WEP problem - HostAP 0.0.4, Netgear MA401, Linksys WPC11

Ronan Mullally ronan
Tue Sep 23 16:31:04 PDT 2003


Hi,

I've yet to make any progress on this ;-(

I've successfully flashed all cards using the latest prism2_srec to the 
following:

	NIC: id=0x8013 v1.0.0
	PRI: id=0x15 v1.1.1
	STA: id=0x1f v1.7.4

I can still successfully associate when running the laptops under Linux
with or without WEP, but when running Windows with WEP enabled all I see
from the AP is:

Sep 24 00:10:08 Oook wlan0: 00:06:25:2a:b1:d8 auth_cb - STA authenticated
Sep 24 00:10:08 Oook wlan0: 00:06:25:2a:b1:d8 assoc_cb - STA associated
Sep 24 00:10:09 Oook wlan0: 00:06:25:2a:b1:d8 auth_cb - STA authenticated
Sep 24 00:10:09 Oook wlan0: 00:06:25:2a:b1:d8 assoc_cb - STA associated
Sep 24 00:11:06 Oook handle_ap_item - addr3(BSSID)=2a:67:20:68:80:3d not own MAC
Sep 24 00:11:27 Oook wlan0: 00:06:25:2a:b1:d8 auth_cb - STA authenticated
Sep 24 00:11:27 Oook wlan0: 00:06:25:2a:b1:d8 assoc_cb - STA associated

(The 'not own MAC' line corresponds to me re-selecting the 'active 
profile' in the linksys config utility)

I *should* be seeing a DHCP request next.

Any ideas?


-Ronan


On Mon, 22 Sep 2003, Ronan Mullally wrote:

> Hi,
> 
> Apologies if this is an FAQ.  I've had a quick look through the archives, 
> but didn't see anything recent which would help me.
> 
> I've got a box running 2.4.22 and HostAP 0.0.4.  It's got a Netgear MA401
> PCI card installed and acts as my AP.  I'm running secondary firmware 
> 1.4.9 from RAM on the card:
> 
> NICID: id=0x8013 v1.0.0 (PRISM II (2.5) Mini-PCI (SST parallel flash))
> PRIID: id=0x0015 v1.0.7
> STAID: id=0x001f v1.4.9 (station firmware)
> 
> I'm not running hostapd, just configuring wlan0 in master mode.  I have
> WEP enabled.
> 
> I've got two laptops with Linksys WPC11 v3 cards (I don't have firmware
> version numbers to hand, sorry).  I've no trouble running these cards
> under Linux with WEP enabled - everything works fine.  I'm not using
> hostap on the laptops - just the standard orinoco/hermes driver that 
> comes with RedHat 9.
> 
> When I try running these cards in Windows (Win2K) however I'm only able to
> run them with WEP disabled.  Once I turn on WEP the cards will associate
> with the AP but no IP traffic is exchanged between the laptop and the AP.
> 
> I'm guessing I have a WEP problem.  Under Linux the cards are configured
> with 'iwconfig <i/f> enc ...'.  Under Windows I'm using the Linksys 
> configuration utility.  I've tried the one the cards shipped with as well 
> as the current version from the Linksys website.
> 
> I've spent a bit of time trying to figure this out, but gotten nowhere.
> Does anybody have any suggestions?
> 
> 
> -Ronan
> 
> 
> _______________________________________________
> HostAP mailing list
> HostAP at shmoo.com
> http://lists.shmoo.com/mailman/listinfo/hostap
> 
> 





More information about the Hostap mailing list