[PATCH ath-next] wifi: ath11k: don't create a duplicate peer on the same pdev
Fernando Tapia
fernan.tapia at fernandotapia.eu
Fri Nov 13 04:03:25 PST 2026
ath11k_peer_create() accepts an address that is already a peer on
another vdev, assuming the station is moving to another band. That holds
when the old vdev is on another pdev. When both vdevs are on the same
pdev, for example two AP interfaces on one 2.4 GHz radio, a station that
moves between the two BSSes is authenticated on the new one while hostapd
still has it on the old one. The WMI_PEER_CREATE for the second vdev then
makes the IPQ8074 firmware (WLAN.HK.2.9.0.1-02146) assert:
wal_peer_control.c:2904 Assertion is_graceful_to_handle failed
followed by "failed to find peer ... after creation" on the host, and on
AHB the whole SoC reboots. Tuya devices in pairing mode, which try both
BSSes of a radio within a second, cause a reboot loop.
Refuse the peer with -EBUSY while the address is still a peer on another
vdev of the same pdev, without sending the command to the firmware. The
station add fails as it already does after the assert, hostapd rejects
that authentication, and the client succeeds on a retry once its old
station is removed.
Tested on a Xiaomi AX3600 (OpenWrt 25.12.5, kernel 6.12.94 with ath11k
backported from 6.18.26) for 8 days. A smart plug moved between the two
SSIDs of the 2.4 GHz radio in both directions, the sequence that had
rebooted the router 8 times before: the new warning appears, the client
connects on the retry about 4 s later, no firmware assert, no reboot.
Link: https://github.com/openwrt/openwrt/issues/24864
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.9.0.1-02146-QCAHKSWPL_SILICONZ-1
Assisted-by: Claude:claude-sonnet-5-5
Signed-off-by: Fernando Tapia <fernan.tapia at fernandotapia.eu>
---
drivers/net/wireless/ath/ath11k/peer.c | 31 ++++++++++++++++++++++++++
1 file changed, 31 insertions(+)
diff --git a/drivers/net/wireless/ath/ath11k/peer.c b/drivers/net/wireless/ath/ath11k/peer.c
index b30a90698..95379930d 100644
--- a/drivers/net/wireless/ath/ath11k/peer.c
+++ b/drivers/net/wireless/ath/ath11k/peer.c
@@ -367,11 +367,25 @@ static int ath11k_wait_for_peer_created(struct ath11k *ar, int vdev_id, const u8
return ath11k_wait_for_peer_common(ar->ab, vdev_id, addr, true);
}
+static bool ath11k_peer_vdev_on_pdev(struct ath11k *ar, u32 vdev_id)
+{
+ struct ath11k_vif *arvif;
+
+ lockdep_assert_held(&ar->conf_mutex);
+
+ list_for_each_entry(arvif, &ar->arvifs, list)
+ if (arvif->vdev_id == vdev_id)
+ return true;
+
+ return false;
+}
+
int ath11k_peer_create(struct ath11k *ar, struct ath11k_vif *arvif,
struct ieee80211_sta *sta, struct peer_create_params *param)
{
struct ath11k_peer *peer;
struct ath11k_sta *arsta;
+ int old_vdev_id;
int ret, fbret;
lockdep_assert_held(&ar->conf_mutex);
@@ -392,6 +406,23 @@ int ath11k_peer_create(struct ath11k *ar, struct ath11k_vif *arvif,
return -EINVAL;
}
+ /* The firmware asserts (wal_peer_control.c
+ * "is_graceful_to_handle") when a peer is created for an
+ * address that is still a peer on another vdev of the same
+ * pdev. This happens when a station moves between two BSSes
+ * of one radio before its old station is removed. Refuse the
+ * new peer until the old one is gone.
+ */
+ if (ath11k_peer_vdev_on_pdev(ar, peer->vdev_id)) {
+ old_vdev_id = peer->vdev_id;
+ spin_unlock_bh(&ar->ab->base_lock);
+ mutex_unlock(&ar->ab->tbl_mtx_lock);
+ ath11k_warn(ar->ab,
+ "peer %pM still exists on vdev %d, not creating it on vdev %u\n",
+ param->peer_addr, old_vdev_id, param->vdev_id);
+ return -EBUSY;
+ }
+
/* Assume sta is transitioning to another band.
* Remove here the peer from rhash.
*/
--
2.43.0
More information about the ath11k
mailing list