i.MX35 3-stack use only 128MB RAM
Boaz Ben-David
boaz.bd at wellsense-tech.com
Wed Apr 20 08:10:50 EDT 2011
Hi,
I'm glad it's helpful to you.
I don't want to take the credit here, I forgot to write this is
the procedure we got from Freescale's support when we contacted them.
Sorry for not mentioning this at first, I thought I did... (:
Boaz Ben-David
R&D Engineer
Tel: +972.2.6470.700Mob: +972.54.678.1511Email: boaz.bd at wellsense-tech.com
www.themapsystem.com
Please consider the impact on the environment before printing this e-mail and/or the attachment(s).
________________________________________
From: barebox-bounces at lists.infradead.org [barebox-bounces at lists.infradead.org] On Behalf Of Thomas Mayer [tm.telemotive at gmx.de]
Sent: Wednesday, April 20, 2011 3:06 PM
To: barebox at lists.infradead.org
Subject: Re: i.MX35 3-stack use only 128MB RAM
Hi,
wow this was a really quick and good answer, thanks a lot!
I will test it and try to adapt it to barebox too.
Regards,
Thomas
Am 20.04.2011 13:20, schrieb Boaz Ben-David:
> Hi,
>
> This is the procedure for modifying Redboot to support 256MB of RAM in Redboot, you can adapt it to barebox:
>
> How to extend RAM for Linux on MX35PDK
> =======================================
>
> Tested on: redboot_200910, MX35PDK green board, MX35 TO2, DDR2, SDK1.5
>
> The current redboot images enable just half of the physically available DDR2 memory (128MB on MX35PDK).
> This is due to the fact that redboot is only enabling SDCS0 (BANK0) and not SDCS1.
> It seems that there was a little bug in redboot which has prevented the enablement of SDCS1 and so
> nobody has tried this again. Physically the bank1 is working properly on MX35PDK CPU module.
>
> Step0
> =====
>
> Check memory size of existing redboot on your MX35PDK
>
> under redboot check memory on SDCS1 which is mapped physically to 0x90000000.
> You may also use 0x08000000 which is the first virtual address on SDCS1.
> Note in redboot, the virtual address 0x80000000 is mapped to physical address 0x80000000 non cashable.
> Virtual Address 0x0 is mapped to physical address 0x80000000 cashable.
> The virtual address 0x90000000 is not in the MMU table. That is why we receive a "illegal memory address" error message.
> This is not a memory exception because no memory transaction has taken place.
> See also below...
>
>
> RedBoot> dump -b 0x90000000
> 90000000: ** command abort - illegal memory access?
> RedBoot> dump -b 0x08000000
> 08000000: ** command abort - illegal memory access?
> RedBoot> dump -b 0x07ffff00
> 07FFFF00: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF |................|
> 07FFFF10: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF |................|
>
> After booting linux use command "free":
>
> root at freescale ~$ free
> total used free shared buffers
> Mem: 126140 9920 116220 0 0
> Swap: 0 0 0
> Total: 126140 9920 116220
>
> You have about 128MB free memory. But not 256MB.
>
>
> Step 1
> ======
>
> We will edit and recompile redboot. For this you may untar the redboot_200910.tgz archive in the linux BSP source
> on your linux host.
> Unpack redboot and configure the build process as described in
> redboot_200910/doc/redboot_mx35.pdf Chapter 6
>
> You should be able to run successfully:
>
> ecosconfig new mx35_3stack redboot
> ecosconfig import $ECOS_REPOSITORY/hal/arm/mx35/3stack/current/misc/redboot_ROMRAM.ecm
> ecosconfig tree
> make
>
> Step 2
> ======
>
> We will know edit some redboot source files as discribed below. Look at the comment
> "// by michael for 256MB".
