[PATCH v3 3/4] pm9g45: enable MCI0

[Sascha Hauer]

On Wed, Mar 21, 2012 at 06:27:25PM +0200, Asen Chavdarov Dimov wrote:
> FIXME: part of or no data is written. File copy ends
> with message: "atmel_mci at atmel_mci0: command/data timeout"

Should I apply these patches? These FIXMEs seem to say that they don't
work.

Sascha

> 
> Signed-off-by: Asen Chavdarov Dimov <dimov at ronetix.at>
> ---
> since v1:
> 	add_device_mci renamed to pm9g45_add_device_mci
> 
> since v2:
> 	- used savedefconfig to minimize the config file
> ---
>  arch/arm/boards/pm9g45/init.c     |   16 ++++++++++++++++
>  arch/arm/configs/pm9g45_defconfig |    7 +++++--
>  2 files changed, 21 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm/boards/pm9g45/init.c b/arch/arm/boards/pm9g45/init.c
> index 567bad4..174dd75 100644
> --- a/arch/arm/boards/pm9g45/init.c
> +++ b/arch/arm/boards/pm9g45/init.c
> @@ -77,6 +77,21 @@ static void pm_add_device_nand(void)
>  	at91_add_device_nand(&nand_pdata);
>  }
>  
> +#if defined(CONFIG_MCI_ATMEL)
> +static struct atmel_mci_platform_data __initdata mci_data = {
> +	.bus_width	= 4,
> +	.wp_pin		= 0,
> +	.detect_pin	= AT91_PIN_PD6,
> +};
> +
> +static void pm9g45_add_device_mci(void)
> +{
> +	at91_add_device_mci(0, &mci_data);
> +}
> +#else
> +static void pm9g45_add_device_mci(void) {}
> +#endif
> +
>  static struct at91_ether_platform_data macb_pdata = {
>  	.flags = AT91SAM_ETHER_RMII,
>  	.phy_addr = 0,
> @@ -104,6 +119,7 @@ mem_initcall(pm9g45_mem_init);
>  static int pm9g45_devices_init(void)
>  {
>  	pm_add_device_nand();
> +	pm9g45_add_device_mci();
>  	pm9g45_phy_init();
>  	at91_add_device_eth(&macb_pdata);
>  
> diff --git a/arch/arm/configs/pm9g45_defconfig b/arch/arm/configs/pm9g45_defconfig
> index d199abd..8106202 100644
> --- a/arch/arm/configs/pm9g45_defconfig
> +++ b/arch/arm/configs/pm9g45_defconfig
> @@ -4,8 +4,6 @@ CONFIG_AEABI=y
>  CONFIG_LONGHELP=y
>  CONFIG_CMDLINE_EDITING=y
>  CONFIG_AUTO_COMPLETE=y
> -CONFIG_PARTITION=y
> -CONFIG_PARTITION_DISK=y
>  CONFIG_DEFAULT_ENVIRONMENT_GENERIC=y
>  CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/pm9g45/env"
>  CONFIG_POLLER=y
> @@ -35,4 +33,9 @@ CONFIG_MTD=y
>  CONFIG_NAND=y
>  CONFIG_NAND_ATMEL=y
>  CONFIG_UBI=y
> +CONFIG_MCI=y
> +CONFIG_MCI_ATMEL=y
>  CONFIG_EEPROM_AT25=y
> +CONFIG_FS_FAT=y
> +CONFIG_FS_FAT_WRITE=y
> +CONFIG_FS_FAT_LFN=y
> -- 
> 1.7.4.4
> 
> 
> _______________________________________________
> barebox mailing list
> barebox at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
> 

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |