WPA: PTK - hexdump(len=64): [REMOVED]
WPA: EAPOL-Key MIC - hexdump(len=16): a3 a7 e5 5e cb ac 8a e2 5e 59 da 37 a3 cf 3d 24
WPA: Sending EAPOL-Key 2/4
Wireless event: cmd=0x8c07 len=52
Wireless event: cmd=0x8c08 len=35
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:11:50:06:13:7d
Association event - clear replay counter
Associated with 00:11:50:06:13:7d
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
RX EAPOL from 00:11:50:06:13:7d
Setting authentication timeout: 10 sec 0 usec
EAPOL: Ignoring WPA EAPOL-Key frame in EAPOL state machines
IEEE 802.1X RX: version=1 type=3 length=95
EAPOL-Key type=254
WPA: RX message 1 of 4-Way Handshake from 00:11:50:06:13:7d (ver=1)
WPA: Renewed SNonce - hexdump(len=32): 74 8c 0a c4 37 0b 41 69 db 8a de 62 d0 3f c0 92 d0 98 44 89 e4 ad 52 e8 5f a4 50 eb 71 a2 c8 d1
WPA: PMK - hexdump(len=32): [REMOVED]
WPA: PTK - hexdump(len=64): [REMOVED]
WPA: EAPOL-Key MIC - hexdump(len=16): 1b b4 6e a3 5e a6 30 7f eb 8e 7a f7 79 f8 e5 ad
WPA: Sending EAPOL-Key 2/4
Wireless event: cmd=0x8c07 len=52
Wireless event: cmd=0x8c08 len=35
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:11:50:06:13:7d
Association event - clear replay counter
Associated with 00:11:50:06:13:7d
EAPOL: External notification - portEnabled=0
More information about the Hostap
mailing list