[PATCH v3 4/6] ARM: protonic-imx6: port Protonic specific board code
Oleksij Rempel
o.rempel at pengutronix.de
Thu Aug 13 08:55:12 EDT 2020
Signed-off-by: Oleksij Rempel <o.rempel at pengutronix.de>
---
arch/arm/boards/protonic-imx6/Makefile | 1 +
arch/arm/boards/protonic-imx6/board.c | 1002 ++++++++++++++++++++++++
2 files changed, 1003 insertions(+)
create mode 100644 arch/arm/boards/protonic-imx6/board.c
diff --git a/arch/arm/boards/protonic-imx6/Makefile b/arch/arm/boards/protonic-imx6/Makefile
index b08c4a93ca..01c7a259e9 100644
--- a/arch/arm/boards/protonic-imx6/Makefile
+++ b/arch/arm/boards/protonic-imx6/Makefile
@@ -1 +1,2 @@
+obj-y += board.o
lwl-y += lowlevel.o
diff --git a/arch/arm/boards/protonic-imx6/board.c b/arch/arm/boards/protonic-imx6/board.c
new file mode 100644
index 0000000000..f3bd0dd86a
--- /dev/null
+++ b/arch/arm/boards/protonic-imx6/board.c
@@ -0,0 +1,1002 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// SPDX-FileCopyrightText: 2012 Steffen Trumtrar, Pengutronix
+// SPDX-FileCopyrightText: 2014 Protonic Holland
+// SPDX-FileCopyrightText: 2020 Oleksij Rempel, Pengutronix
+
+#include <bbu.h>
+#include <common.h>
+#include <environment.h>
+#include <gpio.h>
+#include <mach/bbu.h>
+#include <mach/imx6.h>
+#include <of_device.h>
+
+#include <usb/usb.h>
+#include <sys/mount.h>
+#include <sys/stat.h>
+#include <fcntl.h>
+#include <unistd.h>
+#include <net.h>
+#include <i2c/i2c.h>
+
+#define GPIO_HW_REV_ID {\
+ {IMX_GPIO_NR(2, 8), GPIOF_DIR_IN | GPIOF_ACTIVE_LOW, "rev_id0"}, \
+ {IMX_GPIO_NR(2, 9), GPIOF_DIR_IN | GPIOF_ACTIVE_LOW, "rev_id1"}, \
+ {IMX_GPIO_NR(2, 10), GPIOF_DIR_IN | GPIOF_ACTIVE_LOW, "rev_id2"} \
+}
+
+#define GPIO_HW_TYPE_ID {\
+ {IMX_GPIO_NR(2, 11), GPIOF_DIR_IN | GPIOF_ACTIVE_LOW, "hw_id0"}, \
+ {IMX_GPIO_NR(2, 12), GPIOF_DIR_IN | GPIOF_ACTIVE_LOW, "hw_id1"}, \
+ {IMX_GPIO_NR(2, 13), GPIOF_DIR_IN | GPIOF_ACTIVE_LOW, "hw_id2"}, \
+ {IMX_GPIO_NR(2, 14), GPIOF_DIR_IN | GPIOF_ACTIVE_LOW, "hw_id3"}, \
+ {IMX_GPIO_NR(2, 15), GPIOF_DIR_IN | GPIOF_ACTIVE_LOW, "hw_id4"} \
+}
+
+enum {
+ HW_TYPE_PRTI6Q = 0,
+ HW_TYPE_PRTWD2 = 1,
+ HW_TYPE_ALTI6S = 2,
+ HW_TYPE_VICUT1 = 4,
+ HW_TYPE_ALTI6P = 6,
+ HW_TYPE_PRTMVT = 8,
+ HW_TYPE_PRTI6G = 10,
+ HW_TYPE_PRTRVT = 12,
+ HW_TYPE_VICUT2 = 16,
+ HW_TYPE_PLYM2M = 20,
+ HW_TYPE_PRTVT7 = 22,
+ HW_TYPE_LANMCU = 23,
+ HW_TYPE_PLYBAS = 24,
+ HW_TYPE_VICTGO = 28,
+};
+
+enum prt_imx6_kvg_pw_mode {
+ PW_MODE_KVG_WITH_YACO = 0,
+ PW_MODE_KVG_NEW = 1,
+ PW_MODE_KUBOTA = 2,
+};
+
+/* board specific flags */
+#define PRT_IMX6_BOOTCHOOSER BIT(3)
+#define PRT_IMX6_USB_LONG_DELAY BIT(2)
+#define PRT_IMX6_BOOTSRC_EMMC BIT(1)
+#define PRT_IMX6_BOOTSRC_SPI_NOR BIT(0)
+
+static struct prt_imx6_priv *prt_priv;
+struct prt_machine_data {
+ unsigned int hw_id;
+ unsigned int hw_rev;
+ unsigned int i2c_addr;
+ unsigned int i2c_adapter;
+ unsigned int flags;
+ int (*init)(struct prt_imx6_priv *priv);