>
>
> ~/redboot_200910/src/ecos/packages/hal/arm/mx35/3stack/current/include/pkgconf/mlt_arm_board_romram.h
>
> #ifndef __ASSEMBLER__
> #include<cyg/infra/cyg_type.h>
> #include<stddef.h>
>
> #endif
> #define CYGMEM_REGION_ram (0x00000000)
> #define CYGMEM_REGION_ram_SIZE (0x0FF00000) // by michael for 256MB
> #define CYGMEM_REGION_ram_ATTR (CYGMEM_REGION_ATTR_R | CYGMEM_REGION_ATTR_W)
> #define CYGMEM_REGION_rom (0x87F00000)
> #define CYGMEM_REGION_rom_SIZE (0x100000)
> #define CYGMEM_REGION_rom_ATTR (CYGMEM_REGION_ATTR_R)
> #ifndef __ASSEMBLER__
> extern char CYG_LABEL_NAME (__heap1) [];
> #endif
> #define CYGMEM_SECTION_heap1 (CYG_LABEL_NAME (__heap1))
> #define CYGMEM_SECTION_heap1_SIZE (CYGMEM_REGION_ram_SIZE - (size_t) CYG_LABEL_NAME (__heap1))
>
>
> ~/redboot_200910/src/ecos/packages/hal/arm/mx35/3stack/current/include/hal_plaform_setup.h line 712:
>
> ldr r0, ESDCTL_BASE_W
> /* deleted by michael
> mov r3, #0x2000
> str r3, [r0, #0x0]
> ldr r2, ROM_VER_ADDR_W
> ldr r4, [r2]
> cmp r4, #0x1
> streq r3, [r0, #0x8]
> */
> mov r12, #0x00
> mov r2, #0x0 // DDR2
> mov r1, #RAM_BANK0_BASE
> bl setup_sdram_bank
> cmp r3, #0x0
> 3: bne 3b // loop forever if bank0 is not OK
>
> /* do not repeat with mDDR settings. We know we have DDR2 (r2=0)
> cmp r3, #0x0
> orreq r12, r12, #1
> eorne r2, r2, #0x1
> blne setup_sdram_bank
> */
> #if 1 // do the same for bank1
> /* CSD1 */
> mov r12, #0x00
> mov r2, #0x0 // DDR2
> mov r1, #RAM_BANK1_BASE
> bl setup_sdram_bank
> cmp r3, #0x0
> 4: bne 4b //loop forever if bank1 is not OK
>
>
> /* do not try with mDDR again for bank1. we know we have DDR2
> beq 1b
> eorne r2, r2, #0x1
> blne setup_sdram_bank
> orr r12, r12, #1
> 1:
> */
> #endif
>
> ~/redboot_200910/src/ecos/packages/hal/arm/mx35/3stack/current/include/fsl_board.h
>
> /* MX35 3-Stack SDRAM is from 0x90000000, 64M */
> #define SDRAM_BASE_ADDR CSD0_BASE_ADDR
> //#define SDRAM_SIZE 0x08000000
> #define SDRAM_SIZE 0x10000000 // by michael for 256MB
> #define RAM_BANK0_BASE CSD0_BASE_ADDR
> #define RAM_BANK1_BASE CSD1_BASE_ADDR
>
>
> ~/redboot_200910/src/ecos/packages/hal/arm/mx35/3stack/current/src/board_misc.c
>
> /* Actual Virtual Size Attributes Function */
> /* Base Base MB cached? buffered? access permissions */
> /* xxx00000 xxx00000 */
> X_ARM_MMU_SECTION(0x000, 0xF00, 0x1, ARM_UNCACHEABLE, ARM_UNBUFFERABLE, ARM_ACCESS_PERM_RW_RW); /* ROM */
> X_ARM_MMU_SECTION(0x100, 0x100, 0x1, ARM_UNCACHEABLE, ARM_UNBUFFERABLE, ARM_ACCESS_PERM_RW_RW); /* iRAM */
> X_ARM_MMU_SECTION(0x300, 0x300, 0x1, ARM_UNCACHEABLE, ARM_UNBUFFERABLE, ARM_ACCESS_PERM_RW_RW); /* L2CC */
> X_ARM_MMU_SECTION(0x400, 0x400, 0x400, ARM_UNCACHEABLE, ARM_UNBUFFERABLE, ARM_ACCESS_PERM_RW_RW); /* Internal Regsisters upto SDRAM*/
> X_ARM_MMU_SECTION(0x800, 0x000, 0x80, ARM_CACHEABLE, ARM_BUFFERABLE, ARM_ACCESS_PERM_RW_RW); /* SDRAM 0:128M*/
> X_ARM_MMU_SECTION(0x800, 0x800, 0x80, ARM_CACHEABLE, ARM_BUFFERABLE, ARM_ACCESS_PERM_RW_RW); /* SDRAM 0:128M*/
> X_ARM_MMU_SECTION(0x800, 0x880, 0x80, ARM_UNCACHEABLE, ARM_UNBUFFERABLE, ARM_ACCESS_PERM_RW_RW); /* SDRAM 0:128M*/
> // start by michael for 256MB. Enter new MMU entries for SDCS1
> X_ARM_MMU_SECTION(0x900, 0x080, 0x80, ARM_CACHEABLE, ARM_BUFFERABLE, ARM_ACCESS_PERM_RW_RW); /* SDRAM 1:128M*/
