WLE600VX from PCEngines
Janusz Dziedzic
janusz.dziedzic at tieto.com
Tue Sep 8 22:50:44 PDT 2015
On 8 September 2015 at 23:31, Marcel H. <maco at blava.net> wrote:
> Hi everyone,
> I have an interesting issue - I'm trying to run the QCA9882 based card
> in IBSS mode (to be used for BATMAN), however all I can do is to run
> in in 40Mhz channel width in 5GHz spectrum. Any attempt to run it in
> 80MHz width resolves in the following:
>
You should run IBSS using fresh wpa_supplicant (best latest code). By
default should run in 80MHz.
Other case is your regulatory - are you allow to use 80MHz on channel
157? First try 5180.
eg. of wpa_supplicant config:
network = {
ssid="test_ibss"
key_mgmt=NONE
mode=1
frequency=5180
}
BR
Janusz
> Interface wlan0
> ifindex 5
> wdev 0x1
> addr 04:f0:21:1b:5f:3b
> ssid my-mesh-network
> type IBSS
> wiphy 0
> channel 157 (5785 MHz), width: 40 MHz, center1: 5795 MHz
> root at voyage2:/opt/ca_node/bin# iw dev wlan0 set freq 5745 80
> command failed: Invalid argument (-22)
> root at voyage2:/opt/ca_node/bin# ip link set wlan0 down
> root at voyage2:/opt/ca_node/bin# iw dev wlan0 set freq 5745 80
> command failed: Invalid argument (-22)
>
>
> More info:
> =====================================================
> 06:00.0 Network controller: Qualcomm Atheros QCA988x 802.11ac Wireless
> Network Adapter
> Flags: bus master, fast devsel, latency 0, IRQ 27
> Memory at f7400000 (64-bit, non-prefetchable) [size=2M]
> Expansion ROM at f7600000 [disabled] [size=64K]
> Capabilities: [40] Power Management version 2
> Capabilities: [50] MSI: Enable+ Count=1/8 Maskable+ 64bit-
> Capabilities: [70] Express Endpoint, MSI 00
> Capabilities: [100] Advanced Error Reporting
> Capabilities: [140] Virtual Channel
> Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00
> Kernel driver in use: ath10k_pci
>
> root at voyage2:/opt/ca_node/bin# iw reg get
> country US: DFS-FCC
> (2402 - 2472 @ 40), (N/A, 30), (N/A)
> (5170 - 5250 @ 80), (N/A, 17), (N/A)
> (5250 - 5330 @ 80), (N/A, 23), (0 ms), DFS
> (5735 - 5835 @ 80), (N/A, 30), (N/A)
> (57240 - 63720 @ 2160), (N/A, 40), (N/A)
>
>
> root at voyage2:/opt/ca_node/bin# uname -a
> Linux voyage2 4.2.0-wl-ath-261216-gd89281c #1 SMP Tue Sep 8 14:03:33
> GMT 2015 i686 GNU/Linux
> (todays checkout from https://github.com/kvalo/ath + Voyage Linux 0.10 .config)
>
> root at voyage2:/lib/firmware/ath10k/QCA988X/hw2.0# md5sum ./firmware-2.bin
> e2db04b651c2b5ced4732f3f009a1cce ./firmware-2.bin
> (this is from the 'main' directory in the
> https://github.com/kvalo/ath10k-firmware)
>
>
> Wiphy phy0
> max # scan SSIDs: 16
> max scan IEs length: 195 bytes
> Retry short limit: 7
> Retry long limit: 4
> Coverage class: 0 (up to 0m)
> Device supports RSN-IBSS.
> Device supports AP-side u-APSD.
