Problems with hostap-0.0.3 an 2.4.21-rc6 /wolk 4.0s
Ruben Puettmann
ruben
Thu Jun 12 13:09:02 PDT 2003
hy,
since I try to update from my old 2.4.19 with hostap to a newer Version
I get much trouble.
I have try 2.4.21-rc6 + hostap 0.0.3 and an new WOLK (
http://wolk.sourceforge.net)
I can not find any errors in the log files. I have here an Debian
Sarge.
The wireless Card is an :
00:13.0 Network controller: National Datacomm Corp: Unknown device 0131
(rev 01)
It runs with the plx driver.
The Interrupts seems to be O.K. :
cat /proc/interrupts
CPU0
0: 396468 XT-PIC timer
1: 2 XT-PIC keyboard
2: 0 XT-PIC cascade
5: 37743 XT-PIC NE2000
7: 3184 XT-PIC wlan0
8: 4 XT-PIC rtc
10: 38978 XT-PIC eth0
12: 462 XT-PIC b1pci-e800
14: 6860 XT-PIC ide0
15: 1168 XT-PIC ide1
NMI: 0
LOC: 0
ERR: 0
MIS: 0
The ap will be startet with :
iface wlan0 inet static
address 192.168.1.1
netmask 255.255.255.0
network 192.168.1.0
broadcast 192.168.1.255
wireless_essid WLAN000001
wireless_mode Master
wireless_channel 4
wireless_nick fw-1
wireless_rate 11M
wireless_txpower 200mW
up /sbin/modprobe hostap_crypt
up /sbin/modprobe hostap_crypt_wep
up /usr/sbin/hostap_crypt_conf -1t wlan0 ff:ff:ff:ff:ff:ff WEP
6ec19428ee08a86af1e7944d95
The client is an prism2 card (Dlink 650) with wlan_ng driver. The client
has run with the old modules an 2.4.19 without problems. Now I get an
error like these :
ping 192.168.1.10
PING 192.168.1.10 (192.168.1.10): 56 data bytes
64 bytes from 192.168.1.10: icmp_seq=0 ttl=64 time=2216.5 ms
64 bytes from 192.168.1.10: icmp_seq=0 ttl=64 time=2217.6 ms (DUP!)
64 bytes from 192.168.1.10: icmp_seq=0 ttl=64 time=2218.8 ms (DUP!)
64 bytes from 192.168.1.10: icmp_seq=0 ttl=64 time=2225.3 ms (DUP!)
64 bytes from 192.168.1.10: icmp_seq=0 ttl=64 time=2227.4 ms (DUP!)
64 bytes from 192.168.1.10: icmp_seq=0 ttl=64 time=2228.4 ms (DUP!)
64 bytes from 192.168.1.10: icmp_seq=0 ttl=64 time=2229.5 ms (DUP!)
64 bytes from 192.168.1.10: icmp_seq=0 ttl=64 time=2230.7 ms (DUP!)
--- 192.168.1.10 ping statistics ---
4 packets transmitted, 1 packets received, +7 duplicates, 75% packet
loss
round-trip min/avg/max = 2216.5/2224.2/2230.7 ms
without any error in syslog oder dmesg
iwconfig wlan0
wlan0 IEEE 802.11b ESSID:"WLAN000001" Nickname:"fw-1"
Mode:Master Frequency:2.427GHz Access Point:
00:80:C6:E3:69:1A
Bit Rate=11Mb/s Tx-Power=24 dBm Sensitivity=1/3
Retry min limit:8 RTS thr:off Fragment thr:off
Encryption key:6EC1-9428-EE08-A86A-F1E7-944D-95 Encryption
mode:restricted
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:3 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
seems good to...
Output from hostap_diag is attached.
