More succinct question

[Peter]

can you try again with any other irq than 3,4 or 7?


On Mon, 5 Jul 2004 22:03:14 -0400 (EDT)
Colin Worth <cworth at buphy.bu.edu> wrote:

> 
> Hostap sets up my Harmony 802.11b card to work at Vcc=5.0 volts even
> though the card says Vcc=3.3 on it, it is initially set to Vcc=3.3 in 
> prism2_attach() and I use ignore_cis_vcc=1.  Then all the commands
> sent to it time out.  What is wrong?
> 
> (debug messages below)
> 
> > Here is the output with options: ignore_cis_vcc=1:
> > 
> > (I also tried no_primary=1 and that did not change the output):
> > 
> > Jul  4 16:58:30 debian kernel: hostap_crypt: registered algorithm
> > 'NULL' Jul  4 16:58:30 debian kernel: hostap_cs: 0.2.2 - 2004-05-31
> > (Jouni Malinen <jkm
> > aline at cc.hut.fi>)
> > Jul  4 16:58:31 debian kernel: hostap_cs: setting Vcc=33 (constant)
> > Jul  4 16:58:31 debian kernel: hostap_cs: CS_EVENT_CARD_INSERTION
> > Jul  4 16:58:31 debian kernel: hostap_cs: ignoring Vcc=50 (from
> > config) Jul  4 16:58:31 debian kernel: enabled conf.attributes
> > |=CONF_ENABLE_IRQ
> > Jul  4 16:58:31 debian kernel: IO window settings: cfg->io.nwin=1 
> > dflt.io.nwin=1
> > Jul  4 16:58:31 debian kernel: io->flags = 0x0046, io.base=0x0000,
> > len=64 Jul  4 16:58:31 debian kernel: hostap_cs: Registered
> > netdevice wifi0 Jul  4 16:58:31 debian kernel: hostap_cs: index
> > 0x01: Vcc 5.0, irq 3, io 0x0100-
> > 0x013f
> > Jul  4 16:58:31 debian kernel: prism2_hw_init: initialized in 90 ms
> > Jul  4 16:58:31 debian kernel: wifi0: valid PDA not found
> > Jul  4 16:58:33 debian kernel: wifi0: hfa384x_cmd: entry still in
> > list? (entry=c
> > 111f160, type=0, res=0)
> > Jul  4 16:58:33 debian kernel: wifi0: hfa384x_cmd: command was not 
> > completed (re
> > s=0, entry=c111f160, type=0, cmd=0x0021, param0=0xfd02, EVSTAT=0000 
> > INTEN=0010)
> > Jul  4 16:58:33 debian kernel: wifi0: hfa384x_get_rid:
> > CMDCODE_ACCESS failed (re
> > s=-110, rid=fd02, len=8)
> > Jul  4 16:58:33 debian kernel: Could not get RID for component PRI
> > Jul  4 16:58:33 debian kernel: hostap_cs: Initialization failed
> > Jul  4 16:58:33 debian kernel: Registered client in prism2_attach
> > 
> > 
> > cardctl ident:
> > Socket 0:
> >   product info: "PROXIM", "Harmony 802.11b/LAN PC CARD", ""
> >   manfid: 0x0126, 0x8000
> >   function: 6 (network)
> > Socket 1:
> >   no product info available
> > 
> > 
> > cardctl config:
> > Socket 0:
> >   Vcc 5.0V  Vpp1 0.0V  Vpp2 0.0V
> >   interface type is "memory and I/O"
> >   irq 3 [exclusive] [level]
> >   function 0:
> >     config base 0x03e0
> >       option 0x41
> >     io 0x0100-0x013f [16bit]
> > Socket 1:
> >   not configured
> > 
> > 
> > dump_cis:
> > Socket 0:
> >   dev_info
> >     NULL 0ns, 512b
> >   attr_dev_info
> >     SRAM 500ns, 1kb
> >   vers_1 5.0, "PROXIM", "Harmony 802.11b/LAN PC CARD", ""
> >   manfid 0x0126, 0x8000
> >   funcid network_adapter
> >   lan_technology wireless
> >   lan_speed 1 mb/sec
> >   lan_speed 2 mb/sec
> >   lan_media 2.4_GHz
> >   lan_connector Closed connector standard
> >   config base 0x03e0 mask 0x0001 last_index 0x02
> >   cftable_entry 0x01 [default]
> >     Vcc Vnom 3300mV Vmin 3V Vmax 3600mV Iavg 300mA
> >     Ipeak 300mA Idown 10mA
> >     io 0x0000-0x003f [lines=6] [16bit]
> >     irq mask 0xffff [level] [pulse]
> > 
> > Socket 1:
> >   no CIS present
> > 
> > 
> > cardctl info:
> > PRODID_1="PROXIM"
> > PRODID_2="Harmony 802.11b/LAN PC CARD"
> > PRODID_3=""
> > PRODID_4=""
> > MANFID=0126,8000
> > FUNCID=6
> > PRODID_1=""
> > PRODID_2=""
> > PRODID_3=""
> > PRODID_4=""
> > MANFID=0000,0000
> > FUNCID=255
> > cardctl status:
> > Socket 0:
> >   5V 16-bit PC Card
> >   function 0: [ready]
> > Socket 1:
> >   no card
> > 
> > 
> _______________________________________________
> HostAP mailing list
> HostAP at shmoo.com
> http://lists.shmoo.com/mailman/listinfo/hostap