[PATCH v3] ARM: at91: Add Telit EVK-PRO3 board support
Fabio Porcedda
fabio.porcedda at gmail.com
Thu Jan 24 09:42:14 EST 2013
http://www.telit.com
Based on at91sam9260ek board support.
Signed-off-by: Fabio Porcedda <fabio.porcedda at gmail.com>
---
v3:
- add dfu support
- init.c: reduced bootstrap size
- init.c: moved istructions from evk_add_device_nand function to the struct
- init.c: remove blank line
- renamed to telit-evk-pro3
v2:
- init.c: remove 9260ek and g20ek references
- init.c: rename ek_ -> evk_
- init.c: cleanup headers
- init.c: use clock framework
- init.c: remove function ek_set_board_type
- init.c: remove bus_width_16 initialization
arch/arm/Makefile | 1 +
arch/arm/boards/telit-evk-pro3/Makefile | 1 +
arch/arm/boards/telit-evk-pro3/config.h | 6 +
arch/arm/boards/telit-evk-pro3/env/boot/nand-ubi | 10 ++
.../boards/telit-evk-pro3/env/init/config-board | 8 +
.../boards/telit-evk-pro3/env/init/mtdparts-nand | 11 ++
arch/arm/boards/telit-evk-pro3/env/init/usb | 26 +++
arch/arm/boards/telit-evk-pro3/init.c | 178 +++++++++++++++++++++
arch/arm/configs/telit_evk_pro3_defconfig | 73 +++++++++
arch/arm/mach-at91/Kconfig | 9 ++
10 files changed, 323 insertions(+)
create mode 100644 arch/arm/boards/telit-evk-pro3/Makefile
create mode 100644 arch/arm/boards/telit-evk-pro3/config.h
create mode 100644 arch/arm/boards/telit-evk-pro3/env/boot/nand-ubi
create mode 100644 arch/arm/boards/telit-evk-pro3/env/init/config-board
create mode 100644 arch/arm/boards/telit-evk-pro3/env/init/mtdparts-nand
create mode 100644 arch/arm/boards/telit-evk-pro3/env/init/usb
create mode 100644 arch/arm/boards/telit-evk-pro3/init.c
create mode 100644 arch/arm/configs/telit_evk_pro3_defconfig
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index a36adfb..60661eb 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -94,6 +94,7 @@ board-$(CONFIG_MACH_EUKREA_CPUIMX35) := eukrea_cpuimx35
board-$(CONFIG_MACH_EUKREA_CPUIMX51SD) := eukrea_cpuimx51
board-$(CONFIG_MACH_FREESCALE_MX25_3STACK) := freescale-mx25-3-stack
board-$(CONFIG_MACH_FREESCALE_MX35_3STACK) := freescale-mx35-3-stack
+board-$(CONFIG_MACH_GE863) := telit-evk-pro3
board-$(CONFIG_MACH_IMX21ADS) := imx21ads
board-$(CONFIG_MACH_IMX27ADS) := imx27ads
board-$(CONFIG_MACH_IMX233_OLINUXINO) := imx233-olinuxino
diff --git a/arch/arm/boards/telit-evk-pro3/Makefile b/arch/arm/boards/telit-evk-pro3/Makefile
new file mode 100644
index 0000000..eb072c0
--- /dev/null
+++ b/arch/arm/boards/telit-evk-pro3/Makefile
@@ -0,0 +1 @@
+obj-y += init.o
diff --git a/arch/arm/boards/telit-evk-pro3/config.h b/arch/arm/boards/telit-evk-pro3/config.h
new file mode 100644
index 0000000..7aeff30
--- /dev/null
+++ b/arch/arm/boards/telit-evk-pro3/config.h
@@ -0,0 +1,6 @@
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define AT91_MAIN_CLOCK 6000000 /* 6.000 MHz crystal */
+
+#endif /* __CONFIG_H */
diff --git a/arch/arm/boards/telit-evk-pro3/env/boot/nand-ubi b/arch/arm/boards/telit-evk-pro3/env/boot/nand-ubi
new file mode 100644
index 0000000..1987492
--- /dev/null
+++ b/arch/arm/boards/telit-evk-pro3/env/boot/nand-ubi
