Antwort: Re: Re: Re: Re: nor flash board init code
Sascha Hauer
s.hauer at pengutronix.de
Mon Jul 30 13:05:37 EDT 2012
Hi Christian,
Please stop top-posting on Mailing lists.
Sascha
On Mon, Jul 30, 2012 at 04:49:17PM +0200, christian.buettner at rafi.de wrote:
> ok tried it like this:
>
> #define ECUv6_ECSPI1_CS0 IMX_GPIO_NR(2, 30)
> #define ECUv6_ECSPI1_CS1 IMX_GPIO_NR(3, 19)
>
> //SPI + NOR FLASH
> const struct flash_platform_data tx53_flash = {
> .type = "mx25l8005",
> .name = "spi_flash",
> };
>
>
> //MX25L8005MC-15G
> static const struct spi_board_info mx53_spi_board_info[] = {
> {
> .name = "m25p",
> .max_speed_hz = 30000000,
> .bus_num = 0,
> .chip_select = 0,
> .bits_per_word = 8,
> .mode = SPI_MODE_0,
> .platform_data = &tx53_flash,
> },
> };
>
> static int ecspi_0_cs[] = { ECUv6_ECSPI1_CS0,ECUv6_ECSPI1_CS1 };
>
>
> static struct spi_imx_master tx53_spi = {
> .chipselect = ecspi_0_cs,
> .num_chipselect = ARRAY_SIZE(ecspi_0_cs),
> };
>
>
> answer from spi eeprom is unknown:
> m25p at m25p0: unrecognized JEDEC id ffffff
>
> Hasn't anyone used an SPI Flash with the imx53 yet?
>
> christian
>
>
>
> Von: Franck Jullien <franck.jullien at gmail.com>
> An: christian.buettner at rafi.de,
> Kopie: barebox at lists.infradead.org
> Datum: 30.07.2012 16:28
> Betreff: Re: Re: Re: Re: nor flash board init code
>
>
>
> 2012/7/30 <christian.buettner at rafi.de>:
> > i always get the response:
> >
> > m25p at m25p0: unrecognized JEDEC id ffffff
> >
> > SPI Flah:MX25L8005MC-15G
> > CPU: imx53
> >
> > Here is my board init code:
> >
> > //SPI + FLASH structs
> > const struct flash_platform_data tx53_flash = {
> > .type = "mx25l8005",
> > .name = "spi_flash",
> > };
> >
> >
> > //MX25L8005MC-15G
> > static const struct spi_board_info mx53_spi_board_info[] = {
> > {
> > .name = "m25p",
> > .max_speed_hz = 30000000,
> > .bus_num = 0,
> > .chip_select = 0,
> > .bits_per_word = 8,
> > .mode = SPI_MODE_0,
> > .platform_data = &tx53_flash,
> > },
> > };
> >
> > static struct spi_imx_master tx53_spi = {
> > .num_chipselect = 1,
> > };
> >
>
> I'm not familiar with the IMX spi but in the tx51 or ccxmx51 board
> file one can read:
>
> static struct spi_imx_master tx51_spi_0_data = {
> .chipselect = spi_0_cs,
> .num_chipselect = ARRAY_SIZE(spi_0_cs),
> };
>
> #define CCXMX51_ECSPI1_CS0 IMX_GPIO_NR(4, 24)
> #define CCXMX51_ECSPI1_CS1 IMX_GPIO_NR(4, 25)
>
> static int ecspi_0_cs[] = { CCXMX51_ECSPI1_CS0, CCXMX51_ECSPI1_CS1, };
>
> static struct spi_imx_master ecspi_0_data = {
> .chipselect = ecspi_0_cs,
> .num_chipselect = ARRAY_SIZE(ecspi_0_cs),
> };
>
> Don't you need to set .chipselect ?
>
>
> >
> >
> > //PIN MUX:
> > MX53_PAD_EIM_D17__ECSPI1_MISO, //SPI MISO - EEPROM SO
> > MX53_PAD_EIM_D18__ECSPI1_MOSI, //SPI MOSI - EEPROM SI
> > MX53_PAD_EIM_D16__ECSPI1_SCLK, //SPI SCLK - EEPROM SCK
> > MX53_PAD_EIM_EB2__ECSPI1_SS0, //SPI SS1 - EEPROM CS
> >
> >
> > //device init code:
> > spi_register_board_info(mx53_spi_board_info,
> > ARRAY_SIZE(mx53_spi_board_info));
> >
> > imx53_add_spi0(&tx53_spi);
> >
> >
> > Any ideas, whats wrong?
> >
> > christian
> >
> >
> > Von: Franck Jullien <franck.jullien at gmail.com>
> > An: christian.buettner at rafi.de,
> > Kopie: barebox at lists.infradead.org
> > Datum: 30.07.2012 10:33
> > Betreff: Re: Re: Re: nor flash board init code
> > ________________________________
> >
> >
> >
> > 2012/7/30 <christian.buettner at rafi.de>:
> >> Whooosch and it worked!
> >>
> >> devinfo
> >> devices:
> >> ...
> >> `---- mem1
> >> `---- 0x00000000-0xfffffffe: /dev/mem
> >> `---- i2c-imx2
> >> `---- imx_spi0
> >> `---- m25p0
> >> `---- fec_imx0
> >> `---- miidev0
> >> ...
> >>
> >> barebox:/ devinfo m25p0
> >> resources:
> >> driver: none
> >>
> >> no parameters available
> >> barebox:/
> >>
> >> But why is driver in devinfo = none?
> >>
> >
> > It used to work. You need to find why it doesn't work anymore ;)
> >
> >> christian
> >>
> >>
> >> Von: Franck Jullien <franck.jullien at gmail.com>
> >> An: christian.buettner at rafi.de,
> >> Kopie: barebox at lists.infradead.org
> >> Datum: 30.07.2012 10:07
> >> Betreff: Re: Re: nor flash board init code
> >> ________________________________
> >>
> >>
> >>
> >> Hi,
> >>
> >> 2012/7/30 <christian.buettner at rafi.de>
> >>>
> >>> Thanks for the code!
> >>>
> >>> Here is my approach:
> >>>
> >>> const struct flash_platform_data tx53_flash = {
> >>> .type = "mx25l8005",
> >>> .name = "spi_flash",
> >>> };
> >>>
> >>>
> >>> //MX25L8005MC-15G
> >>> static const struct spi_board_info mx53_spi_board_info[] = {
> >>> {
> >>> .name = "mx25l8005",
> >>
> >>
> >> Here sould be the driver name: .name = "m25p",
> >>
> >>>
> >>> .max_speed_hz = 70000000,
> >>> .bus_num = 0,
> >>> .chip_select = 0,
> >>> .bits_per_word = 8,
> >>> .mode = SPI_MODE_0,
> >>> .platform_data = &tx53_flash,
> >>> },
> >>> };
> >>>
> >>> static struct spi_imx_master tx53_spi = {
> >>> .num_chipselect = 1,
> >>> };
> >>>
> >>>
> >>> init_devices {
> >>>
> >>> ...
> >>> spi_register_board_info(mx53_spi_board_info,
> >>> ARRAY_SIZE(mx53_spi_board_info));
> >>>
> >>> add_generic_device("m25p",-1,"m25p",MX53_ECSPI1_BASE_ADDR,64 *
> >>> 1024,IORESOURCE_MEM,&mx53_spi_board_info);
> >>
> >> You have to add the SPI master device here. The m25p device will be
> >> probed automagically (AFAIR).
> >>
> >>
> >>>
> >>> ...
> >>> }
> >>>
> >>>
> >>> When the m25p80.c driver probes i get no spi instance:
> >>>
> >>> static int m25p_probe(struct device_d *dev) {
> >>> struct spi_device *spi = (struct spi_device *)dev->type_data;
> >>> const struct spi_device_id *id = NULL;
> >>> ...
> >>> }
> >>>
> >>> struct spi_device *spi is always null
> >>>
> >>> Whats wrong here?
> >>>
> >>> christian
> >>>
> >>>
> >>>
> >>> Von: Franck Jullien <franck.jullien at gmail.com>
> >>> An: christian.buettner at rafi.de,
> >>> Kopie: barebox at lists.infradead.org
> >>> Datum: 27.07.2012 13:33
> >>> Betreff: Re: nor flash board init code
> >>> ________________________________
> >>>
> >>>
> >>>
> >>> 2012/7/25 <christian.buettner at rafi.de>
> >>> >
> >>> > hi all,
> >>> > is there any example board init code to load the mx25l8005 spi
> >>> > nor-flash
> >>> > through the imx53 (TX53 from KARO)?
> >>> > I want to use the m25p80 driver to read and write.
> >>> >
> >>> > christian
> >>> > _______________________________________________
> >>> > barebox mailing list
> >>> > barebox at lists.infradead.org
> >>> > http://lists.infradead.org/mailman/listinfo/barebox
> >>> >
> >>>
> >>> Hi Christian,
> >>>
> >>> This is what I use with the Altera SPI controller + an SPI flash
> device:
> >>>
> >>>
> >>>
> >>>
> http://www.elec4fun.fr/index.php?option=com_content&view=article&id=10&Itemid=153
>
> >>>
> >>> static struct spi_altera_master altera_spi_0_data = {
> >>> .num_chipselect = 1,
> >>> .spi_mode = 0, /* SPI mode of the EPCS flash controller */
> >>> .databits = 8, /* Data length of the EPCS flash controller
> */
> >>> .speed = 20000000, /* EPCS flash controller speed */
> >>> };
> >>>
> >>>
> >>> static struct flash_platform_data epcs_flash = {
> >>> .name = "epcs", /* Cdev name, optional */
> >>> .type = "m25p40", /* Device type, required for non JEDEC chips
> */
> >>> };
> >>>
> >>> static struct spi_board_info generic_spi_board_info[] = {
> >>> {
> >>> .name = "m25p",
> >>> .max_speed_hz = 20000000,
> >>> .bus_num = 0,
> >>> .chip_select = 0,
> >>> .bits_per_word = 8,
> >>> .mode = SPI_MODE_0,
> >>> .platform_data = &epcs_flash,
> >>> }
> >>> };
> >>>
> >>> static int myboard_devices_init(void) {
> >>>
> >>> ...
> >>>
> >>> spi_register_board_info(myboard_spi_board_info,
> >>> ARRAY_SIZE(myboard_spi_board_info));
> >>>
> >>> add_generic_device("altera_spi", -1, NULL, NIOS_SOPC_EPCS_BASE, 0x18,
> >>> IORESOURCE_MEM, &altera_spi_0_data);
> >>>
> >>> ...
> >>>
> >>> Franck.
> >>>
> >>
> >> Franck.
> >>
> >
>
> Do you have a scope ? This is the easiest way to debug SPI ;)
>
> _______________________________________________
> barebox mailing list
> barebox at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
More information about the barebox
mailing list