> Supported Ciphers:
> * WEP40 (00-0f-ac:1)
> * WEP104 (00-0f-ac:5)
> * TKIP (00-0f-ac:2)
> * CCMP (00-0f-ac:4)
> * CMAC (00-0f-ac:6)
> Available Antennas: TX 0x3 RX 0x3
> Configured Antennas: TX 0x3 RX 0x3
> Supported interface modes:
> * IBSS
> * managed
> * AP
> * AP/VLAN
> * monitor
> * P2P-client
> * P2P-GO
> * P2P-device
> Band 1:
> Capabilities: 0x19e3
> RX LDPC
> HT20/HT40
> Static SM Power Save
> RX HT20 SGI
> RX HT40 SGI
> TX STBC
> RX STBC 1-stream
> Max AMSDU length: 7935 bytes
> DSSS/CCK HT40
> Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
> Minimum RX AMPDU time spacing: 8 usec (0x06)
> HT TX/RX MCS rate indexes supported: 0-15
> VHT Capabilities (0x338001b2):
> Max MPDU length: 11454
> Supported Channel Width: neither 160 nor 80+80
> RX LDPC
> short GI (80 MHz)
> TX STBC
> RX antenna pattern consistency
> TX antenna pattern consistency
> VHT RX MCS set:
> 1 streams: MCS 0-9
> 2 streams: MCS 0-9
> 3 streams: not supported
> 4 streams: not supported
> 5 streams: not supported
> 6 streams: not supported
> 7 streams: not supported
> 8 streams: not supported
> VHT RX highest supported: 0 Mbps
> VHT TX MCS set:
> 1 streams: MCS 0-9
> 2 streams: MCS 0-9
> 3 streams: not supported
> 4 streams: not supported
> 5 streams: not supported
> 6 streams: not supported
> 7 streams: not supported
> 8 streams: not supported
> VHT TX highest supported: 0 Mbps
> Bitrates (non-HT):
> * 1.0 Mbps
> * 2.0 Mbps (short preamble supported)
> * 5.5 Mbps (short preamble supported)
> * 11.0 Mbps (short preamble supported)
> * 6.0 Mbps
> * 9.0 Mbps
> * 12.0 Mbps
> * 18.0 Mbps
> * 24.0 Mbps
> * 36.0 Mbps
> * 48.0 Mbps
> * 54.0 Mbps
> Frequencies:
> * 2412 MHz [1] (30.0 dBm)
> * 2417 MHz [2] (30.0 dBm)
> * 2422 MHz [3] (30.0 dBm)
> * 2427 MHz [4] (30.0 dBm)
> * 2432 MHz [5] (30.0 dBm)
> * 2437 MHz [6] (30.0 dBm)
> * 2442 MHz [7] (30.0 dBm)
> * 2447 MHz [8] (30.0 dBm)
> * 2452 MHz [9] (30.0 dBm)
> * 2457 MHz [10] (30.0 dBm)
> * 2462 MHz [11] (30.0 dBm)
> * 2467 MHz [12] (disabled)
> * 2472 MHz [13] (disabled)
> * 2484 MHz [14] (disabled)
> Band 2:
> Capabilities: 0x19e3
> RX LDPC
> HT20/HT40
> Static SM Power Save
> RX HT20 SGI
> RX HT40 SGI
> TX STBC
> RX STBC 1-stream
> Max AMSDU length: 7935 bytes
> DSSS/CCK HT40
> Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
> Minimum RX AMPDU time spacing: 8 usec (0x06)
> HT TX/RX MCS rate indexes supported: 0-15
> VHT Capabilities (0x338001b2):
> Max MPDU length: 11454
> Supported Channel Width: neither 160 nor 80+80
> RX LDPC
> short GI (80 MHz)
> TX STBC
> RX antenna pattern consistency
> TX antenna pattern consistency
> VHT RX MCS set:
> 1 streams: MCS 0-9
> 2 streams: MCS 0-9
> 3 streams: not supported
> 4 streams: not supported
> 5 streams: not supported
> 6 streams: not supported
> 7 streams: not supported
> 8 streams: not supported
> VHT RX highest supported: 0 Mbps
> VHT TX MCS set:
> 1 streams: MCS 0-9
> 2 streams: MCS 0-9
> 3 streams: not supported
> 4 streams: not supported
> 5 streams: not supported
> 6 streams: not supported
> 7 streams: not supported
> 8 streams: not supported
> VHT TX highest supported: 0 Mbps
> Bitrates (non-HT):
> * 6.0 Mbps
> * 9.0 Mbps
> * 12.0 Mbps
> * 18.0 Mbps
> * 24.0 Mbps
> * 36.0 Mbps
> * 48.0 Mbps
> * 54.0 Mbps
> Frequencies:
> * 5180 MHz [36] (17.0 dBm)
> * 5200 MHz [40] (17.0 dBm)
> * 5220 MHz [44] (17.0 dBm)
> * 5240 MHz [48] (17.0 dBm)
> * 5260 MHz [52] (23.0 dBm) (no IR, radar detection)
> DFS state: usable (for 1076 sec)
> DFS CAC time: 60000 ms
> * 5280 MHz [56] (23.0 dBm) (no IR, radar detection)
> DFS state: usable (for 1076 sec)
> DFS CAC time: 60000 ms
> * 5300 MHz [60] (23.0 dBm) (no IR, radar detection)
> DFS state: usable (for 1076 sec)