Now my knowledge ends. Can you help me ?
thx
Ruben
Host AP driver diagnostics information for 'wlan0'
NICID: id=0x8003 v1.0.0 (HWB3163 Rev B, Samsung PC Card Rev. B)
PRIID: id=0x0015 v0.3.0
STAID: id=0x001f v0.8.3 (station firmware)
Known RIDs (Resource IDentifiers)
FC00=CNFPORTTYPE=6
FC01=CNFOWNMACADDR=00:80:c6:e3:69:1a
FC02=CNFDESIREDSSID=WLAN000001
FC03=CNFOWNCHANNEL=4
FC04=CNFOWNSSID=WLAN000001
FC05=CNFOWNATIMWINDOW=0
FC06=CNFSYSTEMSCALE=1
FC07=CNFMAXDATALEN=2304
FC08=CNFWDSADDRESS=00:00:00:00:00:00
FC09=CNFPMENABLED=0
FC0A=CNFPMEPS=0
FC0B=CNFMULTICASTRECEIVE=1
FC0C=CNFMAXSLEEPDURATION=100
FC0D=CNFPMHOLDOVERDURATION=100
FC0E=CNFOWNNAME=fw-1
FC10=CNFOWNDTIMPERIOD=1
FC20=UNKNOWN1=33
FC21=UNKNOWN2=33
FC23=CNFWEPDEFAULTKEYID=0
FC24=CNFDEFAULTKEY0=<21<00<24<fc<00<00
FC25=CNFDEFAULTKEY1=<21<00<25<fc<00<00
FC26=CNFDEFAULTKEY2=<21<00<26<fc<00<00
FC27=CNFDEFAULTKEY3=<21<00<27<fc<00<00
FC28=CNFWEPFLAGS=<93<00
FC2A=CNFAUTHENTICATION=1
FC2C=CNFTXCONTROL=512
FC2D=CNFROAMINGMODE=1
FC30=CNFRCVCRCERROR=0
FC31=CNFMMLIFE=65000
FC32=CNFALTRETRYCOUNT=7
FC33=CNFBEACONINT=100
FC35=CNFSTAPCFINFO=<01<00
FC40=CNFTIMCTRL=1
FC41=UNKNOWN3=<00<00<00<00<00<00
FC42=CNFTHIRTY2TALLY=0
FC80=GROUPADDRESSES=
FC81=CREATEIBSS=1
FC82=FRAGMENTATIONTHRESHOLD=2346
FC83=RTSTHRESHOLD=2347
FC84=TXRATECONTROL=8
FC85=PROMISCUOUSMODE=0
FCB0=CNFSHORTPREAMBLE=0
FCB3=CNFBASICRATES=<03<00
FCB4=CNFSUPPORTEDRATES=<08<00
FCE0=TICKTIME=2000
FCE1=SCANREQUEST=<ff<3f<20<00
FCE2=JOINREQUEST=<21<00<e2<fc<00<00<00<00
FD00=MAXLOADTIME=60000
FD01=DOWNLOADBUFFER=<60<00<00<00<00<10
FD02=PRIID=0x15 v0.3.0
FD03=PRISUPRANGE=0 0x03 1 1-2
FD04=CFIACTRANGES=1 0x02 1 1-1
FD0A=NICSERNUM=SA01000000<00<00
FD0B=NICID=0x8003 v1.0.0
FD0C=MFISUPRANGE=0 0x01 1 1-1
FD0D=CFISUPRANGE=0 0x02 1 1-1
FD10=CHANNELLIST=<ff<1f
FD11=REGULATORYDOMAINS=0
FD12=TEMPTYPE=1
FD13=CIS=<01<03<00<00<ff<17<04<67<5a<08<ff<1d<05<03<67<5a<08<ff<15<50<05<00<49<45<45<45<20<38<30<32<2e<31<31<62<00<57<69<72<65<6c<65<73<73<20<4c<41<4e<20<50<43<20<43<61<72<64<2f<31<31<4d<00<56<65<72<73<69<6f<6e<20<30<31<2e<30<32<00<00<00<00<00<00<00<00<00<00<00<00<00<00<00<00<00<00<00<00<00<00<00<00<00<00<ff<20<04<56<01<02<00<21<02<06<00<22<02<01<07<22<05<02<40<42<0f<00<22<05<02<80<84<1e<00<22<05<02<60<ec<53<00<22<05<02<c0<d8<a7<00<22<02<03<07<22<08<04<06<00<80<c5<e3<0e<d6<22<02<05<01<1a<07<03<01<e0<03<00<00<01<1b<10<c1<01<19<77<b5<1e<35<b5<3c<36<36<05<46<7f + 295*<ff
FD20=STAID=0x1f v0.8.3
FD21=STASUPRANGE=0 0x04 1 1-6
FD22=MFIACTRANGES=1 0x01 1 1-1
FD23=CFIACTRANGES2=1 0x02 1 1-1
FD40=PORTSTATUS=8
FD41=CURRENTSSID=WLAN000001
FD42=CURRENTBSSID=00:80:c6:e3:69:1a
