wpa_supplicant + ndiswrapper authentication timeout

[Felix Dorner]

hi,

I cannot connect to my wpa-psk protected network. it seems like the 
authentication always times out. i have sucessfully installed 
ndiswrapper and wlan0 is up. here is the information that i can give:

This was used for building (.config)

CONFIG_WIRELESS_EXTENSION=y
CONFIG_DRIVER_NDISWRAPPER=y
CONFIG_CTRL_IFACE=y



This is my configuration file:

ctrl_interface=/var/run/wpa_supplicant
network={
ssid="sunset_diner"
psk="wonttellyou"
key_mgmt=WPA-PSK
}



This is the output of the program:

#wpa_supplicant -Dndiswrapper -iwlan0 -c/etc/wpa_supplicant.conf -dd
Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 
'ndiswrapper'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
Line: 3 - start of a new network block
ssid - hexdump_ascii(len=12):
     73 75 6e 73 65 74 5f 64 69 6e 65 72               sunset_diner
PSK (ASCII passphrase) - hexdump_ascii(len=16): [REMOVED]
key_mgmt: 0x2
PSK (from passphrase) - hexdump(len=32): [REMOVED]
Priority group 0
   id=0 ssid='sunset_diner'
Initializing interface (2) 'wlan0'
Own MAC address: 00:90:4b:55:28:68
Setting scan request: 0 sec 100000 usec
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Starting AP scan (broadcast SSID)
Scan timeout - try to get results
Received 320 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
0: 00:04:0e:2e:0f:3c ssid='sunset_diner' wpa_ie_len=24 rsn_ie_len=0
   selected
Trying to associate with 00:04:0e:2e:0f:3c (SSID='sunset_diner' 
freq=2437 MHz)
Cancelling scan request
Automatic auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Own WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 
01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
Setting authentication timeout: 5 sec 0 usec
Authentication with 00:00:00:00:00:00 timed out.
Added BSSID 00:00:00:00:00:00 into blacklist
No keys have been configured - skip key clearing
Setting scan request: 0 sec 0 usec
Starting AP scan (broadcast SSID)
Signal 2 received - terminating
No keys have been configured - skip key clearing
Removed BSSID 00:00:00:00:00:00 from blacklist (clear)

after that it starts with AP scan again... this repeats until I cancel 
with Ctrl+C


I have no clue what I make wrong. Thanks for any suggestions.

Felix