+};
+
+struct prt_imx6_priv {
+ struct device_d *dev;
+ const struct prt_machine_data *dcfg;
+ unsigned int hw_id;
+ unsigned int hw_rev;
+ const char *name;
+ struct poller_async poller;
+ unsigned int usb_delay;
+};
+
+struct prti6q_rfid_contents {
+ u8 mac[6];
+ char serial[10];
+ u8 cs;
+} __attribute__ ((packed));
+
+#define GPIO_DIP1_FB IMX_GPIO_NR(4, 18)
+#define GPIO_FORCE_ON1 IMX_GPIO_NR(2, 30)
+#define GPIO_ON1_CTRL IMX_GPIO_NR(4, 21)
+#define GPIO_ON2_CTRL IMX_GPIO_NR(4, 22)
+
+static const struct gpio prt_imx6_kvg_gpios[] = {
+ {
+ .gpio = GPIO_DIP1_FB,
+ .flags = GPIOF_IN,
+ .label = "DIP1_FB",
+ },
+ {
+ .gpio = GPIO_FORCE_ON1,
+ .flags = GPIOF_OUT_INIT_HIGH,
+ .label = "FORCE_ON1",
+ },
+ {
+ .gpio = GPIO_ON1_CTRL,
+ .flags = GPIOF_IN,
+ .label = "ON1_CTRL",
+ },
+ {
+ .gpio = GPIO_ON2_CTRL,
+ .flags = GPIOF_IN,
+ .label = "ON2_CTRL",
+ },
+};
+
+static int prt_imx6_read_rfid(struct prt_imx6_priv *priv, void *buf,
+ size_t size)
+{
+ const struct prt_machine_data *dcfg = priv->dcfg;
+ struct device_d *dev = priv->dev;
+ struct i2c_client cl;
+ int ret;
+
+ cl.addr = dcfg->i2c_addr;
+ cl.adapter = i2c_get_adapter(dcfg->i2c_adapter);
+ if (!cl.adapter) {
+ dev_err(dev, "i2c bus not found\n");
+ return -ENODEV;
+ }
+
+ /* 0x6000 user storage in the RFID tag */
+ ret = i2c_read_reg(&cl, 0x6000 | I2C_ADDR_16_BIT, buf, size);
+ if (ret < 0) {
+ dev_err(dev, "Filed to read the RFID: %i\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static u8 prt_imx6_calc_rfid_crc(void *buf, size_t size)
+{
+ unsigned int cs = 0;
+ u8 *dat = buf;
+ int t;
+
+ for (t = 0; t < size - 1; t++) {
+ cs += dat[t];
+ }
+
+ cs ^= 0xff;
+
+ return cs & 0xff;
+
+}
+
+static int prt_imx6_set_mac(struct prt_imx6_priv *priv,
+ struct prti6q_rfid_contents *rfid)
+{
+ struct device_d *dev = priv->dev;
+ struct device_node *node;
+
+ node = of_find_node_by_alias(of_get_root_node(), "ethernet0");
+ if (!node) {
+ dev_err(dev, "Cannot find FEC!\n");
+ return -ENODEV;
+ }
+
+ if (!is_valid_ether_addr(&rfid->mac[0])) {
+ dev_err(dev, "bad MAC addr\n");
+ return -EILSEQ;
+ }
+
+ of_eth_register_ethaddr(node, &rfid->mac[0]);
+
+ return 0;
+}
+
+static int prt_of_fixup_serial(struct device_node *dstroot, void *arg)
+{
+ struct device_node *srcroot = arg;
+ const char *ser;
+ int len;
+
+ ser = of_get_property(srcroot, "serial-number", &len);
+ return of_set_property(dstroot, "serial-number", ser, len, 1);
+}
+
+static void prt_oftree_fixup_serial(const char *serial)
+{
+ struct device_node *root = of_get_root_node();
+
+ of_set_property(root, "serial-number", serial, strlen(serial) + 1, 1);
+ of_register_fixup(prt_of_fixup_serial, root);
+}
+
+static int prt_imx6_set_serial(struct prt_imx6_priv *priv,
+ struct prti6q_rfid_contents *rfid)
+{
+ rfid->serial[9] = 0; /* Failsafe */
+ dev_info(priv->dev, "Serial number: %s\n", rfid->serial);
+ prt_oftree_fixup_serial(rfid->serial);
+
