[PATCH 2/4] AT91: move have_intensity_bit into board setup

Jean-Christophe PLAGNIOL-VILLARD plagnioj at jcrosoft.com
Tue Sep 3 11:31:48 EDT 2013


On 09:34 Tue 03 Sep     , Darren Garnier wrote:
> 
> On Sep 3, 2013, at 7:39 AM, Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com> wrote:
> 
> > On 22:22 Mon 02 Sep     , Darren Garnier wrote:
> >> Signed-off-by: Darren Garnier <dgarnier at reinrag.net>
> > \why this is soc specific
> 
> Yes, the option is probably soc specific, but in the 9261 soc, we actually have 2 cpus. Both the 9261 and 9g10.
> One of the few differences between these pin compatible chips is the way the LCD peripheral is wired.
> 
> My board has 2 varieties out in the wild.. one with the 9261 and the other with the 9g10 and because of the
> way they are wired, the "intensity bit" is only appropriate to the 9261 cpu board.  Since you can't change this setting easily after you pass it off
> to at91_add_device_lcdc, it's important that it only be set in the board file.
> 

I need to check the datasheet but I'm enarly sure this is not board specific
but SoC

> 
> > 
> > Best Regards,
> > J.
> >> ---
> >> arch/arm/boards/at91sam9261ek/init.c     | 2 ++
> >> arch/arm/mach-at91/at91sam9261_devices.c | 2 --
> >> 2 files changed, 2 insertions(+), 2 deletions(-)
> >> 
> >> diff --git a/arch/arm/boards/at91sam9261ek/init.c b/arch/arm/boards/at91sam9261ek/init.c
> >> index 00fc745..b420a48 100644
> >> --- a/arch/arm/boards/at91sam9261ek/init.c
> >> +++ b/arch/arm/boards/at91sam9261ek/init.c
> >> @@ -223,6 +223,8 @@ static void ek_add_device_lcdc(void)
> >> 
> >> 	if (machine_is_at91sam9g10ek())
> >> 		ek_lcdc_data.lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB;
> >> +	else
> >> +		ek_lcdc_data.has_intensity_bit = true;
> >> 
> >> 	at91_add_device_lcdc(&ek_lcdc_data);
> >> }
> >> diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
> >> index b522afb..ba52e56 100644
> >> --- a/arch/arm/mach-at91/at91sam9261_devices.c
> >> +++ b/arch/arm/mach-at91/at91sam9261_devices.c
> >> @@ -218,8 +218,6 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_platform_data *data)
> >> {
> >> 	BUG_ON(!data);
> >> 
> >> -	data->have_intensity_bit = true;
> >> -
> >> #if defined(CONFIG_FB_ATMEL_STN)
> >> 	at91_set_A_periph(AT91_PIN_PB0, 0);	/* LCDVSYNC */
> >> 	at91_set_A_periph(AT91_PIN_PB1, 0);	/* LCDHSYNC */
> >> -- 
> >> 1.8.3.1
> >> 
> >> 
> >> 
> >> _______________________________________________
> >> barebox mailing list
> >> barebox at lists.infradead.org
> >> http://lists.infradead.org/mailman/listinfo/barebox
> 



More information about the barebox mailing list