[PATCH 1/1 v3] input: add qt1070 touch keyboard support
Jean-Christophe PLAGNIOL-VILLARD
plagnioj at jcrosoft.com
Sat Nov 3 07:26:19 EDT 2012
use irq pin as the pin is asserted untill we clear it
This will allow to do not poll on i2c which slow down barebox
If no irq_pin is provided fall back on i2c polling
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
---
v3:
add irq_pin support
use different poll function to wait for calibration and reset
so we do not endup with a delay of nearly 500ms at boot time
Best Regards,
J.
drivers/input/Kconfig | 8 ++
drivers/input/Makefile | 1 +
drivers/input/qt1070.c | 296 ++++++++++++++++++++++++++++++++++++++++++++++++
include/input/qt1070.h | 18 +++
4 files changed, 323 insertions(+)
create mode 100644 drivers/input/qt1070.c
create mode 100644 include/input/qt1070.h
diff --git a/drivers/input/Kconfig b/drivers/input/Kconfig
index 15979a2..846483c 100644
--- a/drivers/input/Kconfig
+++ b/drivers/input/Kconfig
@@ -30,4 +30,12 @@ config KEYBOARD_IMX_KEYPAD
setup logic must also provide a 'matrix_keymap_data' structure,
defining the used keys.
+config KEYBOARD_QT1070
+ tristate "Atmel AT42QT1070 Touch Sensor Chip"
+ depends on I2C
+ select POLLER
+ help
+ Say Y here if you want to use Atmel AT42QT1070 QTouch
+ Sensor chip as input device.
+
endmenu
diff --git a/drivers/input/Makefile b/drivers/input/Makefile
index 3d105cc..d042980 100644
--- a/drivers/input/Makefile
+++ b/drivers/input/Makefile
@@ -1,2 +1,3 @@
obj-$(CONFIG_KEYBOARD_GPIO) += gpio_keys.o
obj-$(CONFIG_KEYBOARD_IMX_KEYPAD) += imx_keypad.o
+obj-$(CONFIG_KEYBOARD_QT1070) += qt1070.o
diff --git a/drivers/input/qt1070.c b/drivers/input/qt1070.c
new file mode 100644
index 0000000..c66189e
--- /dev/null
+++ b/drivers/input/qt1070.c
@@ -0,0 +1,296 @@
+/*
+ * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
+ *
+ * Under GPLv2
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <init.h>
+#include <clock.h>
+#include <poller.h>
+#include <kfifo.h>
+#include <i2c/i2c.h>
+#include <malloc.h>
+#include <readkey.h>
+#include <input/qt1070.h>
+#include <gpio.h>
+
+#define QT1070_CHIP_ID 0x2e
+
+#define QT1070_READ_CHIP_ID 0x00
+#define QT1070_FW_VERSION 0x01
+#define QT1070_DET_STATUS 0x02
+#define QT1070_KEY_STATUS 0x03
+
+/* Calibrate */
+#define QT1070_CALIBRATE_CMD 0x38
+#define QT1070_CAL_TIME 200
+
+/* Reset */
+#define QT1070_RESET 0x39
+#define QT1070_RESET_TIME 255
+
+static int default_code[QT1070_NB_BUTTONS] = {
+ KEY_ENTER, KEY_HOME, KEY_UP, KEY_DOWN,
+ KEY_RIGHT, KEY_LEFT, KEY_CLEAR_SCREEN };
+
+struct qt1070_data {
+ int code[QT1070_NB_BUTTONS];
+
+ int irq_pin;
+
+ u64 start;
+
+ /* optional */
+ int fifo_size;
+
+ struct i2c_client *client;
+ u8 button_state[QT1070_NB_BUTTONS];
+ u8 previous_state;
+
+ struct kfifo *recv_fifo;
+ struct poller_struct poller;
+ struct console_device cdev;
+};
+
+static inline struct qt1070_data *
+poller_to_qt_data(struct poller_struct *poller)
+{
+ return container_of(poller, struct qt1070_data, poller);
+}
+
+static inline struct qt1070_data *
+cdev_to_qt_data(struct console_device *cdev)
+{
+ return container_of(cdev, struct qt1070_data, cdev);
+}
+
+static bool qt1070_read(struct qt1070_data *data, u8 reg, u8 *val)
+{
+ int ret;
+
+ ret = i2c_read_reg(data->client, reg, val, 1);
+
+ if (ret < 0)
+ return ret;
+ if (ret != 1)
+ return -EIO;
+ return 0;
+}
+
+static bool qt1070_write(struct qt1070_data *data, u8 reg, const u8 val)
+{
+ int ret;
+
+ ret = i2c_write_reg(data->client, reg, &val, 1);
+ if (ret < 0)
+ return ret;
+ if (ret != 1)
+ return -EIO;
+ return 0;
+}
+
+static void qt1070_poller(struct poller_struct *poller)
+{
+ struct qt1070_data *data = poller_to_qt_data(poller);
+ int i;
+ u8 buf, bt;
+ u8 mask = 0x1;
+
+ if (gpio_is_valid(data->irq_pin)) {
+ /* active low */
+ if (gpio_get_value(data->irq_pin))
+ return;
+ }
+
+ qt1070_read(data, QT1070_DET_STATUS, &buf);
+
+ if (qt1070_read(data, QT1070_KEY_STATUS, &buf))
+ return;
+
+ if (!buf & !data->previous_state)
+ return;
+
+ for (i = 0; i < QT1070_NB_BUTTONS; i++) {
+ bt = buf & mask;
+
+ if (!bt && data->button_state[i]) {
+ dev_dbg(data->cdev.dev, "release key(%d) as %d\n", i, data->code[i]);
+ kfifo_put(data->recv_fifo, (u_char*)&data->code[i], sizeof(int));
+ } else if (bt) {
+ dev_dbg(data->cdev.dev, "pressed key(%d) as %d\n", i, data->code[i]);
+ }
+
+ data->button_state[i] = bt;
+ mask <<= 1;
+ }
+
+ data->previous_state = buf;
+}
+
+static void qt1070_reset_poller(struct poller_struct *poller)
+{
+ struct qt1070_data *data = poller_to_qt_data(poller);
+ u8 buf;
+
+ if (!is_timeout_non_interruptible(data->start, QT1070_RESET_TIME * MSECOND))
+ return;
+
+ /* clear the status */
+ qt1070_read(data, QT1070_DET_STATUS, &buf);
+
+ poller->func = qt1070_poller;
+}
+
+static void qt1070_calibrate_poller(struct poller_struct *poller)
+{
+ struct qt1070_data *data = poller_to_qt_data(poller);
+ int ret;
+
+ if (!is_timeout_non_interruptible(data->start, QT1070_CAL_TIME * MSECOND))
+ return;
+
+ /* Soft reset */
+ ret = qt1070_write(data, QT1070_RESET, 1);
+ if (ret) {
+ dev_err(data->cdev.dev, "can not reset the chip (%d)\n", ret);
+ poller_unregister(poller);
+ return;
+ }
+ data->start = get_time_ns();
+
+ poller->func = qt1070_reset_poller;
+}
+
+static int qt1070_tstc(struct console_device *cdev)
+{
+ struct qt1070_data *data = cdev_to_qt_data(cdev);
+
+ return (kfifo_len(data->recv_fifo) == 0) ? 0 : 1;
+}
+
+static int qt1070_getc(struct console_device *cdev)
+{
+ int code = 0;
+ struct qt1070_data *data = cdev_to_qt_data(cdev);
+
+ kfifo_get(data->recv_fifo, (u_char*)&code, sizeof(int));
+ return code;
+}
+
+static int qt1070_pdata_init(struct device_d *dev, struct qt1070_data *data)
