[PATCH 03/24] arm: at91: add at91sam926x_board_init.h
Sam Ravnborg
sam at ravnborg.org
Wed Dec 27 12:50:12 PST 2017
To prepare moving reset code to board code create at91sam926x_board_init.h.
at91sam926x_board_init.h is a copy of at91sam926x_lowlevel_init.c
with a few changes:
- We no longer call board code from this function
- The struct is renamed to avoid name clashes
- Function renamed to better match the prurpose
This file allows board code to include at91sam926x_board_init.h
and use the init functions in their init code.
Users must select AT91SAM926X_BOARD_INIT
Signed-off-by: Sam Ravnborg <sam at ravnborg.org>
---
.../include/mach/at91sam926x_board_init.h | 231 +++++++++++++++++++++
1 file changed, 231 insertions(+)
create mode 100644 arch/arm/mach-at91/include/mach/at91sam926x_board_init.h
diff --git a/arch/arm/mach-at91/include/mach/at91sam926x_board_init.h b/arch/arm/mach-at91/include/mach/at91sam926x_board_init.h
new file mode 100644
index 000000000..1c58d2f25
--- /dev/null
+++ b/arch/arm/mach-at91/include/mach/at91sam926x_board_init.h
@@ -0,0 +1,231 @@
+#ifndef __AT91SAM926X_BOARD_INIT_H__
+#define __AT91SAM926X_BOARD_INIT_H__
+/*
+ * Copyright (C) 2008 Ronetix Ilko Iliev (www.ronetix.at)
+ * Copyright (C) 2009-2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
+ *
+ * Under GPLv2
+ */
+
+#include <common.h>
+#include <init.h>
+
+#include <mach/at91sam9_sdramc.h>
+#include <mach/at91sam9_smc.h>
+#include <mach/at91_rstc.h>
+#include <mach/at91_pio.h>
+#include <mach/at91_pmc.h>
+#include <mach/at91_wdt.h>
+#include <mach/hardware.h>
+#include <mach/gpio.h>
+
+struct at91sam926x_board_cfg {
+ /* SoC specific */
+ void __iomem *pio;
+ void __iomem *sdramc;
+ u32 ebi_pio_is_peripha;
+ u32 matrix_csa;
+
+ /* board specific */
+ u32 wdt_mr;
+ u32 ebi_pio_pdr;
+ u32 ebi_pio_ppudr;
+ u32 ebi_csa;
+ u32 smc_cs;
+ u32 smc_mode;
+ u32 smc_cycle;
+ u32 smc_pulse;
+ u32 smc_setup;
+ u32 pmc_mor;
+ u32 pmc_pllar;
+ u32 pmc_mckr1;
+ u32 pmc_mckr2;
+ u32 sdrc_cr;
+ u32 sdrc_tr1;
+ u32 sdrc_mdr;
+ u32 sdrc_tr2;
+ u32 rstc_rmr;
+};
+
+
+static void __always_inline access_sdram(void)
+{
+ writel(0x00000000, AT91_SDRAM_BASE);
+}
+
+static void __always_inline pmc_check_mckrdy(void)
+{
+ u32 r;
+
+ do {
+ r = at91_pmc_read(AT91_PMC_SR);
+ } while (!(r & AT91_PMC_MCKRDY));
+}
+
+static int __always_inline running_in_sram(void)
+{
+ u32 addr = get_pc();
+
+ addr >>= 28;
+ return addr == 0;
+}
+
+#define at91_sdramc_read(field) \
+ __raw_readl(cfg->sdramc + field)
+
+#define at91_sdramc_write(field, value) \
+ __raw_writel(value, cfg->sdramc + field)
+
+static void __always_inline __bare_init at91sam926x_sdramc_init(struct at91sam926x_board_cfg *cfg)
+{
+ u32 r;
+ int i;
+ int in_sram = running_in_sram();
+
+ /*
+ * SDRAMC Check if Refresh Timer Counter is already initialized
+ */
+ r = at91_sdramc_read(AT91_SDRAMC_TR);
+ if (r && !in_sram)
+ return;
+
+ /* SDRAMC_MR : Normal Mode */
+ at91_sdramc_write(AT91_SDRAMC_MR, AT91_SDRAMC_MODE_NORMAL);
+
+ /* SDRAMC_TR - Refresh Timer register */
+ at91_sdramc_write(AT91_SDRAMC_TR, cfg->sdrc_tr1);
+
+ /* SDRAMC_CR - Configuration register*/
+ at91_sdramc_write(AT91_SDRAMC_CR, cfg->sdrc_cr);
+
+ /* Memory Device Type */
+ at91_sdramc_write(AT91_SDRAMC_MDR, cfg->sdrc_mdr);
+
+ /* SDRAMC_MR : Precharge All */
+ at91_sdramc_write(AT91_SDRAMC_MR, AT91_SDRAMC_MODE_PRECHARGE);
+
+ /* access SDRAM */
+ access_sdram();
+
+ /* SDRAMC_MR : refresh */
+ at91_sdramc_write(AT91_SDRAMC_MR, AT91_SDRAMC_MODE_REFRESH);
+
+ /* access SDRAM 8 times */
+ for (i = 0; i < 8; i++)
+ access_sdram();
+
+ /* SDRAMC_MR : Load Mode Register */
+ at91_sdramc_write(AT91_SDRAMC_MR, AT91_SDRAMC_MODE_LMR);
+
+ /* access SDRAM */
+ access_sdram();
+
+ /* SDRAMC_MR : Normal Mode */
+ at91_sdramc_write(AT91_SDRAMC_MR, AT91_SDRAMC_MODE_NORMAL);
+
+ /* access SDRAM */
+ access_sdram();
+
+ /* SDRAMC_TR : Refresh Timer Counter */
+ at91_sdramc_write(AT91_SDRAMC_TR, cfg->sdrc_tr2);
+
+ /* access SDRAM */
+ access_sdram();
+}
+
+#if !defined(CONFIG_AT91SAM926X_BOARD_INIT)
+/*
+ * Empty function if the board do not use this.
+ * Board code can call this, and let Kconfig select decide if
+ * the board uses at91sam926x_board_init()
+ */
+static void __always_inline __bare_init at91sam926x_board_init(struct at91sam926x_board_cfg *cfg)
+{
+}
+#else
+static void __always_inline __bare_init at91sam926x_board_init(struct at91sam926x_board_cfg *cfg)
+{
+ u32 r;
+ int in_sram = running_in_sram();
+
+ __raw_writel(cfg->wdt_mr, AT91_BASE_WDT + AT91_WDT_MR);
+
+ /* configure PIOx as EBI0 D[16-31] */
+ at91_mux_gpio_disable(cfg->pio, cfg->ebi_pio_pdr);
+ at91_mux_set_pullup(cfg->pio, cfg->ebi_pio_ppudr, true);
+ if (cfg->ebi_pio_is_peripha)
+ at91_mux_set_A_periph(cfg->pio, cfg->ebi_pio_ppudr);
+
+ at91_sys_write(cfg->matrix_csa, cfg->ebi_csa);
+
+ /* flash */
+ at91_smc_write(cfg->smc_cs, AT91_SAM9_SMC_MODE, cfg->smc_mode);
+
+ at91_smc_write(cfg->smc_cs, AT91_SMC_CYCLE, cfg->smc_cycle);
+
+ at91_smc_write(cfg->smc_cs, AT91_SMC_PULSE, cfg->smc_pulse);
+
+ at91_smc_write(cfg->smc_cs, AT91_SMC_SETUP, cfg->smc_setup);
+
+ /*
+ * PMC Check if the PLL is already initialized
+ */
+ r = at91_pmc_read(AT91_PMC_MCKR);
+ if (r & AT91_PMC_CSS && !in_sram)
+ return;
+
+ /*
+ * Enable the Main Oscillator
+ */
+ at91_pmc_write(AT91_CKGR_MOR, cfg->pmc_mor);
+
+ do {
+ r = at91_pmc_read(AT91_PMC_SR);
+ } while (!(r & AT91_PMC_MOSCS));
+
+ /*
+ * PLLAR: x MHz for PCK
+ */
+ at91_pmc_write(AT91_CKGR_PLLAR, cfg->pmc_pllar);
+
+ do {
+ r = at91_pmc_read(AT91_PMC_SR);
+ } while (!(r & AT91_PMC_LOCKA));
+
+ /*
+ * PCK/x = MCK Master Clock from SLOW
+ */
+ at91_pmc_write(AT91_PMC_MCKR, cfg->pmc_mckr1);
+
+ pmc_check_mckrdy();
+
+ /*
+ * PCK/x = MCK Master Clock from PLLA
+ */
+ at91_pmc_write(AT91_PMC_MCKR, cfg->pmc_mckr2);
+
+ pmc_check_mckrdy();
+
+ /*
+ * Init SDRAM
+ */
+ at91sam926x_sdramc_init(cfg);
+
+ /* User reset enable*/
+ at91_sys_write(AT91_RSTC_MR, cfg->rstc_rmr);
+
+#ifdef CONFIG_SYS_MATRIX_MCFG_REMAP
+ /* MATRIX_MCFG - REMAP all masters */
+ at91_sys_write(AT91_MATRIX_MCFG0, 0x1FF);
+#endif
+ /*
+ * When boot from external boot
+ * we need to enable mck and ohter clock
+ * so enable all of them
+ * We will shutdown what we don't need later
+ */
+ at91_pmc_write(AT91_PMC_PCER, 0xffffffff);
+}
+#endif /* CONFIG_AT91SAM926X_BOARD_INIT */
+
+#endif /* __AT91SAM926X_BOARD_INIT_H__ */
--
2.12.0
More information about the barebox
mailing list