[PATCH] ath11k: add hw_param for wakeup_mhi

[Kalle Valo]

Seevalamuthu Mariappan <quic_seevalam at quicinc.com> wrote:

> Wakeup mhi is needed before pci_read/write only for QCA6390 and WCN6855. Since
> wakeup & release mhi is enabled for all hardwares, below mhi assert is seen in
> QCN9074 when doing 'rmmod ath11k_pci':
> 
>         Kernel panic - not syncing: dev_wake != 0
>         CPU: 2 PID: 13535 Comm: procd Not tainted 4.4.60 #1
>         Hardware name: Generic DT based system
>         [<80316dac>] (unwind_backtrace) from [<80313700>] (show_stack+0x10/0x14)
>         [<80313700>] (show_stack) from [<805135dc>] (dump_stack+0x7c/0x9c)
>         [<805135dc>] (dump_stack) from [<8032136c>] (panic+0x84/0x1f8)
>         [<8032136c>] (panic) from [<80549b24>] (mhi_pm_disable_transition+0x3b8/0x5b8)
>         [<80549b24>] (mhi_pm_disable_transition) from [<80549ddc>] (mhi_power_down+0xb8/0x100)
>         [<80549ddc>] (mhi_power_down) from [<7f5242b0>] (ath11k_mhi_op_status_cb+0x284/0x3ac [ath11k_pci])
>         [E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
>         [E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
>         [E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
>         [<7f5242b0>] (ath11k_mhi_op_status_cb [ath11k_pci]) from [<7f524878>] (ath11k_mhi_stop+0x10/0x20 [ath11k_pci])
>         [<7f524878>] (ath11k_mhi_stop [ath11k_pci]) from [<7f525b94>] (ath11k_pci_power_down+0x54/0x90 [ath11k_pci])
>         [<7f525b94>] (ath11k_pci_power_down [ath11k_pci]) from [<8056b2a8>] (pci_device_shutdown+0x30/0x44)
>         [<8056b2a8>] (pci_device_shutdown) from [<805cfa0c>] (device_shutdown+0x124/0x174)
>         [<805cfa0c>] (device_shutdown) from [<8033aaa4>] (kernel_restart+0xc/0x50)
>         [<8033aaa4>] (kernel_restart) from [<8033ada8>] (SyS_reboot+0x178/0x1ec)
>         [<8033ada8>] (SyS_reboot) from [<80301b80>] (ret_fast_syscall+0x0/0x34)
> 
> Hence, disable wakeup/release mhi using hw_param for other hardwares.
> 
> Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01060-QCAHKSWPL_SILICONZ-1
> 
> Fixes: a05bd8513335 ("ath11k: read and write registers below unwindowed address")
> Signed-off-by: Seevalamuthu Mariappan <quic_seevalam at quicinc.com>
> Signed-off-by: Kalle Valo <kvalo at codeaurora.org>

Patch applied to ath-next branch of ath.git, thanks.

081e2d6476e3 ath11k: add hw_param for wakeup_mhi

-- 
https://patchwork.kernel.org/project/linux-wireless/patch/1636702019-26142-1-git-send-email-quic_seevalam@quicinc.com/

https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches