reset / watchdog on an imx7d soc
Giorgio Dal Molin
giorgio.nicole at arcor.de
Mon Jun 29 12:33:45 EDT 2020
Hi,
> On June 29, 2020 at 6:11 PM Ahmad Fatoum <a.fatoum at pengutronix.de> wrote:
>
>
> On 6/29/20 6:03 PM, Giorgio Dal Molin wrote:
> > Hi,
> >
> >> On June 29, 2020 at 5:35 PM Ahmad Fatoum <a.fatoum at pengutronix.de> wrote:
> >>
> >>
> >> Hello Giorgio,
> >>
> >> On 6/29/20 5:30 PM, Giorgio Dal Molin wrote:
> >>> Hi,
> >>>
> >>>> On June 29, 2020 at 3:30 PM Ahmad Fatoum <a.fatoum at pengutronix.de> wrote:
> >>>>
> >>>>
> >>>> Hello,
> >>>>
> >>>> On 6/29/20 12:53 PM, Giorgio Dal Molin wrote:
> >>>>> Hi,
> >>>>>
> >>>>>> On June 29, 2020 at 10:44 AM Ahmad Fatoum <a.fatoum at pengutronix.de> wrote:
> >>>>>>
> >>>>>>
> >>>>>> Hello Giorgio,
> >>>>>>
> >>>>>> On 6/23/20 5:11 PM, Giorgio Dal Molin wrote:
> >>>>>>> Hi Fabio,
> >>>>>>>
> >>>>>>> thank you for your quick reply.
> >>>>>>>
> >>>>>>> I've already found the errata you linked in your mail but I had no success
> >>>>>>> applying the suggestion there; maybe I'm doing it wrong.
> >>>>>>> Let's take the Option 3 there:
> >>>>>>
> >>>>>> Does reset within Linux (with say the imx_v6_v7_defconfg) work?
> >>>>>
> >>>>> No. I see the same behavior also with the kernel: after a 'shutdown -r'
> >>>>> the system 'goes down' but doesn't reboot, it just hang:
> >>>>>
> >>>>> ~ # shutdown -r
> >>>>> system is going down for reboot NOW
> >>>>> ...
> >>>>> [ 46.248222] 000: ci_hdrc ci_hdrc.0: remove, state 1
> >>>>> [ 46.248253] 000: usb usb1: USB disconnect, device number 1
> >>>>> [ 46.248263] 000: usb 1-1: USB disconnect, device number 2
> >>>>>
> >>>>>
> >>>>> The same happens if I kill the 'watchdog' process: after ~2 seconds
> >>>>> the system just hangs.
> >>>>>
> >>>>> I'm sure there must be a solution because the original u-boot bootloader
> >>>>> for the cpu module I'm using reboots the system as expected, through the wdog1;
> >>>>> unfortunately it's not so trivial to find what makes the difference.
> >>>>
> >>>> Linux probably attempts reset via PSCI. Check for psci_system_reset
> >>>> in your vendor's U-Boot and transplant it into barebox.
> >>>
> >>> U-Boot has actually a psci_system_reset(), it also rely on wdog1:
> >>>
> >>> __secure void psci_system_reset(void)
> >>> {
> >>> struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
> >>>
> >>> /* make sure WDOG1 clock is enabled */
> >>> writel(0x1 << 28, CCM_BASE_ADDR + CCM_ROOT_WDOG);
> >>> writel(0x3, CCM_BASE_ADDR + CCM_CCGR_WDOG1);
> >>> writew(WCR_WDE, &wdog->wcr);
> >>>
> >>> while (1)
> >>> wfi();
> >>> }
> >>>
> >>> It is also compiled in the uboot image, because if I add a syntax error in
> >>> its body the compiler tells me; anyway I think it's not called when I issue
> >>> the 'reset' command at the prompt because the 'reset' works properly even if
> >>> I comment out the whole body of the function or if I add an endless loop like
> >>> while(1); to it.
> >>
> >> Yes. It should be called by the kernel when CONFIG_ARM_PSCI_FW=y
> >> and the device tree has the correct node.
> >>> Anyway I ported it to barebox, defining a void psci_system_reset(void) in
> >>> arch/arm/mach-imx/imx7.c:
> >>>
> >>> ...
> >>> #define CCM_BASE_ADDR 0x30380000
> >>> #define CCM_ROOT_WDOG 0xbb80
> >>> #define CCM_CCGR_WDOG1 0x49c8
> >>> #define WCR_WDE 0x04
> >>> #define WDOG1_WCR 0x30280000
> >>> #define wfi() __asm__ __volatile__ ("wfi" : : : "memory")
> >>>
> >>> static void imx7_system_reset(void)
> >>> {
> >>> printf("%s: called now.\n",__func__);
> >>>
> >>> // make sure WDOG1 clock is enabled
> >>> writel(0x1 << 28, CCM_BASE_ADDR + CCM_ROOT_WDOG);
> >>> writel(0x3, CCM_BASE_ADDR + CCM_CCGR_WDOG1);
> >>> writew(WCR_WDE, WDOG1_WCR);
> >>>
> >>> while (1)
> >>> wfi();
> >>> };
> >>>
> >>> static struct psci_ops imx7_psci_ops = {
> >>> .cpu_on = imx7_cpu_on,
> >>> .cpu_off = imx7_cpu_off,
> >>> .system_reset = imx7_system_reset,
> >>> };
> >>>
> >>> and the following case to smc.c:
> >>>
> >>> static int do_smc(int argc, char *argv[])
> >>> {
> >>> ...