@@ -0,0 +1,10 @@
+#!/bin/sh
+
+if [ "$1" = menu ]; then
+ boot-menu-add-entry "$0" "nand (UBI)"
+ exit
+fi
+
+global.bootm.image="/dev/nand0.kernel.bb"
+#global.bootm.oftree="/env/oftree"
+global.linux.bootargs.dyn.root="root=ubi0:rootfs ubi.mtd=nand0.rootfs rootfstype=ubifs"
diff --git a/arch/arm/boards/telit-evk-pro3/env/init/config-board b/arch/arm/boards/telit-evk-pro3/env/init/config-board
new file mode 100644
index 0000000..741b902
--- /dev/null
+++ b/arch/arm/boards/telit-evk-pro3/env/init/config-board
@@ -0,0 +1,8 @@
+#!/bin/sh
+
+# board defaults, do not change in running system. Change /env/config
+# instead
+
+global.hostname=evk-pro3
+global.linux.bootargs.base="console=ttyS0,115200"
+global.boot.default=nand-ubi
diff --git a/arch/arm/boards/telit-evk-pro3/env/init/mtdparts-nand b/arch/arm/boards/telit-evk-pro3/env/init/mtdparts-nand
new file mode 100644
index 0000000..58e859b
--- /dev/null
+++ b/arch/arm/boards/telit-evk-pro3/env/init/mtdparts-nand
@@ -0,0 +1,11 @@
+#!/bin/sh
+
+if [ "$1" = menu ]; then
+ init-menu-add-entry "$0" "NAND partitions"
+ exit
+fi
+
+mtdparts="0xC0000(nand0.bootstrap),256k(nand0.barebox)ro,128k(nand0.bareboxenv),3M(nand0.kernel),-(nand0.rootfs)"
+kernelname="atmel_nand"
+
+mtdparts-add -b -d nand0 -k ${kernelname} -p ${mtdparts}
diff --git a/arch/arm/boards/telit-evk-pro3/env/init/usb b/arch/arm/boards/telit-evk-pro3/env/init/usb
new file mode 100644
index 0000000..afa0416
--- /dev/null
+++ b/arch/arm/boards/telit-evk-pro3/env/init/usb
@@ -0,0 +1,26 @@
+#!/bin/sh
+
+# Uncomment the following line to enalbe dfu instead of usbserial
+#dfu_enabled="y"
+
+product_id=0x1234
+vendor_id=0x4321
+
+dfu_config="/dev/nand0.bootstrap.bb(bootstrap)sr,/dev/nand0.barebox.bb(barebox)sr,/dev/nand0.kernel.bb(kernel)r,/dev/nand0.rootfs.bb(rootfs)r"
+
+if [ $at91_udc0.vbus != 1 ]; then
+ echo
+ echo "No USB Device cable plugged, normal boot"
+ exit
+fi
+
+if [ -n $dfu_enabled ]; then
+ echo
+ echo "Start DFU Mode"
+ dfu ${dfu_config} -P ${product_id} -V ${vendor_id}
+fi
+
+global.autoboot_timeout=16
+echo
+echo "enable tty over USB Device, increase the boot delay to ${global.autoboot_timeout}s"
+usbserial
diff --git a/arch/arm/boards/telit-evk-pro3/init.c b/arch/arm/boards/telit-evk-pro3/init.c
new file mode 100644
index 0000000..06e6508
--- /dev/null
+++ b/arch/arm/boards/telit-evk-pro3/init.c
@@ -0,0 +1,178 @@
+/*
+ * Copyright (C) 2007 Sascha Hauer, Pengutronix
+ * Copyright (C) 2013 Fabio Porcedda <fabio.porcedda at gmail.com>, Telit
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <asm/armlinux.h>
+#include <common.h>
+#include <gpio.h>
+#include <init.h>
+#include <linux/clk.h>
+#include <mach/at91_rstc.h>
+#include <mach/at91sam9_smc.h>
+#include <mach/board.h>
+#include <mach/io.h>
+#include <nand.h>
+
+#define BOOTSTRAP_SIZE 0xC0000
+
+static struct atmel_nand_data nand_pdata = {
+ .ale = 21,
+ .cle = 22,
+ .det_pin = -EINVAL,
+ .rdy_pin = AT91_PIN_PC13,
+ .enable_pin = AT91_PIN_PC14,
+ .on_flash_bbt = 1,
+};
+
+static struct sam9_smc_config evk_nand_smc_config = {
+ .ncs_read_setup = 0,