+ return 0;
+}
+
+static int prt_imx6_read_i2c_mac_serial(struct prt_imx6_priv *priv)
+{
+ struct device_d *dev = priv->dev;
+ struct prti6q_rfid_contents rfid;
+ int ret;
+
+ ret = prt_imx6_read_rfid(priv, &rfid, sizeof(rfid));
+ if (ret)
+ return ret;
+
+ if (rfid.cs != prt_imx6_calc_rfid_crc(&rfid, sizeof(rfid))) {
+ dev_err(dev, "RFID: bad checksum!\n");
+ return -EBADMSG;
+ }
+
+ ret = prt_imx6_set_mac(priv, &rfid);
+ if (ret)
+ return ret;
+
+ ret = prt_imx6_set_serial(priv, &rfid);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+#define OTG_PORTSC1 (MX6_OTG_BASE_ADDR+0x184)
+
+static void prt_imx6_check_usb_boot(void *data)
+{
+ struct prt_imx6_priv *priv = data;
+ struct device_d *dev = priv->dev;
+ char *second_word, *bootsrc;
+ unsigned int v;
+ ssize_t size;
+ char buf[16];
+ int fd, ret;
+
+ v = *((unsigned int *)OTG_PORTSC1);
+ if ((v & 0x0c00) == 0) /* LS == SE0 ==> nothing connected */
+ return;
+
+ usb_rescan();
+
+ ret = mkdir("/usb", 0);
+ if (ret) {
+ dev_err(dev, "Cannot mkdir /usb\n");
+ goto exit_usb_boot;
+ }
+
+ ret = mount("/dev/disk0.0", NULL, "usb", NULL);
+ if (ret) {
+ dev_warn(dev, "Filed to mount USB Disk partition with error (%i), trying bare device\n", ret);
+
+ ret = mount("/dev/disk0", NULL, "usb", NULL);
+ if (ret) {
+ dev_err(dev, "USB mount failed!\n");
+ goto exit_usb_boot;
+ }
+ }
+
+ fd = open("/usb/boot_target", O_RDONLY);
+ if (fd < 0) {
+ dev_err(dev, "Can't open /usb/boot_target file\n");
+ ret = fd;
+ goto exit_usb_boot;
+ }
+
+ size = read(fd, buf, sizeof(buf));
+ close(fd);
+ if (size < 0) {
+ ret = size;
+ goto exit_usb_boot;
+ }
+
+ /* length of "vicut1 usb", the shortest possible target */
+ if (size < sizeof("vicut1 usb")) {
+ dev_err(dev, "Invalid boot target file!\n");
+ ret = -EINVAL;
+ goto exit_usb_boot;
+ }
+
+ if (strncmp(buf, priv->name, 6) && strncmp(buf, "prti6qp ", 8)) {
+ dev_err(dev, "Boot target for a different board! (%s %s)\n",
+ buf, priv->name);
+ ret = -EINVAL;
+ goto exit_usb_boot;
+ }
+
+ second_word = strchr(buf, 32);
+ second_word++;
+
+ if (strncmp(second_word, "usb", 3) == 0) {
+ bootsrc = "disk0.0";
+ } else if (strncmp(second_word, "recovery", 8) == 0) {
+ bootsrc = "recovery";
+ } else {
+ dev_err(dev, "Unknown boot target!\n");
+ ret = -ENODEV;
+ goto exit_usb_boot;
+ }
+
+ ret = setenv("global.boot.default", bootsrc);
+ if (ret)
+ goto exit_usb_boot;
+
+ return;
+
+exit_usb_boot:
+ dev_err(dev, "Failed to run usb boot: %i\n", ret);
+
+ return;
+}
+
+static int prt_imx6_env_init(struct prt_imx6_priv *priv)
+{
+ const struct prt_machine_data *dcfg = priv->dcfg;
+ struct device_d *dev = priv->dev;
+ char *delay, *bootsrc;
+ int ret;
+
+ ret = setenv("global.linux.bootargs.base", "consoleblank=0 vt.color=0x00");
+ if (ret)
+ goto exit_env_init;
+
+ if (dcfg->flags & PRT_IMX6_USB_LONG_DELAY)
+ priv->usb_delay = 4;
+ else
+ priv->usb_delay = 1;
+