> >>> case 'r':
> >>> printf("issue psci reset...\n");
> >>> arm_smccc_smc(ARM_PSCI_0_2_FN_SYSTEM_RESET,
> >>> 0, 0, 0, 0, 0, 0, 0, &res);
> >>> printf("reset issued...\n");
> >>> break;
> >>> ...
> >>>
> >>> to be able to call it.
> >>> Now, using the modified 'smc' command I can see my printf's:
> >>>
> >>> samx7: / smc -n
> >>> samx7: / smc -r
> >>> issue psci reset...
> >>> psci_system_reset called.
> >>> imx7_system_reset: called now.
> >>>
> >>> but the soc still just hangs.
> >>
> >> What does U-Boot's reset commando do on an i.MX7?
> >
> > It ends up calling this function in the imx_watchdog.c:
> >
> > void __attribute__((weak)) reset_cpu(ulong addr)
> > {
> > struct watchdog_regs *wdog = (struct watchdog_regs *)WDOG1_BASE_ADDR;
> >
> > printf("%s: called now\n",__func__);
> > udelay(500);
> >
> > clrsetbits_le16(&wdog->wcr, WCR_WT_MSK, WCR_WDE);
> >
> > writew(0x5555, &wdog->wsr);
> > writew(0xaaaa, &wdog->wsr); /* load minimum 1/2 second timeout */
> > while (1) {
> > /*
> > * spin for .5 seconds before reset
> > */
> > }
> > }
> >
> > I added the printf / udelay to be sure. WCR_WT_MSK is (0xff << 8).
>
> Hmm and same code doesn't reset it in barebox? That's strange.
> Is there something in the DCD table that you are missing in barebox?
U-Boot configures the ddr3 with c code in its board code 'lowlevel.c'.
Looking at the code I noticed this special treatment:
static void spl_dram_init(void)
{
...
/*
* Make sure that both aresetn/core_ddrc_rstn and preset/PHY reset
* bits are set after WDOG reset event. DDRC_PRST can only be
* released when DDRC clock inputs are stable for at least 30 cycles.
*/
writel(SRC_DDRC_RCR_DDRC_CORE_RST_MASK | SRC_DDRC_RCR_DDRC_PRST_MASK, &src_regs->ddrc_rcr);
udelay(500);
...
This writel() set both reset bits, the DDRC_CORE (0x2) and the DDRC_PRST (0x1) of the SRC
register 0x30391000.
Unfortunately, if I try also to set both bits in my DCD table then barebox doesn't boot anymore;
I also tried to port the uboot spl_dram_init(void) to my barebox lowlevel.c and I could eventually
boot barebox with an empty DCD but still adding the second bit (SRC_DDRC_RCR_DDRC_PRST_MASK)
hangs the soc.
giorgio
>
> >
> > What I also observed is that if I upload the uboot image with the imx-usb-loader it boots
> > and runs normally but the reset in this case also just hangs the soc without rebooting it,
> > like barebox; so there must be a difference between an 'usb uploaded' boot and a 'qspi native'
> > boot.
>
> Are you sure it's not resetting to serial download mode again?
>
> >
> > giorgio
> >
> >>
> >>>
> >>> giorgio
> >>>
> >>>>
> >>>>>
> >>>>> giorgio
> >>>>>
> >>>>>
> >>>>>>
> >>>>>> --
> >>>>>> Pengutronix e.K. | |
> >>>>>> Steuerwalder Str. 21 | http://www.pengutronix.de/ |
> >>>>>> 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
> >>>>>> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
> >>>>>>
> >>>>>> _______________________________________________
> >>>>>> barebox mailing list
> >>>>>> barebox at lists.infradead.org
> >>>>>> http://lists.infradead.org/mailman/listinfo/barebox
> >>>>>
> >>>>
> >>>> --
> >>>> Pengutronix e.K. | |
> >>>> Steuerwalder Str. 21 | http://www.pengutronix.de/ |
> >>>> 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
> >>>> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
> >>>>
> >>>> _______________________________________________
> >>>> barebox mailing list
> >>>> barebox at lists.infradead.org
> >>>> http://lists.infradead.org/mailman/listinfo/barebox
> >>>
> >>
> >> --
> >> Pengutronix e.K. | |
> >> Steuerwalder Str. 21 | http://www.pengutronix.de/ |
> >> 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
> >> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
> >>
> >> _______________________________________________
> >> barebox mailing list
> >> barebox at lists.infradead.org
> >> http://lists.infradead.org/mailman/listinfo/barebox
> >
>
> --
> Pengutronix e.K. | |
> Steuerwalder Str. 21 | http://www.pengutronix.de/ |
> 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
>
> _______________________________________________
> barebox mailing list
> barebox at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
More information about the barebox
mailing list