[PATCH v4 02/12] ath11k: Add HW params for WCN6750

[Manikanta Pubbisetty]

On 4/27/2022 10:51 AM, Kalle Valo wrote:
> Manikanta Pubbisetty <quic_mpubbise at quicinc.com> writes:
> 
>> Add HW params for WCN6750. It is similar to the HW params
>> of QCA6390 with few differences wrt DP APIs and register
>> offsets.
>>
>> Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
>> Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
>> Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
>> Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
>>
>> Signed-off-by: Manikanta Pubbisetty <quic_mpubbise at quicinc.com>
>> ---
>>   drivers/net/wireless/ath/ath11k/core.c | 61 ++++++++++++++++++++++++++
>>   drivers/net/wireless/ath/ath11k/core.h |  1 +
>>   drivers/net/wireless/ath/ath11k/qmi.h  |  2 +
>>   3 files changed, 64 insertions(+)
>>
>> diff --git a/drivers/net/wireless/ath/ath11k/core.c b/drivers/net/wireless/ath/ath11k/core.c
>> index cbac1919867f..8695f999acb2 100644
>> --- a/drivers/net/wireless/ath/ath11k/core.c
>> +++ b/drivers/net/wireless/ath/ath11k/core.c
>> @@ -427,6 +427,67 @@ static const struct ath11k_hw_params ath11k_hw_params[] = {
>>   		.dbr_debug_support = false,
>>   		.global_reset = true,
>>   	},
>> +	{
>> +		.name = "wcn6750 hw1.0",
>> +		.hw_rev = ATH11K_HW_WCN6750_HW10,
>> +		.fw = {
>> +			.dir = "WCN6750/hw1.0",
>> +			.board_size = 256 * 1024,
>> +			.cal_offset = 128 * 1024,
>> +		},
>> +		.max_radios = 1,
>> +		.bdf_addr = 0x4B0C0000,
>> +		.ring_mask = &ath11k_hw_ring_mask_qca6390,
>> +		.internal_sleep_clock = false,
>> +		.qmi_service_ins_id = ATH11K_QMI_WLFW_SERVICE_INS_ID_V01_WCN6750,
>> +		.host_ce_config = ath11k_host_ce_config_qca6390,
>> +		.ce_count = 9,
>> +		.target_ce_config = ath11k_target_ce_config_wlan_qca6390,
>> +		.target_ce_count = 9,
>> +		.svc_to_ce_map = ath11k_target_service_to_ce_map_wlan_qca6390,
>> +		.svc_to_ce_map_len = 14,
>> +		.rfkill_pin = 0,
>> +		.rfkill_cfg = 0,
>> +		.rfkill_on_level = 0,
>> +		.single_pdev_only = true,
>> +		.rxdma1_enable = false,
>> +		.num_rxmda_per_pdev = 1,
>> +		.rx_mac_buf_ring = true,
>> +		.vdev_start_delay = true,
>> +		.htt_peer_map_v2 = false,
>> +
>> +		.spectral = {
>> +			.fft_sz = 0,
>> +			.fft_pad_sz = 0,
>> +			.summary_pad_sz = 0,
>> +			.fft_hdr_len = 0,
>> +			.max_fft_bins = 0,
>> +		},
>> +
>> +		.interface_modes = BIT(NL80211_IFTYPE_STATION) |
>> +					BIT(NL80211_IFTYPE_AP),
>> +		.supports_monitor = false,
>> +		.supports_shadow_regs = true,
>> +		.idle_ps = true,
>> +		.supports_sta_ps = true,
>> +		.cold_boot_calib = false,
>> +		.fw_mem_mode = 0,
>> +		.num_vdevs = 16 + 1,
>> +		.num_peers = 512,
>> +		.supports_suspend = false,
>> +		.supports_regdb = true,
>> +		.fix_l1ss = false,
>> +		.credit_flow = true,
>> +		.max_tx_ring = DP_TCL_NUM_RING_MAX_QCA6390,
>> +		.hal_params = &ath11k_hw_hal_params_qca6390,
>> +		.supports_dynamic_smps_6ghz = false,
>> +		.alloc_cacheable_memory = false,
>> +		.supports_rssi_stats = true,
>> +		.fw_wmi_diag_event = false,
>> +		.current_cc_support = true,
>> +		.dbr_debug_support = false,
>> +		.global_reset = false,
>> +	},
> 
> In the pending branch I added:
> 
> +               .bios_sar_capa = NULL,
> 

This is the only other change I had in V5, thanks for adding this.

Manikanta