[PATCH 1/9] Support most Samsung SoCs in S3C serial driver

[Alexey Galakhov]

Signed-off-by: Alexey Galakhov <agalakhov at gmail.com>
---
 arch/arm/mach-samsung/include/mach/s3c-generic.h |    4 ++
 arch/arm/mach-samsung/s3c24xx-clocks.c           |   17 +++++++
 drivers/serial/serial_s3c.c                      |   55 +++++++++++++++-------
 3 files changed, 59 insertions(+), 17 deletions(-)

diff --git a/arch/arm/mach-samsung/include/mach/s3c-generic.h b/arch/arm/mach-samsung/include/mach/s3c-generic.h
index 4ea3dd7..5d3808e 100644
--- a/arch/arm/mach-samsung/include/mach/s3c-generic.h
+++ b/arch/arm/mach-samsung/include/mach/s3c-generic.h
@@ -30,5 +30,9 @@ uint32_t s3c_get_fclk(void);
 uint32_t s3c_get_hclk(void);
 uint32_t s3c_get_pclk(void);
 uint32_t s3c_get_uclk(void);
+
+unsigned s3c_get_uart_clk(unsigned src);
+
 uint32_t s3c24xx_get_memory_size(void);
+
 void s3c24xx_disable_second_sdram_bank(void);
diff --git a/arch/arm/mach-samsung/s3c24xx-clocks.c b/arch/arm/mach-samsung/s3c24xx-clocks.c
index a99d1b9..38d8b75 100644
--- a/arch/arm/mach-samsung/s3c24xx-clocks.c
+++ b/arch/arm/mach-samsung/s3c24xx-clocks.c
@@ -117,6 +117,23 @@ uint32_t s3c24_get_uclk(void)
 	return s3c_get_upllclk();
 }
 
+/** 
+ * Return correct UART frequency based on the UCON register
+ */
+unsigned s3c_get_uart_clk(unsigned src)
+{
+	switch (src & 3) {
+	case 0:
+	case 2:
+		return s3c_get_pclk();
+	case 1:
+		return 0; /* TODO UEXTCLK */
+	case 3:
+		return 0; /* TODO FCLK/n */
+	}
+	return 0; /* not reached, to make compiler happy */
+}
+
 /**
  * Show the user the current clock settings
  */
diff --git a/drivers/serial/serial_s3c.c b/drivers/serial/serial_s3c.c
index 2bdc1df..7a9b355 100644
--- a/drivers/serial/serial_s3c.c
+++ b/drivers/serial/serial_s3c.c
@@ -40,6 +40,17 @@
 #define UTXH 0x20		/* transmitt */
 #define URXH 0x24		/* receive */
 #define UBRDIV 0x28		/* baudrate generator */
+#ifdef S3C_UART_HAS_UBRDIVSLOT
+# define UBRDIVSLOT 0x2c	/* baudrate slot generator */
+#endif
+#ifdef S3C_UART_HAS_UINTM
+# define UINTM 0x38		/* interrupt mask register */
+#endif
+
+#ifndef S3C_UART_CLKSEL
+/* Use pclk */
+# define S3C_UART_CLKSEL 0
+#endif
 
 struct s3c_uart {
 	void __iomem *regs;
@@ -51,26 +62,32 @@ struct s3c_uart {
 static unsigned s3c_get_arch_uart_input_clock(void __iomem *base)
 {
 	unsigned reg = readw(base + UCON);
-
-	switch (reg & 0xc00) {
-		case 0x000:
-		case 0x800:
-			return s3c_get_pclk();
-		case 0x400:
-			break;	/* TODO UEXTCLK */
-		case 0xc00:
-			break;	/* TODO FCLK/n */
-	}
-
-	return 0;	/* not nice, but we can't emit an error message! */
+	reg = (reg >> 10) & 0x3;
+	return s3c_get_uart_clk(reg);
 }
 
+#ifdef S3C_UART_HAS_UBRDIVSLOT
+/*
+ * This table takes the fractional value of the baud divisor and gives
+ * the recommended setting for the UDIVSLOT register. Refer the datasheet
+ * for further details
+ */
+static const uint16_t udivslot_table[] __maybe_unused = {
+	0x0000, 0x0080, 0x0808, 0x0888, 0x2222, 0x4924, 0x4A52, 0x54AA,
+	0x5555, 0xD555, 0xD5D5, 0xDDD5, 0xDDDD, 0xDFDD, 0xDFDF, 0xFFDF,
+};
+#endif
+
 static int s3c_serial_setbaudrate(struct console_device *cdev, int baudrate)
 {
 	struct s3c_uart *priv = to_s3c_uart(cdev);
 	void __iomem *base = priv->regs;
 	unsigned val;
 
+#ifdef S3C_UART_HAS_UBRDIVSLOT
+	val = s3c_get_arch_uart_input_clock(base) / baudrate;
+	writew(udivslot_table[val & 15], base + UBRDIVSLOT);
+#endif
 	val = s3c_get_arch_uart_input_clock(base) / (16 * baudrate) - 1;
 	writew(val, base + UBRDIV);
 
@@ -88,11 +105,15 @@ static int s3c_serial_init_port(struct console_device *cdev)
 
 	/* Normal,No parity,1 stop,8 bit */
 	writeb(0x03, base + ULCON);
-	/*
-	 * tx=level,rx=edge,disable timeout int.,enable rx error int.,
-	 * normal,interrupt or polling
-	 */
-	writew(0x0245, base + UCON);
+
+	/* tx=level,rx=edge,disable timeout int.,enable rx error int.,
+	 * normal, interrupt or polling, no pre-divider */
+	writew(0x0245 | ((S3C_UART_CLKSEL) << 10), base + UCON);
+
+#ifdef S3C_UART_HAS_UINTM
+	/* 'interrupt or polling mode' for both directions */
+	writeb(0xf, base + UINTM);
+#endif
 
 #ifdef CONFIG_DRIVER_SERIAL_S3C_AUTOSYNC
 	writeb(0x10, base + UMCON); /* enable auto flow control */
-- 
1.7.10