> X_ARM_MMU_SECTION(0x900, 0x900, 0x80, ARM_CACHEABLE, ARM_BUFFERABLE, ARM_ACCESS_PERM_RW_RW); /* SDRAM 1:128M*/
> X_ARM_MMU_SECTION(0x900, 0x980, 0x80, ARM_CACHEABLE, ARM_BUFFERABLE, ARM_ACCESS_PERM_RW_RW); /* SDRAM 1:128M*/
> // end by michael for 256MB
> X_ARM_MMU_SECTION(0xA00, 0xA00, 0x40, ARM_CACHEABLE, ARM_BUFFERABLE, ARM_ACCESS_PERM_RW_RW); /* Flash */
> X_ARM_MMU_SECTION(0xB00, 0xB00, 0x20, ARM_CACHEABLE, ARM_BUFFERABLE, ARM_ACCESS_PERM_RW_RW); /* PSRAM */
> X_ARM_MMU_SECTION(0xB20, 0xB20, 0x1E0, ARM_UNCACHEABLE, ARM_UNBUFFERABLE,ARM_ACCESS_PERM_RW_RW); /* ESDCTL, WEIM, M3IF, EMI, NFC, External I/O */
>
>
> Step 4
> ======
>
> rebuild redboot. Now it comes:
>
> The make scripte does not recognize any changes in hal_platform_setup.h file because this file is been used to build
> the lib "vectors". This is not in the dependencies of the make script. It is either not removed by "make clean".
> You have to remove the vectors.o by hand.
>
> So to properly rebuild redboot you need to:
>
> cd ~/redboot_200910/src/ecos
> rm install/lib/vectors.*
> make
> cp install/bin/redboot.bin ~/shared_folder/redboot_mx35_TO2_256MB.bin # if you have a VMWare and use a shared_folder in ~/shared_folder
>
>
> Step 5
> ======
>
> Flash new redboot to MX35PDK using ATK1.6. You do not need to erase the NAND flash. So, you keep the
> same fconfig settings. Do not forget the BBT tick!
>
>
> Step 6
> ======
>
> Check the new memories:
>
> RedBoot> dump -b 0x90000000
> 90000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
> 90000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
>
>
> root at freescale ~$ free
> total used free shared buffers
> Mem: 256088 10040 246048 0 0
> Swap: 0 0 0
> Total: 256088 10040 246048
>
>
>
>
> Boaz Ben-David
> R&D Engineer
>
> Tel: +972.2.6470.700Mob: +972.54.678.1511Email: boaz.bd at wellsense-tech.com
> www.themapsystem.com
>
>
> Please consider the impact on the environment before printing this e-mail and/or the attachment(s).
> ________________________________________
> From: barebox-bounces at lists.infradead.org [barebox-bounces at lists.infradead.org] On Behalf Of Thomas Mayer [thomas.mayer at telemotive.de]
> Sent: Wednesday, April 20, 2011 1:56 PM
> To: barebox at lists.infradead.org
> Subject: i.MX35 3-stack use only 128MB RAM
>
> Hi,
>
> I read in the freescale documentation "U-Boot for i.MX35 based Designs"
> that the i.MX35 3-stack board has 256MB SDRAM, but we can use only 128MB
> because the second chip select isn't configured. Depending on the
> circuit diagrams I think "CSD1" isn't configured.
> I looked already in the datasheet of the cpu, but I couldn't found a
> solution for this problem.
>
> Have anybody ever tried to enable this second chip select?
>
>
> Regards,
> Thomas
>
> _______________________________________________
> barebox mailing list
> barebox at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
>
> _______________________________________________
> barebox mailing list
> barebox at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
>
_______________________________________________
barebox mailing list
barebox at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
More information about the barebox
mailing list