+{
+ struct qt1070_platform_data *pdata = dev->platform_data;
+ int ret;
+
+ if (!pdata)
+ return 0;
+
+ if (pdata->nb_code)
+ memcpy(data->code, pdata->code, sizeof(int) * pdata->nb_code);
+
+ if (!gpio_is_valid(pdata->irq_pin))
+ return 0;
+
+ ret = gpio_request(pdata->irq_pin, "qt1070");
+ if (ret)
+ return ret;
+
+ ret = gpio_direction_input(pdata->irq_pin);
+ if (ret)
+ goto err;
+
+ data->irq_pin = pdata->irq_pin;
+
+ return 0;
+err:
+ gpio_free(pdata->irq_pin);
+ return ret;
+}
+
+static int qt1070_probe(struct device_d *dev)
+{
+ struct console_device *cdev;
+ struct qt1070_data *data;
+ u8 fw_version, chip_id;
+ int ret;
+ char buf[6];
+
+ data = xzalloc(sizeof(*data));
+ data->client = to_i2c_client(dev);
+ data->irq_pin = -EINVAL;
+
+ ret = qt1070_read(data, QT1070_READ_CHIP_ID, &chip_id);
+ if (ret) {
+ dev_err(dev, "can not read chip id (%d)\n", ret);
+ goto err;
+ }
+
+ if (chip_id != QT1070_CHIP_ID) {
+ dev_err(dev, "unsupported id 0x%x\n", chip_id);
+ ret = -ENXIO;
+ goto err;
+ }
+
+ ret = qt1070_read(data, QT1070_FW_VERSION, &fw_version);
+ if (ret) {
+ dev_err(dev, "can not read firmware version (%d)\n", ret);
+ goto err;
+ }
+
+ sprintf(buf, "0x%x", fw_version);
+ dev_add_param_fixed(dev, "fw_version", buf);
+ sprintf(buf, "0x%x", chip_id);
+ dev_add_param_fixed(dev, "chip_ip", buf);
+
+ ret = qt1070_pdata_init(dev, data);
+ if (ret) {
+ dev_err(dev, "can not get pdata (%d)\n", ret);
+ goto err;
+ }
+
+ /* Calibrate device */
+ ret = qt1070_write(data, QT1070_CALIBRATE_CMD, 1);
+ if (ret) {
+ dev_err(dev, "can not calibrate the chip (%d)\n", ret);
+ goto err;
+ }
+ data->start = get_time_ns();
+
+ memcpy(data->code, default_code, sizeof(int) * ARRAY_SIZE(default_code));
+
+ data->fifo_size = 50;
+ data->recv_fifo = kfifo_alloc(data->fifo_size);
+
+ data->poller.func = qt1070_calibrate_poller;
+
+ cdev = &data->cdev;
+ cdev->dev = dev;
+ cdev->f_caps = CONSOLE_STDIN;
+ cdev->tstc = qt1070_tstc;
+ cdev->getc = qt1070_getc;
+
+ console_register(&data->cdev);
+
+ ret = poller_register(&data->poller);
+ if (ret)
+ goto err;
+
+ return 0;
+err:
+ free(data);
+ return ret;
+}
+
+static struct driver_d qt1070_driver = {
+ .name = "qt1070",
+ .probe = qt1070_probe,
+};
+
+static int qt1070_init(void)
+{
+ i2c_register_driver(&qt1070_driver);
+ return 0;
+}
+device_initcall(qt1070_init);
diff --git a/include/input/qt1070.h b/include/input/qt1070.h
new file mode 100644
index 0000000..014f67b
--- /dev/null
+++ b/include/input/qt1070.h
@@ -0,0 +1,18 @@
+/*
+ * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
+ *
+ * Under GPLv2
+ */
+
+#ifndef __QT1070_H__
+#define __QT1070_H__
+
+#define QT1070_NB_BUTTONS 7
+
+struct qt1070_platform_data {
+ int code[QT1070_NB_BUTTONS];
+ int nb_code;
+ int irq_pin;
+};
+
+#endif /* __QT1070_H__ */
--
1.7.10.4
More information about the barebox
mailing list