[PATCH v2] ARM: karo-tx6: enable deep-probe

[Ahmad Fatoum]

Hi,

On 11.11.25 18:16, Fabian Pfitzner wrote:
> We have two baseboards using this SoM mainline sharing the same board
> code that is not yet deep probe compatible, because they expect i2c0 to
> be available at device_initcall level.
> 
> Make the board code deep probe compatible and enable deep probe for all
> boards using this SoM. Out-of-tree board code will need to adapt
> accordingly, so note that in the migration guide.
> 
> Signed-off-by: Fabian Pfitzner <f.pfitzner at pengutronix.de>

Sorry, but I haven't looked proprly. :(

You are only changing the two board device trees, so this is not actually
correct...

Either we should add barebox,deep-probe into imx6qdl-tx6x.dtsi and remove
the disables from the board device tree or we leave them as-is and just
drop the migration guide node and adapt the commit message...


Sorry for the confusion.

Thanks,
Ahmad

> ---
>  Documentation/migration-guides/migration-master.rst | 12 ++++++++++++
>  arch/arm/boards/karo-tx6x/board.c                   |  2 ++
>  arch/arm/dts/imx6dl-tx6u.dts                        |  2 +-
>  arch/arm/dts/imx6q-tx6q.dts                         |  2 +-
>  4 files changed, 16 insertions(+), 2 deletions(-)
>  create mode 100644 Documentation/migration-guides/migration-master.rst
> 
> diff --git a/Documentation/migration-guides/migration-master.rst b/Documentation/migration-guides/migration-master.rst
> new file mode 100644
> index 0000000000..41b055d7fe
> --- /dev/null
> +++ b/Documentation/migration-guides/migration-master.rst
> @@ -0,0 +1,12 @@
> +Release Unknown
> +===============
> +
> +Board support
> +-------------
> +
> +Karo TX6X
> +^^^^^^^^^
> +
> +Deep probe has been enabled for this board. Out-of-tree board code for these
> +SoMs must either ensure devices are available as the in-tree code does or they
> +should add ``barebox,disable-deep-probe`` to their top level device tree node.
> diff --git a/arch/arm/boards/karo-tx6x/board.c b/arch/arm/boards/karo-tx6x/board.c
> index 43e23f00cd..1924660c11 100644
> --- a/arch/arm/boards/karo-tx6x/board.c
> +++ b/arch/arm/boards/karo-tx6x/board.c
> @@ -54,6 +54,8 @@ static int setup_pmic_voltages(void)
>  	int bus = 0;
>  	uint8_t reg;
>  
> +	of_device_ensure_probed_by_alias("i2c0");
> +
>  	adapter = i2c_get_adapter(bus);
>  	if (!adapter) {
>  		pr_err("i2c bus %d not found\n", bus);
> diff --git a/arch/arm/dts/imx6dl-tx6u.dts b/arch/arm/dts/imx6dl-tx6u.dts
> index 1055de9d80..c23673d729 100644
> --- a/arch/arm/dts/imx6dl-tx6u.dts
> +++ b/arch/arm/dts/imx6dl-tx6u.dts
> @@ -8,6 +8,6 @@
>  / {
>  	model = "Ka-Ro electronics TX6U-801x Module";
>  	compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
> -	barebox,disable-deep-probe;
> +	barebox,deep-probe;
>  };
>  
> diff --git a/arch/arm/dts/imx6q-tx6q.dts b/arch/arm/dts/imx6q-tx6q.dts
> index c2aacfc415..daf9549ea5 100644
> --- a/arch/arm/dts/imx6q-tx6q.dts
> +++ b/arch/arm/dts/imx6q-tx6q.dts
> @@ -8,6 +8,6 @@
>  / {
>  	model = "Ka-Ro electronics TX6Q Module";
>  	compatible = "karo,imx6q-tx6q", "fsl,imx6q";
> -	barebox,disable-deep-probe;
> +	barebox,deep-probe;
>  };
>  


-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |