failed to run otp: -22

Adrian Chadd adrian at freebsd.org
Mon Apr 23 12:07:40 PDT 2018


Hi,

That's designed for debugging. It means you'll have an invalid MAC
address and no calibration information so your NIC won't work very
well.

The reason why needs to be figured out!



-adrian


On 23 April 2018 at 09:56, Arvid Picciani <aep at exys.org> wrote:
> Hi,
>
> Is it ok to run a QCA9880 with skip_otp=1?
> It's working fine with skip_ota, but just want to confirm this is safe.
>
> without skip_otp, mine isn't coming up because of "failed to run otp: -22"
>
> [    9.287905] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
> [    9.293912] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1
> irq_mode 0 reset_mode 0
> [    9.568820] ath10k_pci 0000:00:00.0: Direct firmware load for
> ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2
> [    9.579896] ath10k_pci 0000:00:00.0: Falling back to user helper
> [    9.737064] firmware ath10k!pre-cal-pci-0000:00:00.0.bin:
> firmware_loading_store: map pages failed
> [    9.746618] ath10k_pci 0000:00:00.0: Direct firmware load for
> ath10k/cal-pci-0000:00:00.0.bin failed with error -2
> [    9.757342] ath10k_pci 0000:00:00.0: Falling back to user helper
> [    9.909261] firmware ath10k!cal-pci-0000:00:00.0.bin:
> firmware_loading_store: map pages failed
> [    9.918500] ath10k_pci 0000:00:00.0: Direct firmware load for
> ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
> [    9.929582] ath10k_pci 0000:00:00.0: Falling back to user helper
> [   10.059370] firmware ath10k!QCA988X!hw2.0!firmware-6.bin:
> firmware_loading_store: map pages failed
> [   10.073667] ath10k_pci 0000:00:00.0: qca988x hw2.0 target
> 0x4100016c chip_id 0x043202ff sub 0000:0000
> [   10.083242] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1
> tracing 0 dfs 1 testmode 1
> [   10.096229] ath10k_pci 0000:00:00.0: firmware ver 10.2.4-1.0-00033
> api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 c41417d0
> [   10.189809] ath10k_pci 0000:00:00.0: Direct firmware load for
> ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
> [   10.200640] ath10k_pci 0000:00:00.0: Falling back to user helper
> [   10.271745] firmware ath10k!QCA988X!hw2.0!board-2.bin:
> firmware_loading_store: map pages failed
> [   10.299633] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A
> crc32 bebc7c08
> [   10.437761] ath10k_pci 0000:00:00.0: otp calibration failed: 2
> [   10.443792] ath10k_pci 0000:00:00.0: failed to run otp: -22
> [   10.449551] ath10k_pci 0000:00:00.0: could not init core (-22)
> [   10.455680] ath10k_pci 0000:00:00.0: could not probe fw (-22)
>
> _______________________________________________
> ath10k mailing list
> ath10k at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/ath10k



More information about the ath10k mailing list