> DFS CAC time: 60000 ms
> * 5320 MHz [64] (23.0 dBm) (no IR, radar detection)
> DFS state: usable (for 1076 sec)
> DFS CAC time: 60000 ms
> * 5500 MHz [100] (disabled)
> * 5520 MHz [104] (disabled)
> * 5540 MHz [108] (disabled)
> * 5560 MHz [112] (disabled)
> * 5580 MHz [116] (disabled)
> * 5600 MHz [120] (disabled)
> * 5620 MHz [124] (disabled)
> * 5640 MHz [128] (disabled)
> * 5660 MHz [132] (disabled)
> * 5680 MHz [136] (disabled)
> * 5700 MHz [140] (disabled)
> * 5720 MHz [144] (disabled)
> * 5745 MHz [149] (30.0 dBm)
> * 5765 MHz [153] (30.0 dBm)
> * 5785 MHz [157] (30.0 dBm)
> * 5805 MHz [161] (30.0 dBm)
> * 5825 MHz [165] (30.0 dBm)
> Supported commands:
> * new_interface
> * set_interface
> * new_key
> * start_ap
> * new_station
> * set_bss
> * authenticate
> * associate
> * deauthenticate
> * disassociate
> * join_ibss
> * remain_on_channel
> * set_tx_bitrate_mask
> * frame
> * frame_wait_cancel
> * set_wiphy_netns
> * set_channel
> * set_wds_peer
> * probe_client
> * set_noack_map
> * register_beacons
> * start_p2p_device
> * set_mcast_rate
> * testmode
> * channel_switch
> * Unknown command (104)
> * connect
> * disconnect
> Supported TX frame types:
> * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90
> 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
> * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90
> 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
> * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0
> 0xb0 0xc0 0xd0 0xe0 0xf0
> * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90
> 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
> * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80
> 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
> * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80
> 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
> * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90
> 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
> * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80
> 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
> Supported RX frame types:
> * IBSS: 0x40 0xb0 0xc0 0xd0
> * managed: 0x40 0xd0
> * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
> * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
> * mesh point: 0xb0 0xc0 0xd0
> * P2P-client: 0x40 0xd0
> * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
> * P2P-device: 0x40 0xd0
> software interface modes (can always be added):
> * AP/VLAN
> * monitor
> valid interface combinations:
> * #{ managed, P2P-client } <= 8, #{ P2P-GO } <= 3, #{
> P2P-device } <= 1, #{ AP } <= 7,
> total <= 8, #channels <= 1, STA/AP BI must match
> HT Capability overrides:
> * MCS: ff ff ff ff ff ff ff ff ff ff
> * maximum A-MSDU length
> * supported channel width
> * short GI for 40 MHz
> * max A-MPDU length exponent
> * min MPDU start spacing
> Device supports TX status socket option.
> Device supports HT-IBSS.
> Device supports SAE with AUTHENTICATE command
> Device supports scan flush.
> Device supports per-vif TX power setting
> Driver supports a userspace MPM
> Driver/device bandwidth changes during BSS lifetime (AP/GO mode)
> Device supports static SMPS
> =====================================================
>
> I am grateful for any help here and do have some time to help
> debugging the issue.
>
> Marcel
>
> --
>
> ------------------------------------------------------
> This message is not intended to have
> contractual effect
> ------------------------------------------------------
>
> _______________________________________________
> ath10k mailing list
> ath10k at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/ath10k
More information about the ath10k
mailing list