+ .nrd_setup = 1,
+ .ncs_write_setup = 0,
+ .nwe_setup = 1,
+
+ .ncs_read_pulse = 3,
+ .nrd_pulse = 3,
+ .ncs_write_pulse = 3,
+ .nwe_pulse = 3,
+
+ .read_cycle = 5,
+ .write_cycle = 5,
+
+ .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
+ AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
+ .tdf_cycles = 2,
+};
+
+static void evk_add_device_nand(void)
+{
+ /* configure chip-select 3 (NAND) */
+ sam9_smc_configure(0, 3, &evk_nand_smc_config);
+
+ at91_add_device_nand(&nand_pdata);
+}
+
+static struct at91_ether_platform_data macb_pdata = {
+ .is_rmii = 1,
+ .phy_addr = 0,
+};
+
+static void evk_phy_reset(void)
+{
+ unsigned long rstc;
+ struct clk *clk = clk_get(NULL, "macb_clk");
+
+ clk_enable(clk);
+
+ at91_set_gpio_input(AT91_PIN_PA14, 0);
+ at91_set_gpio_input(AT91_PIN_PA15, 0);
+ at91_set_gpio_input(AT91_PIN_PA17, 0);
+ at91_set_gpio_input(AT91_PIN_PA25, 0);
+ at91_set_gpio_input(AT91_PIN_PA26, 0);
+ at91_set_gpio_input(AT91_PIN_PA28, 0);
+
+ rstc = at91_sys_read(AT91_RSTC_MR) & AT91_RSTC_ERSTL;
+
+ /* Need to reset PHY -> 500ms reset */
+ at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
+ (AT91_RSTC_ERSTL & (0x0d << 8)) |
+ AT91_RSTC_URSTEN);
+
+ at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_EXTRST);
+
+ /* Wait for end hardware reset */
+ while (!(at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_NRSTL))
+ ;
+
+ /* Restore NRST value */
+ at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
+ (rstc) |
+ AT91_RSTC_URSTEN);
+}
+
+/*
+ * MCI (SD/MMC)
+ */
+#if defined(CONFIG_MCI_ATMEL)
+static struct atmel_mci_platform_data __initdata evk_mci_data = {
+ .bus_width = 4,
+ .slot_b = 1,
+};
+
+static void evk_usb_add_device_mci(void)
+{
+ at91_add_device_mci(0, &evk_mci_data);
+}
+#else
+static void evk_usb_add_device_mci(void) {}
+#endif
+
+/*
+ * USB Host port
+ */
+static struct at91_usbh_data __initdata evk_usbh_data = {
+ .ports = 2,
+ .vbus_pin = { -EINVAL, -EINVAL },
+};
+
+/*
+ * USB Device port
+ */
+static struct at91_udc_data __initdata evk_udc_data = {
+ .vbus_pin = AT91_PIN_PC4,
+ .pullup_pin = -EINVAL, /* pull-up driven by UDC */
+};
+
+static int evk_mem_init(void)
+{
+ at91_add_device_sdram(0);
+
+ return 0;
+}
+mem_initcall(evk_mem_init);
+
+static int evk_devices_init(void)
+{
+ evk_add_device_nand();
+ evk_phy_reset();
+ at91_add_device_eth(0, &macb_pdata);
+ at91_add_device_usbh_ohci(&evk_usbh_data);
+ at91_add_device_udc(&evk_udc_data);
+ evk_usb_add_device_mci();
+
+ armlinux_set_bootparams((void *)(AT91_CHIPSELECT_1 + 0x100));
+
+ devfs_add_partition("nand0", 0x00000, BOOTSTRAP_SIZE,
+ DEVFS_PARTITION_FIXED, "bootstrap_raw");
+ dev_add_bb_dev("bootstrap_raw", "bootstrap");
+ devfs_add_partition("nand0", BOOTSTRAP_SIZE, SZ_256K,
+ DEVFS_PARTITION_FIXED, "self_raw");
+ dev_add_bb_dev("self_raw", "self0");
+ devfs_add_partition("nand0", BOOTSTRAP_SIZE + SZ_256K, SZ_128K,
+ DEVFS_PARTITION_FIXED, "env_raw");
+ dev_add_bb_dev("env_raw", "env0");
+ devfs_add_partition("nand0", BOOTSTRAP_SIZE + SZ_256K + SZ_128K,
+ SZ_128K, DEVFS_PARTITION_FIXED, "env_raw1");
