Unable to Boot from NAND on Mini2440

[Vikram Narayanan]

Hello,

I followed the instructions here
<http://barebox.org/documentation/barebox-2011.04.0/mini2440.html>

After writing to NAND, I switched the boot mode to NAND and did a reset. 
Nothing comes up on the prompt. I tried to verify the 'write', by a 
'nand_boot_test'. That works. Please find the log below. I'm on the 
latest master.

--- start log ---
Supervivi> go 0x31000000
go to 0x31000000
   argument 0 = 0x00000000
   argument 1 = 0x00000000
   argument 2 = 0x00000000
   argument 3 = 0x00000000


barebox 2013.05.0-00126-g19bc427 #4 Sat May 18 15:53:01 IST 2013


Board: Mini 2440
nand: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 
8-bit), page size: 2048, OOB size: 64
dm9000 dm90000: Found DM9000E at i/o: 0x20000300
mdio_bus: miibus0: probed
s3c_mci s3c_mci0: registered as s3c_mci0
malloc space: 0x31bf8000 -> 0x31ff7fff (size 4 MiB)
refclk:    12000 kHz
mpll:     405000 kHz
upll:      48000 kHz
fclk:     405000 kHz
hclk:     101250 kHz
pclk:      50625 kHz
SDRAM1:   CL4 at 101MHz
SDRAM2:   CL4 at 101MHz
envfs: wrong magic on /dev/env0
no valid environment found on /dev/env0. Using default environment
running /env/bin/init...
set parameter: Invalid argument

Hit any key to stop autoboot:  3
mini2440:/ eth0.ipaddr=192.168.1.240 

mini2440:/ eth0.netmask=255.255.255.0
mini2440:/ eth0.serverip=192.168.1.14
mini2440:/ erase /dev/nand0.barebox.bb
mini2440:/ tftp barebox.bin /dev/nand0.barebox.bb
warning: No MAC address set. Using random address F2:08:F4:9F:14:99
100Mbps full duplex link detected
         ###############
mini2440:/ nand_boot_test 0x32000000 0x40000
mini2440:/ go 0x32000000
## Starting application at 0x32000000 ...


barebox 2013.05.0-00126-g19bc427 #4 Sat May 18 15:53:01 IST 2013


Board: Mini 2440
nand: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 
8-bit), page size: 2048, OOB size: 64
dm9000 dm90000: Found DM9000E at i/o: 0x20000300
mdio_bus: miibus0: probed
s3c_mci s3c_mci0: registered as s3c_mci0
malloc space: 0x31bf8000 -> 0x31ff7fff (size 4 MiB)
refclk:    12000 kHz
mpll:     405000 kHz
upll:      48000 kHz
fclk:     405000 kHz
hclk:     101250 kHz
pclk:      50625 kHz
SDRAM1:   CL4 at 101MHz
SDRAM2:   CL4 at 101MHz
envfs: wrong magic on /dev/env0
no valid environment found on /dev/env0. Using default environment
running /env/bin/init...
set parameter: Invalid argument

Hit any key to stop autoboot:  3
mini2440:/

--- end log ----

Any idea on what goes wrong?

Thanks,
Vikram