+ /* the usb_delay value is used for poller_call_async() */
+ delay = basprintf("%d", priv->usb_delay);
+ ret = setenv("global.autoboot_timeout", delay);
+ if (ret)
+ goto exit_env_init;
+
+ if (dcfg->flags & PRT_IMX6_BOOTCHOOSER)
+ bootsrc = "bootchooser";
+ else
+ bootsrc = "mmc2";
+
+ ret = setenv("global.boot.default", bootsrc);
+ if (ret)
+ goto exit_env_init;
+
+ dev_info(dev, "Board specific env init is done\n");
+ return 0;
+
+exit_env_init:
+ dev_err(dev, "Failed to set env: %i\n", ret);
+
+ return ret;
+}
+
+static int prt_imx6_bbu(struct prt_imx6_priv *priv)
+{
+ const struct prt_machine_data *dcfg = priv->dcfg;
+ u32 emmc_flags = 0;
+ int ret;
+
+ if (dcfg->flags & PRT_IMX6_BOOTSRC_SPI_NOR) {
+ ret = imx6_bbu_internal_spi_i2c_register_handler("SPI", "/dev/m25p0.barebox",
+ BBU_HANDLER_FLAG_DEFAULT);
+ if (ret)
+ goto exit_bbu;
+ } else {
+ emmc_flags = BBU_HANDLER_FLAG_DEFAULT;
+ }
+
+ ret = imx6_bbu_internal_mmcboot_register_handler("eMMC", "/dev/mmc2",
+ emmc_flags);
+ if (ret)
+ goto exit_bbu;
+
+ ret = imx6_bbu_internal_mmc_register_handler("SD", "/dev/mmc0", 0);
+ if (ret)
+ goto exit_bbu;
+
+ return 0;
+exit_bbu:
+ dev_err(priv->dev, "Failed to register bbu: %i\n", ret);
+ return ret;
+}
+
+static int prt_imx6_devices_init(void)
+{
+ struct prt_imx6_priv *priv = prt_priv;
+ int ret;
+
+ if (!priv)
+ return 0;
+
+ if (priv->dcfg->init) {
+ ret = priv->dcfg->init(priv);
+ if (ret)
+ return ret;
+ }
+
+ ret = prt_imx6_bbu(priv);
+ if (ret)
+ return ret;
+
+ ret = prt_imx6_read_i2c_mac_serial(priv);
+ if (ret)
+ return ret;
+
+ ret = prt_imx6_env_init(priv);
+ if (ret)
+ return ret;
+
+ ret = poller_async_register(&priv->poller, "usb-boot");
+ if (ret) {
+ dev_err(priv->dev, "can't setup poller\n");
+ return ret;
+ }
+
+ poller_call_async(&priv->poller, priv->usb_delay * SECOND,
+ &prt_imx6_check_usb_boot, priv);
+
+ return 0;
+}
+late_initcall(prt_imx6_devices_init);
+
+static int prt_imx6_init_kvg_set_ctrl(struct prt_imx6_priv *priv, bool val)
+{
+ int ret;
+
+ ret = gpio_direction_output(GPIO_ON1_CTRL, val);
+ if (ret)
+ return ret;
+
+ ret = gpio_direction_output(GPIO_ON2_CTRL, val);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int prt_imx6_yaco_set_kvg_power_mode(struct prt_imx6_priv *priv,
+ char *serial)
+{
+ static const char command[] = "{\"command\":\"mode\",\"value\":\"kvg\",\"on2\":true}";
+ struct device_d *dev = priv->dev;
+ struct console_device *yccon;
+ int ret;
+
+ yccon = of_console_get_by_alias(serial);
+ if (!yccon) {
+ dev_dbg(dev, "Cant find the %s node, try later\n", serial);
+ return -EPROBE_DEFER;
+ }
+
+ ret = console_set_baudrate(yccon, 115200);
+ if (ret)
+ goto exit_yaco_set_kvg_power_mode;
+
+ yccon->puts(yccon, command, sizeof(command));
+
+ dev_info(dev, "Send YaCO power init sequence to the %s\n", serial);
+ return 0;
+
+exit_yaco_set_kvg_power_mode:
+ dev_err(dev, "Failed to set YaCO pw mode: %i", ret);
+
+ return ret;
+}
+