+ dev_add_bb_dev("env_raw1", "env1");
+
+ return 0;
+}
+
+device_initcall(evk_devices_init);
+
+static int evk_console_init(void)
+{
+ at91_register_uart(0, 0);
+ return 0;
+}
+console_initcall(evk_console_init);
diff --git a/arch/arm/configs/telit_evk_pro3_defconfig b/arch/arm/configs/telit_evk_pro3_defconfig
new file mode 100644
index 0000000..050d176
--- /dev/null
+++ b/arch/arm/configs/telit_evk_pro3_defconfig
@@ -0,0 +1,73 @@
+CONFIG_ARCH_AT91SAM9260=y
+CONFIG_MACH_GE863=y
+CONFIG_BAREBOX_MAX_IMAGE_SIZE=0x40000
+CONFIG_AEABI=y
+# CONFIG_CMD_ARM_CPUINFO is not set
+CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
+CONFIG_PBL_IMAGE=y
+CONFIG_MMU=y
+CONFIG_EXPERIMENTAL=y
+CONFIG_PROMPT="EVK-PRO3:"
+CONFIG_LONGHELP=y
+CONFIG_PROMPT_HUSH_PS2="y"
+CONFIG_HUSH_FANCY_PROMPT=y
+CONFIG_CMDLINE_EDITING=y
+CONFIG_AUTO_COMPLETE=y
+CONFIG_CONSOLE_ACTIVATE_ALL=y
+CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y
+CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/telit-evk-pro3/env"
+CONFIG_CMD_EDIT=y
+CONFIG_CMD_SLEEP=y
+CONFIG_CMD_SAVEENV=y
+CONFIG_CMD_EXPORT=y
+CONFIG_CMD_PRINTENV=y
+CONFIG_CMD_READLINE=y
+CONFIG_CMD_TFTP=y
+CONFIG_CMD_ECHO_E=y
+CONFIG_CMD_LOADB=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_FLASH=y
+CONFIG_CMD_UBIFORMAT=y
+CONFIG_CMD_BOOTM_SHOW_TYPE=y
+CONFIG_CMD_BOOTM_INITRD=y
+CONFIG_CMD_BOOTM_OFTREE=y
+CONFIG_CMD_BOOTM_OFTREE_UIMAGE=y
+CONFIG_CMD_UIMAGE=y
+# CONFIG_CMD_BOOTU is not set
+CONFIG_CMD_RESET=y
+CONFIG_CMD_GO=y
+CONFIG_CMD_OFTREE=y
+CONFIG_CMD_MTEST=y
+CONFIG_CMD_MTEST_ALTERNATIVE=y
+CONFIG_CMD_TIMEOUT=y
+CONFIG_CMD_PARTITION=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_LED=y
+CONFIG_CMD_LED_TRIGGER=y
+CONFIG_NET=y
+CONFIG_NET_DHCP=y
+CONFIG_NET_NFS=y
+CONFIG_NET_PING=y
+CONFIG_NET_NETCONSOLE=y
+CONFIG_DRIVER_NET_MACB=y
+# CONFIG_SPI is not set
+CONFIG_MTD=y
+# CONFIG_MTD_OOB_DEVICE is not set
+CONFIG_NAND=y
+# CONFIG_NAND_ECC_HW is not set
+# CONFIG_NAND_ECC_HW_SYNDROME is not set
+# CONFIG_NAND_ECC_HW_NONE is not set
+CONFIG_NAND_ATMEL=y
+CONFIG_UBI=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_DFU=y
+CONFIG_USB_GADGET_SERIAL=y
+CONFIG_MCI=y
+CONFIG_MCI_STARTUP=y
+CONFIG_MCI_ATMEL=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_LED_TRIGGERS=y
+CONFIG_FS_TFTP=y
+CONFIG_FS_FAT=y
+CONFIG_FS_FAT_LFN=y
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index fcba7fb..a319bd3 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -46,6 +46,7 @@ config BOARDINFO
default "Calao TNY-A9263" if MACH_TNY_A9263
default "Calao TNY-A9G20" if MACH_TNY_A9G20
default "Calao QIL-A9260" if MACH_QIL_A9260
+ default "Telit EVK-PRO3" if MACH_GE863
config HAVE_NAND_ATMEL_BUSWIDTH_16
bool
@@ -235,6 +236,14 @@ config MACH_USB_A9260
Select this if you are using a Calao Systems USB-A9260.
<http://www.calao-systems.com>
+config MACH_GE863
+ bool "Telit EVK-PRO3"
+ select HAVE_NAND_ATMEL_BUSWIDTH_16
+ select HAVE_DEFAULT_ENVIRONMENT_NEW
+ help
+ Say y here if you are using Telit EVK-PRO3 with GE863-PRO3
+ <http://www.telit.com>
+
endchoice
endif
--
1.8.0.3
More information about the barebox
mailing list