[PATCH] net: ksz8864: Add support for KSZ87xx switches
Sascha Hauer
sha at pengutronix.de
Tue Oct 12 00:45:07 PDT 2021
On Mon, Oct 11, 2021 at 11:42:13AM -0700, Trent Piepho wrote:
> This adds support for the ksz8765, ksz8794, and ksz8795 switches.
>
> IDs for OF bindings are added. The base chip type is "ksz8795", the
> same as the Linux driver, for the ksz87xx switches added here.
> "ksz8864rmn" is used for the existing switch.
>
> The registers for these switch chips, as least as far as this simple
> driver is concerned, are the same as the existing ksz8864 support.
>
> The difference in the ksz87xx chips is the format of the command and
> address bytes:
>
> C = command
> A = address (used bits)
> a = address (unused bits)
> p = turn around padding bit
>
> ksz8864: 00000CCC AAAAAAAA
> ksz8795: CCCaaaaA AAAAAAAp
>
> CCC and AAAAAAAA are the same, it's just where they are that changes.
> This is parameterized in the read/write reg functions by using two
> values for the address width and pad width.
>
> Signed-off-by: Trent Piepho <trent.piepho at igorinstitute.com>
> ---
> drivers/net/ksz8864rmn.c | 66 ++++++++++++++++++++++++++++++----------
> 1 file changed, 50 insertions(+), 16 deletions(-)
Applied, thanks
Sascha
>
> diff --git a/drivers/net/ksz8864rmn.c b/drivers/net/ksz8864rmn.c
> index 85063ff0d..72ab86579 100644
> --- a/drivers/net/ksz8864rmn.c
> +++ b/drivers/net/ksz8864rmn.c
> @@ -31,48 +31,55 @@
> #define CMD_WRITE 0x02
> #define CMD_READ 0x03
>
> +enum ksz_type {
> + unknown,
> + ksz87,
> + ksz88
> +};
> +
> struct micrel_switch_priv {
> struct cdev cdev;
> struct spi_device *spi;
> unsigned int p_enable;
> + unsigned int addr_width;
> + unsigned int pad;
> };
>
> -static int micrel_switch_read_reg(struct spi_device *spi, uint8_t reg)
> +static int micrel_switch_read_reg(const struct micrel_switch_priv *priv, uint8_t reg)
> {
> uint8_t tx[2];
> uint8_t rx[1];
> int ret;
>
> - tx[0] = CMD_READ;
> - tx[1] = reg;
> + tx[0] = CMD_READ << (priv->addr_width + priv->pad - 8) | reg >> (8 - priv->pad);
> + tx[1] = reg << priv->pad;
>
> - ret = spi_write_then_read(spi, tx, 2, rx, 1);
> + ret = spi_write_then_read(priv->spi, tx, 2, rx, 1);
> if (ret < 0)
> return ret;
>
> return rx[0];
> }
>
> -static void micrel_switch_write_reg(struct spi_device *spi, uint8_t reg, uint8_t val)
> +static void micrel_switch_write_reg(const struct micrel_switch_priv *priv, uint8_t reg, uint8_t val)
> {
> uint8_t tx[3];
>
> - tx[0] = CMD_WRITE;
> - tx[1] = reg;
> + tx[0] = CMD_WRITE << (priv->addr_width + priv->pad - 8) | reg >> (8 - priv->pad);
> + tx[1] = reg << priv->pad;
> tx[2] = val;
>
> - spi_write_then_read(spi, tx, 3, NULL, 0);
> + spi_write_then_read(priv->spi, tx, 3, NULL, 0);
> }
>
> static int micrel_switch_enable_set(struct param_d *param, void *_priv)
> {
> struct micrel_switch_priv *priv = _priv;
> - struct spi_device *spi = priv->spi;
>
> if (priv->p_enable)
> - micrel_switch_write_reg(spi, REG_ID1, 1);
> + micrel_switch_write_reg(priv, REG_ID1, 1);
> else
> - micrel_switch_write_reg(spi, REG_ID1, 0);
> + micrel_switch_write_reg(priv, REG_ID1, 0);
>
> return 0;
> }
> @@ -84,7 +91,7 @@ static ssize_t micel_switch_read(struct cdev *cdev, void *_buf, size_t count, lo
> struct micrel_switch_priv *priv = cdev->priv;
>
> for (i = 0; i < count; i++) {
> - ret = micrel_switch_read_reg(priv->spi, offset);
> + ret = micrel_switch_read_reg(priv, offset);
> if (ret < 0)
> return ret;
> *buf = ret;
> @@ -102,7 +109,7 @@ static ssize_t micel_switch_write(struct cdev *cdev, const void *_buf, size_t co
> struct micrel_switch_priv *priv = cdev->priv;
>
> for (i = 0; i < count; i++) {
> - micrel_switch_write_reg(priv->spi, offset, *buf);
> + micrel_switch_write_reg(priv, offset, *buf);
> buf++;
> offset++;
> }
> @@ -119,6 +126,11 @@ static int micrel_switch_probe(struct device_d *dev)
> {
> struct micrel_switch_priv *priv;
> int ret = 0;
> + enum ksz_type kind = (enum ksz_type)device_get_match_data(dev);
> + uint8_t id;
> +
> + if (kind == unknown)
> + return -ENODEV;
>
> priv = xzalloc(sizeof(*priv));
>
> @@ -128,12 +140,27 @@ static int micrel_switch_probe(struct device_d *dev)
> priv->spi->mode = SPI_MODE_0;
> priv->spi->bits_per_word = 8;
>
> - ret = micrel_switch_read_reg(priv->spi, REG_ID0);
> + switch (kind) {
> + case ksz87:
> + priv->addr_width = 12;
> + priv->pad = 1;
> + id = 0x87;
> + break;
> + case ksz88:
> + priv->addr_width = 8;
> + priv->pad = 0;
> + id = 0x95;
> + break;
> + default:
> + return -ENODEV;
> + };
> +
> + ret = micrel_switch_read_reg(priv, REG_ID0);
> if (ret < 0) {
> dev_err(&priv->spi->dev, "failed to read device id\n");
> return ret;
> }
> - if (ret != 0x95) {
> + if (ret != id) {
> dev_err(&priv->spi->dev, "unknown device id: %02x\n", ret);
> return -ENODEV;
> }
> @@ -149,13 +176,20 @@ static int micrel_switch_probe(struct device_d *dev)
> NULL, &priv->p_enable, priv);
>
> priv->p_enable = 1;
> - micrel_switch_write_reg(priv->spi, REG_ID1, 1);
> + micrel_switch_write_reg(priv, REG_ID1, 1);
>
> return 0;
> }
>
> +static const struct platform_device_id ksz_ids[] = {
> + { .name = "ksz8864rmn", .driver_data = ksz88 },
> + { .name = "ksz8795", .driver_data = ksz87 },
> + { }
> +};
> +
> static struct driver_d micrel_switch_driver = {
> .name = "ksz8864rmn",
> .probe = micrel_switch_probe,
> + .id_table = ksz_ids,
> };
> device_spi_driver(micrel_switch_driver);
> --
> 2.31.1
>
>
> _______________________________________________
> barebox mailing list
> barebox at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
More information about the barebox
mailing list