+static int prt_imx6_init_kvg_power(struct prt_imx6_priv *priv,
+ enum prt_imx6_kvg_pw_mode pw_mode)
+{
+ const char *mode;
+ int ret;
+
+ ret = gpio_request_array(prt_imx6_kvg_gpios,
+ ARRAY_SIZE(prt_imx6_kvg_gpios));
+ if (ret)
+ goto exit_init_kvg_vicut;
+
+ mdelay(1);
+
+ if (!gpio_get_value(GPIO_DIP1_FB))
+ pw_mode = PW_MODE_KUBOTA;
+
+ switch (pw_mode) {
+ case PW_MODE_KVG_WITH_YACO:
+ mode = "KVG (with YaCO)";
+
+ /* GPIO_ON1_CTRL and GPIO_ON2_CTRL are N.C. on the SoC for
+ * older revisions */
+
+ /* Inform YaCO of power mode */
+ ret = prt_imx6_yaco_set_kvg_power_mode(priv, "serial0");
+ break;
+ case PW_MODE_KVG_NEW:
+ mode = "KVG (new)";
+
+ ret = prt_imx6_init_kvg_set_ctrl(priv, true);
+ if (ret)
+ goto exit_init_kvg_vicut;
+ break;
+ case PW_MODE_KUBOTA:
+ mode = "Kubota";
+ ret = prt_imx6_init_kvg_set_ctrl(priv, false);
+ if (ret)
+ goto exit_init_kvg_vicut;
+ break;
+ default:
+ ret = -ENODEV;
+ goto exit_init_kvg_vicut;
+ }
+
+ dev_info(priv->dev, "Power mode: %s\n", mode);
+
+ return 0;
+
+exit_init_kvg_vicut:
+ dev_err(priv->dev, "KvG power init failed: %i\n", ret);
+
+ return ret;
+}
+
+static int prt_imx6_init_victgo(struct prt_imx6_priv *priv)
+{
+ int ret = 0;
+
+ /* Bit 1 of HW-REV is pulled low by 2k2, but must be high on some
+ * revisions
+ */
+ if (priv->hw_rev & 2) {
+ ret = gpio_direction_output(IMX_GPIO_NR(2, 9), 1);
+ if (ret) {
+ dev_err(priv->dev, "Failed to set gpio up\n");
+ return ret;
+ }
+ }
+
+ return prt_imx6_init_kvg_power(priv, PW_MODE_KVG_NEW);
+}
+
+static int prt_imx6_init_kvg_new(struct prt_imx6_priv *priv)
+{
+ return prt_imx6_init_kvg_power(priv, PW_MODE_KVG_NEW);
+}
+
+static int prt_imx6_init_kvg_yaco(struct prt_imx6_priv *priv)
+{
+ return prt_imx6_init_kvg_power(priv, PW_MODE_KVG_WITH_YACO);
+}
+
+static int prt_imx6_rfid_fixup(struct prt_imx6_priv *priv,
+ struct device_node *root)
+{
+ const struct prt_machine_data *dcfg = priv->dcfg;
+ struct device_node *node, *i2c_node;
+ char *eeprom_node_name, *alias;
+ int na, ns, len = 0;
+ int ret;
+ u8 *tmp;
+
+ alias = basprintf("i2c%d", dcfg->i2c_adapter);
+ if (!alias) {
+ ret = -ENOMEM;
+ goto exit_error;
+ }
+
+ i2c_node = of_find_node_by_alias(root, alias);
+ if (!i2c_node) {
+ dev_err(priv->dev, "Unsupported i2c adapter\n");
+ ret = -ENODEV;
+ goto free_alias;
+ }
+
+ eeprom_node_name = basprintf("/eeprom@%x", dcfg->i2c_addr);
+ if (!eeprom_node_name) {
+ ret = -ENOMEM;
+ goto free_alias;
+ }
+
+ node = of_create_node(i2c_node, eeprom_node_name);
+ if (!node) {
+ dev_err(priv->dev, "Failed to create node %s\n",
+ eeprom_node_name);
+ ret = -ENOMEM;
+ goto free_eeprom;
+ }
+
+ ret = of_property_write_string(node, "compatible", "atmel,24c256");
+ if (ret)
+ goto free_eeprom;
+
+ na = of_n_addr_cells(node);
+ ns = of_n_size_cells(node);
+ tmp = xzalloc((na + ns) * 4);
+
+ of_write_number(tmp + len, dcfg->i2c_addr, na);
+ len += na * 4;
+ of_write_number(tmp + len, 0, ns);
+ len += ns * 4;
+
+ ret = of_set_property(node, "reg", tmp, len, 1);
+ kfree(tmp);
+ if (ret)
+ goto free_eeprom;
+
+ return 0;
+free_eeprom:
+ kfree(eeprom_node_name);
+free_alias:
+ kfree(alias);
+exit_error:
+ dev_err(priv->dev, "Failed to apply fixup: %i\n", ret);
+ return ret;
+}
+
+static int prt_imx6_of_fixup(struct device_node *root, void *data)
+{
+ struct prt_imx6_priv *priv = data;
+ int ret;
+
+ if (!root) {
+ dev_err(priv->dev, "Unable to find the root node\n");
+ return -ENODEV;
+ }
+
+ ret = prt_imx6_rfid_fixup(priv, root);
+ if (ret)
+ goto exit_of_fixups;
+
+ return 0;
+exit_of_fixups:
+ dev_err(priv->dev, "Failed to apply OF fixups: %i\n", ret);
+ return ret;
+}
+
+static int prt_imx6_get_id(struct prt_imx6_priv *priv)
+{
+ struct gpio gpios_type[] = GPIO_HW_TYPE_ID;
+ struct gpio gpios_rev[] = GPIO_HW_REV_ID;
+ int ret;
+
+ ret = gpio_array_to_id(gpios_type, ARRAY_SIZE(gpios_type), &priv->hw_id);
+ if (ret)
+ goto exit_get_id;
+
+ ret = gpio_array_to_id(gpios_rev, ARRAY_SIZE(gpios_rev), &priv->hw_rev);
+ if (ret)
+ goto exit_get_id;
+
+ return 0;
+exit_get_id:
+ dev_err(priv->dev, "Failed to read gpio ID: %i\n", ret);
+ return ret;
+}
+
+static int prt_imx6_get_dcfg(struct prt_imx6_priv *priv)
+{
+ const struct prt_machine_data *dcfg, *found = NULL;
+ int ret;
+
+ dcfg = of_device_get_match_data(priv->dev);
+ if (!dcfg) {
+ ret = -EINVAL;
+ goto exit_get_dcfg;
+ }
+
+ for (; dcfg->hw_id != UINT_MAX; dcfg++) {
+ if (dcfg->hw_id != priv->hw_id)
+ continue;
+ if (dcfg->hw_rev > priv->hw_rev)
+ break;
+ found = dcfg;
+ }
+
+ if (!found) {
+ ret = -ENODEV;
+ goto exit_get_dcfg;
+ }
+
+ priv->dcfg = found;
+
+ return 0;
+exit_get_dcfg:
+ dev_err(priv->dev, "Failed to get dcfg: %i\n", ret);
+ return ret;
+}
+
+static int prt_imx6_probe(struct device_d *dev)
+{
+ struct prt_imx6_priv *priv;
+ const char *name, *ptr;
+ struct param_d *p;
+ int ret;
+
+ priv = kzalloc(sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->dev = dev;
+ name = of_device_get_match_compatible(priv->dev);
+ ptr = strchr(name, ',');
+ priv->name = ptr ? ptr + 1 : name;
+
+ pr_info("Detected machine type: %s\n", priv->name);
+
+ ret = prt_imx6_get_id(priv);
+ if (ret)
+ goto free_priv;
+
+ pr_info(" HW type: %d\n", priv->hw_id);
+ pr_info(" HW revision: %d\n", priv->hw_rev);
+
+ ret = prt_imx6_get_dcfg(priv);
+ if (ret)
+ goto free_priv;
+
+ p = dev_add_param_uint32_ro(dev, "boardrev", &priv->hw_rev, "%u");
+ if (IS_ERR(p)) {
+ ret = PTR_ERR(p);
+ goto free_priv;
+ }
+
+ p = dev_add_param_uint32_ro(dev, "boardid", &priv->hw_id, "%u");
+ if (IS_ERR(p)) {
+ ret = PTR_ERR(p);
+ goto free_priv;
+ }
+
+ ret = prt_imx6_of_fixup(of_get_root_node(), priv);
+ if (ret)
+ goto free_priv;
+
+ ret = of_register_fixup(prt_imx6_of_fixup, priv);
+ if (ret) {
+ dev_err(dev, "Failed to register fixup\n");
+ goto free_priv;
+ }
+
+ prt_priv = priv;
+
+ return 0;
+free_priv:
+ kfree(priv);
+ return ret;
+}
+
+static const struct prt_machine_data prt_imx6_cfg_alti6p[] = {
+ {
+ .hw_id = HW_TYPE_ALTI6P,
+ .hw_rev = 0,
+ .i2c_addr = 0x51,
+ .i2c_adapter = 0,
+ .flags = PRT_IMX6_BOOTSRC_EMMC,
+ }, {
+ .hw_id = UINT_MAX
+ },
+};
+
+static const struct prt_machine_data prt_imx6_cfg_victgo[] = {
+ {
+ .hw_id = HW_TYPE_VICTGO,
+ .hw_rev = 0,
+ .i2c_addr = 0x51,
+ .i2c_adapter = 0,
+ .init = prt_imx6_init_victgo,
+ .flags = PRT_IMX6_BOOTSRC_SPI_NOR,
+ }, {
+ .hw_id = UINT_MAX
+ },
+};
+
+static const struct prt_machine_data prt_imx6_cfg_vicut1[] = {
+ {
+ .hw_id = HW_TYPE_VICUT1,
+ .hw_rev = 0,
+ .i2c_addr = 0x50,
+ .i2c_adapter = 1,
+ .flags = PRT_IMX6_BOOTSRC_SPI_NOR,
+ }, {
+ .hw_id = HW_TYPE_VICUT1,
+ .hw_rev = 1,
+ .i2c_addr = 0x51,
+ .i2c_adapter = 0,
+ .init = prt_imx6_init_kvg_yaco,
+ .flags = PRT_IMX6_BOOTSRC_SPI_NOR,
+ }, {
+ .hw_id = HW_TYPE_VICUT2,
+ .hw_rev = 1,
+ .i2c_addr = 0x51,
+ .i2c_adapter = 0,
+ .init = prt_imx6_init_kvg_new,
+ .flags = PRT_IMX6_BOOTSRC_SPI_NOR,
+ }, {
+ .hw_id = UINT_MAX
+ },
+};
+
+static const struct prt_machine_data prt_imx6_cfg_vicut1q[] = {
+ {
+ .hw_id = HW_TYPE_VICUT1,
+ .hw_rev = 0,
+ .i2c_addr = 0x50,
+ .i2c_adapter = 1,
+ .flags = PRT_IMX6_BOOTSRC_SPI_NOR,
+ }, {
+ .hw_id = HW_TYPE_VICUT1,
+ .hw_rev = 1,
+ .i2c_addr = 0x51,
+ .i2c_adapter = 0,
+ .init = prt_imx6_init_kvg_yaco,
+ .flags = PRT_IMX6_BOOTSRC_SPI_NOR,
+ }, {
+ .hw_id = HW_TYPE_VICUT2,
+ .hw_rev = 0,
+ .i2c_addr = 0x51,
+ .i2c_adapter = 0,
+ .init = prt_imx6_init_kvg_yaco,
+ .flags = PRT_IMX6_BOOTSRC_SPI_NOR,
+ }, {
+ .hw_id = HW_TYPE_VICUT2,
+ .hw_rev = 1,
+ .i2c_addr = 0x51,
+ .i2c_adapter = 0,
+ .init = prt_imx6_init_kvg_new,
+ .flags = PRT_IMX6_BOOTSRC_SPI_NOR,
+ }, {
+ .hw_id = UINT_MAX
+ },
+};
+
+static const struct prt_machine_data prt_imx6_cfg_vicutp[] = {
+ {
+ .hw_id = HW_TYPE_VICUT2,
+ .hw_rev = 1,
+ .i2c_addr = 0x51,
+ .i2c_adapter = 0,
+ .init = prt_imx6_init_kvg_new,
+ .flags = PRT_IMX6_BOOTSRC_SPI_NOR,
+ }, {
+ .hw_id = UINT_MAX
+ },
+};
+
+static const struct prt_machine_data prt_imx6_cfg_lanmcu[] = {
+ {
+ .hw_id = HW_TYPE_LANMCU,
+ .hw_rev = 0,
+ .i2c_addr = 0x51,
+ .i2c_adapter = 0,
+ .flags = PRT_IMX6_BOOTSRC_EMMC | PRT_IMX6_BOOTCHOOSER,
+ }, {
+ .hw_id = UINT_MAX
+ },
+};
+
+static const struct prt_machine_data prt_imx6_cfg_plybas[] = {
+ {
+ .hw_id = HW_TYPE_PLYBAS,
+ .hw_rev = 0,
+ .i2c_addr = 0x51,
+ .i2c_adapter = 0,
+ .flags = PRT_IMX6_BOOTSRC_SPI_NOR | PRT_IMX6_USB_LONG_DELAY,
+ }, {
+ .hw_id = UINT_MAX
+ },
+};
+
+static const struct prt_machine_data prt_imx6_cfg_plym2m[] = {
+ {
+ .hw_id = HW_TYPE_PLYM2M,
+ .hw_rev = 0,
+ .i2c_addr = 0x51,
+ .i2c_adapter = 0,
+ .flags = PRT_IMX6_BOOTSRC_SPI_NOR | PRT_IMX6_USB_LONG_DELAY,
+ }, {
+ .hw_id = UINT_MAX
+ },
+};
+
+static const struct prt_machine_data prt_imx6_cfg_prti6g[] = {
+ {
+ .hw_id = HW_TYPE_PRTI6G,
+ .hw_rev = 0,
+ .i2c_addr = 0x51,