FD43=COMMSQUALITY=<00<00<1b<00<1b<00
FD44=CURRENTTXRATE=2
FD45=CURRENTBEACONINTERVAL=100
FD46=CURRENTSCALETHRESHOLDS=<36<00<36<00<36<00<0a<00<02<00<06<00
FD47=PROTOCOLRSPTIME=100
FD48=SHORTRETRYLIMIT=8
FD49=LONGRETRYLIMIT=5
FD4A=MAXTRANSMITLIFETIME=512
FD4B=MAXRECEIVELIFETIME=512
FD4C=CFPOLLABLE=0
FD4D=AUTHENTICATIONALGORITHMS=<01<00<01<00
FD4F=PRIVACYOPTIONIMPLEMENTED=1
FD88=SCANRESULTSTABLE=<01<00<03<00
FDC0=PHYTYPE=2
FDC1=CURRENTCHANNEL=4
FDC2=CURRENTPOWERSTATE=1
FDC3=CCAMODE=2
FDC6=SUPPORTEDDATARATES=<02<04<0b<16
FFFE=BUILDSEQ=<00<00<00<00
FFFF=FWID=0003C0.HEX<00<00S10008C3.HEX<00<00<00<00
Unknown RIDs (Resource IDentifiers)
Baseband proccessor (BBP) Configuration Registers
CR0 (Part/Version Code): 19 - Part=1 (HFA3861B series) Version=3 (3861B Version)
CR1 (I/O Polarity): 19 (normal setting 0)
Phase of RX carrier rotation sense: normal rotation (CCW)
Phase of TX carrier rotation sense: normal rotation (CCW)
Phase of TX output clock (TXCLK) pin: NON-Inverted TXCLK
Active level of the Transmit Ready output: TX_RDY Active 0
Active level of the transmit enable input: TX_PE Active 1
Active level of the Clear Channel Assessment output: CCA Active 0
Active level of the MD_RDY output: MD_RDY Active 0
Phase of the RX_CLK output: Invert Clk
CR2 (I Cover Code): 72 (nominally 72)
CR3 (Q Cover Code): 72 (nominally 72)
CR4 (TX Preamble Length): 128 (IEEE 802.11: 128)
CR5 (TX Signal Field): 1
Preamble mode: Normal
TX data rate: 01 = DQPSK - 11 chip sequence (2Mbps)
CR6 (TX Service Field): 0
CR7 (TX Length Field, High): 1
CR8 (TX Length Field, Low): 8
TX Length Field: 264 usec
CR9 (TX Configure): 162
CCA sample mode time: 15.8 usec
CCA mode: CCA is based on (CS1 OR SQ1/CS2)
TX test modes: Alternating bits for carrier suppression test
Enable TX test modes: normal operation
Antenna choice for TX: Set AntSel low
TX Antenna Mode: set AntSel pin to antenna for which last valid header CRC occurred
CR10 (RX Configure): 184
Initial CS2 estimate: Use SQ1 from Barker correlator peaks
CIR estimate/Dot product clock control: on during acquisition
SFD Time-out values: 64 usec
MD_RDY control: After SFD
Force Frequency Offset Estimating in all antenna diversity timelines: disabled
Antenna choice for RX when single antenna acquisition is selected: AntSel pin low
Antenna acquire: dual antenna for diversity acquisition
CR11 (RX/TX Configure): 27
Continuous internal RX 22 and 44 MHZ clocks: 0
A/D input coupling: DC
TX filter / CMF weight select: US
Ping Pong Differential Encode: normal
CCA mode: Sampled CCA; CCA will update once per slot (20 usec)
Precursor value in CIR estimate: 3
CR12 (A/D Test Modes 1): 0
All DAC and A/D clock source control: normal internal clocks
TX DAC clock: enable
RX DAC clock: enable
I DAC clock: enable
Q DAC clock: enable
RF A/D clock: enable
I A/D clock: enable
Q A/D clock: enable
CR13 (A/D Test Modes 2): 0
Standby: disable
SLEEP TX: disable
SLEEP RX: disable
SLEEP IQ: disable
Analog TX Shut_down: disable
Analog RX Shut_down: disable
Analog Standby: disable
Manual control of mixed signal power down signals (other CR13 bits): disable
CR14 (A/D Test Modes 3): 0
DFS - select straight binary output of I/Q and RF A/D converters: 0
I/Q DAC input control: normal (TX filter)
Enable test bus into RX and TX DAC: disable
Enable RF A/D into RX DAC: disable
VRbit1: 0
VRbit0: 0
CR15 (AGC GainClip): 92
CR16 (AGC Sat Cpints): 130
AGC mid Sat counts: 8
AGC low Sat counts: 2
CR17 (AGC Update Control): 32
AGC update during CIR injest: disable
AGC timer count: 32 (must be 31)
CR18 (AGC HiSat): 196
CR19 (AGC LockinLevel/CW detect threshold): 23
CR20 (AGC LockWindow, pos side): 10
CR21 (AGC Threshold): 14
CR22 (AGC Lookup Table Addr and Control): 31
CR23 (AGC Lookup Table Data): 127
CR24 (AGC LoopGain): 45
CR25 (AGC RX_IF): 32
CR26 (AGC Test Modes): 144
CR27 (AGC RX_RF Threshold): 24
CR28 (AGC Low SatAtten): 118
CR29 (AGC LockWindow, negative side): 10
CR30 (Carrier Sense 2): 36
CR31 (Manual TX Power Control): 192
CR32 (Test Modes 1): 0
CR33 (Test Modes 2): 0
CR34 (Test Bus Address): 0
CR35 (CMF Coefficient Control): 12
CR36 (Scrambler Seed, Long Preamble Option): 38
CR37 (Scrambler Seed, Short Preamble Option): 91
CR38 (ED Threshold): 127
CR39 (CMF Gain Threshold): 41
CR40 (Threshold for antenna decision): 15
CR41 (Preamble tracking loop lead coefficient): 32
CR42 (Preamble tracking loop lag coefficient): 32
CR43 (Header tracking loop lead coefficient): 16
CR44 (Header tracking loop lag coefficient): 16
CR45 (Data tracking loop lead coefficient): 16
CR46 (Data tracking loop lag coefficient): 16
CR47 (RF attenuator value): 30
CR48 (ED and SQ1 control and SQ1 scale factor): 30
CR49 (Read only register mux control for registers 50 to 63): 152
CW RSSI threshold: 24
CR50..CR63: 'a' value
CR50 (Test Bus Read): 0
CR51 (Noise floorAntA): 1
CR52 (Noise floorAntB): 0
CR53 (AGC error): 127
CR54 (Unassigned): 0
CR55 (Unassigned): 0
CR56 (Unassigned): 0
CR57 (Unassigned): 0
CR58 (TX Power Measurement): 196
CR59 (RX Mean Power): 8
CR60 (RX_IF AGC): 17
CR61 (RX Status Reg): 13
CR62 (RSSI): 2
CR63 (RX Status Reg): 0
--
Ruben Puettmann
ruben at puettmann.net
http://www.puettmann.net
More information about the Hostap
mailing list