[PATCH v5 00/12] prepare Protonic board code for mainline

[Oleksij Rempel]

changes v5:
- board: apply requested changes
- add PHY and rs458 devicetree fixes for lanmcu and plym2m

changes v4:
- follow suggestion provided by Ahmad and open-code the root node
  registration and call it machine.of
- board: rename crc and cs
- board: ignore most of init related errors. Even if one part will fail,
  we should be able to get as mach as possible.

changes v3:
- remove barebox-serial driver and use read the rfid directy from board
  code (as was done in initial implementation)
- use initcall instead of registering driver in the board code
- add delayed USB scan
- add rampoops node
- add partition tables 

changes v2:
- add power init support for KvG boards
- spell fixes
- do not print error on probe exit
- add of_console_get_by_alias() helper
- free requested gpio array
- exit fec init only in case of PROBE_DEFERED

This patch series is a preparation and actual Protonic board code.
Following changes was made in the main code:
- register DT root node as device to make it possible to loade board
  code as usual driver
- provide helpers to read ethernet mac from nvmem cell register in a
  devicetree.
- provide barebox-serial driver which should be a nvmem cell consumer
  and
  serial-number DT property provider.
- provide gpio helper to read gpio based board revision.

Oleksij Rempel (12):
  of: base: register DT root as device
  gpiolib: add gpio_array_to_id helper to get ID out of GPIO array
  common: console_common: add of_console_get_by_alias() helper
  of: of_device_get_match_compatible() helper
  ARM: protonic-imx6: port Protonic specific board code
  ARM: dts: unify barebox and barebox,env partitions for all Protonic
    boards
  ARM: dts: imx6q-prti6q: add pstore/ramoops node
  ARM: dts: protonic: lanmcu: add eMMC partition table
  ARM: dts: protonic: add fixed clock for the FEC node
  ARM: dts: protonic: lanmcu: use UART_CTS instead of GPIO based CTS
  ARM: dts: protonic: properly define PHY nodes on lanmcu and plym2m
    boards
  ARM: dts: protonic: lanmcu: add uart-has-rtscts to enable rs485
    functionality

 arch/arm/boards/protonic-imx6/Makefile |    1 +
 arch/arm/boards/protonic-imx6/board.c  | 1034 ++++++++++++++++++++++++
 arch/arm/dts/imx6dl-lanmcu.dts         |   50 +-
 arch/arm/dts/imx6dl-plym2m.dts         |   51 +-
 arch/arm/dts/imx6dl-prtrvt.dts         |    1 +
 arch/arm/dts/imx6q-prti6q.dts          |   24 +-
 arch/arm/dts/imx6qdl-prti6q-nor.dtsi   |   10 +
 arch/arm/dts/imx6qdl-prti6q.dtsi       |   31 +
 arch/arm/dts/imx6qdl-vicut1.dtsi       |   26 +
 common/console_common.c                |   18 +
 drivers/gpio/gpiolib.c                 |   31 +
 drivers/of/base.c                      |   17 +
 drivers/of/device.c                    |   12 +
 include/console.h                      |    1 +
 include/gpio.h                         |    5 +
 include/of_device.h                    |    6 +
 16 files changed, 1282 insertions(+), 36 deletions(-)
 create mode 100644 arch/arm/boards/protonic-imx6/board.c
 create mode 100644 arch/arm/dts/imx6qdl-prti6q-nor.dtsi

-- 
2.28.0