+ .i2c_adapter = 0,
+ .flags = PRT_IMX6_BOOTSRC_EMMC,
+ }, {
+ .hw_id = UINT_MAX
+ },
+};
+
+static const struct prt_machine_data prt_imx6_cfg_prti6q[] = {
+ {
+ .hw_id = HW_TYPE_PRTI6Q,
+ .hw_rev = 0,
+ .i2c_addr = 0x51,
+ .i2c_adapter = 2,
+ .flags = PRT_IMX6_BOOTSRC_SPI_NOR,
+ }, {
+ .hw_id = HW_TYPE_PRTI6Q,
+ .hw_rev = 1,
+ .i2c_addr = 0x51,
+ .i2c_adapter = 0,
+ .flags = PRT_IMX6_BOOTSRC_SPI_NOR,
+ }, {
+ .hw_id = UINT_MAX
+ },
+};
+
+static const struct prt_machine_data prt_imx6_cfg_prtmvt[] = {
+ {
+ .hw_id = HW_TYPE_PRTMVT,
+ .hw_rev = 0,
+ .i2c_addr = 0x51,
+ .i2c_adapter = 0,
+ .flags = PRT_IMX6_BOOTSRC_SPI_NOR,
+ }, {
+ .hw_id = UINT_MAX
+ },
+};
+
+static const struct prt_machine_data prt_imx6_cfg_prtrvt[] = {
+ {
+ .hw_id = HW_TYPE_PRTRVT,
+ .hw_rev = 0,
+ .i2c_addr = 0x51,
+ .i2c_adapter = 0,
+ .flags = PRT_IMX6_BOOTSRC_SPI_NOR,
+ }, {
+ .hw_id = UINT_MAX
+ },
+};
+
+static const struct prt_machine_data prt_imx6_cfg_prtvt7[] = {
+ {
+ .hw_id = HW_TYPE_PRTVT7,
+ .hw_rev = 0,
+ .i2c_addr = 0x51,
+ .i2c_adapter = 0,
+ .flags = PRT_IMX6_BOOTSRC_EMMC | PRT_IMX6_BOOTCHOOSER,
+ }, {
+ .hw_id = UINT_MAX
+ },
+};
+
+static const struct prt_machine_data prt_imx6_cfg_prtwd2[] = {
+ {
+ .hw_id = HW_TYPE_PRTWD2,
+ .hw_rev = 0,
+ .i2c_addr = 0x51,
+ .i2c_adapter = 0,
+ .flags = PRT_IMX6_BOOTSRC_EMMC,
+ }, {
+ .hw_id = UINT_MAX
+ },
+};
+
+static const struct prt_machine_data prt_imx6_cfg_prtwd3[] = {
+ {
+ .hw_id = HW_TYPE_PRTWD2,
+ .hw_rev = 2,
+ .i2c_addr = 0x51,
+ .i2c_adapter = 0,
+ .flags = PRT_IMX6_BOOTSRC_EMMC,
+ }, {
+ .hw_id = UINT_MAX
+ },
+};
+
+static const struct of_device_id prt_imx6_of_match[] = {
+ { .compatible = "alt,alti6p", .data = &prt_imx6_cfg_alti6p },
+ { .compatible = "kvg,victgo", .data = &prt_imx6_cfg_victgo },
+ { .compatible = "kvg,vicut1", .data = &prt_imx6_cfg_vicut1 },
+ { .compatible = "kvg,vicut1q", .data = &prt_imx6_cfg_vicut1q },
+ { .compatible = "kvg,vicutp", .data = &prt_imx6_cfg_vicutp },
+ { .compatible = "lan,lanmcu", .data = &prt_imx6_cfg_lanmcu },
+ { .compatible = "ply,plybas", .data = &prt_imx6_cfg_plybas },
+ { .compatible = "ply,plym2m", .data = &prt_imx6_cfg_plym2m },
+ { .compatible = "prt,prti6g", .data = &prt_imx6_cfg_prti6g },
+ { .compatible = "prt,prti6q", .data = &prt_imx6_cfg_prti6q },
+ { .compatible = "prt,prtmvt", .data = &prt_imx6_cfg_prtmvt },
+ { .compatible = "prt,prtrvt", .data = &prt_imx6_cfg_prtrvt },
+ { .compatible = "prt,prtvt7", .data = &prt_imx6_cfg_prtvt7 },
+ { .compatible = "prt,prtwd2", .data = &prt_imx6_cfg_prtwd2 },
+ { .compatible = "prt,prtwd3", .data = &prt_imx6_cfg_prtwd3 },
+ { /* sentinel */ },
+};
+
+static struct driver_d prt_imx6_board_driver = {
+ .name = "board-protonic-imx6",
+ .probe = prt_imx6_probe,
+ .of_compatible = DRV_OF_COMPAT(prt_imx6_of_match),
+};
+postcore_platform_driver(prt_imx6_board_driver);
--
2.28.0
More information about the barebox
mailing list